connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='default', state=, avail=True, host='nuc-1', port=39083, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:39083 connected to 192.168.0.1 (port 39083) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.212 (8 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 3906641/tftp-deploy-kl0bua85/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906641/tftp-deploy-kl0bua85/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 2.9 MiB/s done Bytes transferred = 10789376 (a4a200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 3906641/tftp-deploy-kl0bua85/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906641/tftp-deploy-kl0bua85/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 3 MiB/s done Bytes transferred = 17520076 (10b55cc hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 3906641/tftp-deploy-kl0bua85/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906641/tftp-deploy-kl0bua85/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *###### 2.3 MiB/s done Bytes transferred = 73434 (11eda hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0xa4a200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17520012 Bytes = 16.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f94ed9 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc6 (KernelCI@build-j361444-arm-gcc-12-multi-v7-defconfig-config-thumb2-k6bx7) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Mon Nov 4 03:05:40 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: legacy bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 17 pages/cpu s40844 r8192 d20596 u69632 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524032 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.000000] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.000001] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.008577] Switching to timer-based delay loop, resolution 83ns <6>[ 0.015629] Console: colour dummy device 80x30 <6>[ 0.020560] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.031581] CPU: Testing write buffer coherency: ok <6>[ 0.036952] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.042566] CPU0: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.049421] pid_max: default: 32768 minimum: 301 <6>[ 0.054641] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.062496] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <3>[ 0.071623] /cpus/cpu@0 missing clock-frequency property <3>[ 0.077444] /cpus/cpu@1 missing clock-frequency property <3>[ 0.083287] /cpus/cpu@2 missing clock-frequency property <3>[ 0.089104] /cpus/cpu@3 missing clock-frequency property <6>[ 0.094908] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.102049] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.111323] rcu: Hierarchical SRCU implementation. <6>[ 0.116565] rcu: Max phase no-delay instances is 1000. <6>[ 0.122567] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.133525] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.142484] EFI services will not be available. <6>[ 0.147759] smp: Bringing up secondary CPUs ... <6>[ 0.153457] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.153476] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.170571] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.170590] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.187712] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.187732] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.204115] smp: Brought up 1 node, 4 CPUs <6>[ 0.208660] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.215342] CPU: All CPU(s) started in SVC mode. <6>[ 0.221059] Memory: 1967964K/2096128K available (11264K kernel code, 2543K rwdata, 6788K rodata, 2048K init, 430K bss, 59372K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.237931] devtmpfs: initialized <6>[ 0.258955] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.267405] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.277901] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.286764] pinctrl core: initialized pinctrl subsystem <6>[ 0.296225] DMI not present or invalid. <6>[ 0.301235] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.309906] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.321026] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.321086] cpuidle: using governor menu <6>[ 0.344753] platform 70000868.pinmux: Fixed dependency cycle(s) with /pinmux@70000868/pinmux <6>[ 0.379512] No ATAGs? <6>[ 0.382287] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.390883] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.413424] Serial: AMBA PL011 UART driver <3>[ 0.419303] tegra-mc 70019000.memory-controller: ppcsahbslvr: secure read @0x7fd41100: EMEM address decode error (EMEM decode error) <6>[ 0.450536] iommu: Default domain type: Translated <6>[ 0.455829] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.464477] SCSI subsystem initialized <6>[ 0.469143] usbcore: registered new interface driver usbfs <6>[ 0.475152] usbcore: registered new interface driver hub <6>[ 0.481002] usbcore: registered new device driver usb <6>[ 0.488188] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.493629] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.503407] PTP clock support registered <6>[ 0.507962] EDAC MC: Ver: 3.0.0 <6>[ 0.511875] scmi_core: SCMI protocol bus registered <6>[ 0.519675] vgaarb: loaded <6>[ 0.527926] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.547515] NET: Registered PF_INET protocol family <6>[ 0.553069] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.562557] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.571549] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.579879] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.588294] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.596380] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.603336] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.610532] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.618298] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.625039] RPC: Registered named UNIX socket transport module. <6>[ 0.631485] RPC: Registered udp transport module. <6>[ 0.636637] RPC: Registered tcp transport module. <6>[ 0.641806] RPC: Registered tcp-with-tls transport module. <6>[ 0.647766] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.654743] PCI: CLS 0 bytes, default 64 <5>[ 0.660460] Initialise system trusted keyrings <6>[ 0.665596] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.665962] Trying to unpack rootfs image as initramfs... <6>[ 0.673133] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.685127] NFS: Registering the id_resolver key type <5>[ 0.690714] Key type id_resolver registered <5>[ 0.695333] Key type id_legacy registered <6>[ 0.699819] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.707064] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.715486] Key type asymmetric registered <5>[ 0.720049] Asymmetric key parser 'x509' registered <6>[ 0.725527] bounce: pool size: 64 pages <6>[ 0.729856] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.737817] io scheduler mq-deadline registered <6>[ 0.742818] io scheduler kyber registered <6>[ 0.747284] io scheduler bfq registered <4>[ 0.773754] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.800489] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 0.829456] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 0.842457] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 0.925002] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.937433] printk: legacy console [ttyS0] disabled <6>[ 0.943212] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 70, base_baud = 25500000) is a Tegra <6>[ 0.952768] printk: legacy console [ttyS0] enabled <6>[ 0.952768] printk: legacy console [ttyS0] enabled <6>[ 0.963044] printk: legacy bootconsole [uart0] disabled <6>[ 0.963044] printk: legacy bootconsole [uart0] disabled <6>[ 0.976190] msm_serial: driver initialized <6>[ 0.981022] SuperH (H)SCI(F) driver initialized <6>[ 0.986156] STMicroelectronics ASC driver initialized <6>[ 0.991645] STM32 USART driver initialized <6>[ 0.997120] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 71, base_baud = 0) is a TEGRA_UART <6>[ 1.007149] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 72, base_baud = 0) is a TEGRA_UART <6>[ 1.020545] tegra-host1x 50000000.host1x: Adding to iommu group 0 <6>[ 1.037040] tegra-vic 54340000.vic: Adding to iommu group 1 <6>[ 1.056182] brd: module loaded <6>[ 1.066364] loop: module loaded <3>[ 1.120900] spi spi1.0: Invalid delay unit 2, should be SPI_DELAY_UNIT_SCK <3>[ 1.128069] spi-tegra114 7000da00.spi: can't setup spi1.0, status -22 <3>[ 1.134772] spi_master spi1: spi_device register error /spi@7000da00/flash@0 <4>[ 1.142111] spi_master spi1: Failed to create SPI device for /spi@7000da00/flash@0 <6>[ 1.156278] CAN device driver interface <6>[ 1.161710] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.169091] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.174314] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.180547] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.186203] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.197729] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.203619] usbcore: registered new interface driver pegasus <6>[ 1.209591] usbcore: registered new interface driver asix <6>[ 1.215282] usbcore: registered new interface driver ax88179_178a <6>[ 1.221695] usbcore: registered new interface driver cdc_ether <6>[ 1.227822] usbcore: registered new interface driver smsc75xx <6>[ 1.233879] usbcore: registered new interface driver smsc95xx <6>[ 1.239942] usbcore: registered new interface driver net1080 <6>[ 1.245892] usbcore: registered new interface driver cdc_subset <6>[ 1.252116] usbcore: registered new interface driver zaurus <6>[ 1.257997] usbcore: registered new interface driver cdc_ncm <4>[ 1.264499] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 1.272964] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 1.286207] usbcore: registered new interface driver usb-storage <6>[ 1.355303] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 1.360489] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 1.417948] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.10 <6>[ 1.424518] hub 1-0:1.0: USB hub found <6>[ 1.428595] hub 1-0:1.0: 1 port detected <6>[ 1.438854] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 1.444262] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 1.451448] i2c_dev: i2c /dev entries driver <4>[ 1.469800] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 1.477558] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 1.529691] i2c 4-0040: Fixed dependency cycle(s) with /i2c@7000d000/pmic@40/pinmux <6>[ 1.538662] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 1.552532] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 1.558201] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:16 UTC (946684816) <6>[ 1.567100] as3722-rtc as3722-rtc: RTC interrupt 101 <6>[ 1.575025] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 1.585470] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <4>[ 1.585788] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 1.598862] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 1.607123] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 1.614023] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <6>[ 1.614305] hwmon hwmon0: temp1_input not attached to any thermal zone <3>[ 1.621397] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 1.627645] hwmon hwmon0: temp2_input not attached to any thermal zone <3>[ 1.633428] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 1.661008] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.667453] sdhci: Copyright(c) Pierre Ossman <6>[ 1.674472] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.682883] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.694141] usbcore: registered new interface driver usbhid <6>[ 1.698362] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 1.700005] usbhid: USB HID core driver <6>[ 1.704988] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 1.714919] tegra-emc 7001b000.external-memory-controller: 64bit DRAM bus <6>[ 1.724245] tegra-emc 7001b000.external-memory-controller: OPP HW ver. 0x2, current clock rate 924 MHz <4>[ 1.735839] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 1.744788] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 (8000003f) counters available <6>[ 1.757592] NET: Registered PF_INET6 protocol family <6>[ 1.763919] Segment Routing with IPv6 <6>[ 1.767929] In-situ OAM (IOAM) with IPv6 <6>[ 1.772196] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.779043] NET: Registered PF_PACKET protocol family <6>[ 1.784356] can: controller area network core <6>[ 1.789043] NET: Registered PF_CAN protocol family <6>[ 1.794096] can: raw protocol <6>[ 1.797325] can: broadcast manager protocol <6>[ 1.801798] can: netlink gateway - max_hops=1 <5>[ 1.806791] Key type dns_resolver registered <6>[ 1.812876] ThumbEE CPU extension supported. <5>[ 1.817415] Registering SWP/SWPB emulation handler <5>[ 1.835697] Loading compiled-in X.509 certificates <3>[ 1.880390] as3722 4-0040: Failed to create device link (0x180) with regulator-3v3run <6>[ 1.892028] reg-fixed-voltage regulator-12v0sata: nonexclusive access to GPIO for (default) <6>[ 1.895995] tegra-dc 54200000.dc: Adding to iommu group 1 <4>[ 1.906346] Failed to attached device 54200000.dc to IOMMU_mapping <6>[ 1.914232] tegra-dc 54240000.dc: Adding to iommu group 1 <4>[ 1.919976] Failed to attached device 54240000.dc to IOMMU_mapping <6>[ 1.953548] ci_hdrc ci_hdrc.2: EHCI Host Controller <6>[ 1.958782] ci_hdrc ci_hdrc.2: new USB bus registered, assigned bus number 2 <6>[ 1.988001] ci_hdrc ci_hdrc.2: USB 2.0 started, EHCI 1.10 <6>[ 1.994539] hub 2-0:1.0: USB hub found <6>[ 1.998663] hub 2-0:1.0: 1 port detected <6>[ 2.012399] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <4>[ 2.019130] as3722-regulator as3722-regulator: DMA mask not set <6>[ 2.019287] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.033801] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.037103] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 2.040339] Freeing initrd memory: 17112K <6>[ 2.042245] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.047284] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 2.051486] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <3>[ 2.065317] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 2.073440] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.080528] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <3>[ 2.085696] tegra-pcie 1003000.pcie: failed to get PHY#0: -517 <6>[ 2.093466] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <3>[ 2.097682] tegra-pcie 1003000.pcie: failed to get PHYs: -517 <6>[ 2.105734] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <3>[ 2.110009] tegra-pcie 1003000.pcie: failed to request resources: -517 <6>[ 2.117186] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 2.140170] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <4>[ 2.153042] usb2-0: supply vbus not found, using dummy regulator <6>[ 2.154957] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <4>[ 2.159559] usb2-1: supply vbus not found, using dummy regulator <6>[ 2.175574] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.179336] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 2.182411] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.187342] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 2.195681] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.209037] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.217378] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.225837] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <4>[ 2.232258] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 2.239750] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 2.247924] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 2.278750] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 2.307696] mmc1: new high speed MMC card at address 0001 <6>[ 2.313944] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <6>[ 2.321975] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 2.327632] mmcblk1boot0: mmc1:0001 SEM16G 4.00 MiB <6>[ 2.333700] mmcblk1boot1: mmc1:0001 SEM16G 4.00 MiB <6>[ 2.339477] mmcblk1rpmb: mmc1:0001 SEM16G 4.00 MiB, chardev (236:0) <6>[ 2.696679] mmc0: new high speed SD card at address 0260 <6>[ 2.703584] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 2.712152] mmcblk0: p1 p2 <6>[ 3.472072] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 3.482466] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 3.489034] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 3.494790] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 3.501960] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 3.508477] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 3.515624] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 3.523678] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 PCIe Root Port <4>[ 3.531287] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 3.541271] pci 0000:00:02.0: PCI bridge to [bus 00] <6>[ 3.546515] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff] <6>[ 3.552932] pci 0000:00:02.0: enabling Extended Tags <6>[ 3.558278] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.569150] PCI: bus0: Fast back to back transfers disabled <6>[ 3.574990] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 3.583496] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint <6>[ 3.591059] pci 0000:01:00.0: BAR 0 [io 0x0000-0x00ff] <6>[ 3.596592] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00000fff 64bit] <6>[ 3.603364] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00003fff 64bit pref] <6>[ 3.610737] pci 0000:01:00.0: supports D1 D2 <6>[ 3.615273] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.637954] PCI: bus1: Fast back to back transfers disabled <6>[ 3.643784] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.650699] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]: assigned <6>[ 3.658483] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref]: assigned <6>[ 3.667190] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]: assigned <6>[ 3.674287] pci 0000:01:00.0: BAR 4 [mem 0x20000000-0x20003fff 64bit pref]: assigned <6>[ 3.682355] pci 0000:01:00.0: BAR 2 [mem 0x13000000-0x13000fff 64bit]: assigned <6>[ 3.689987] pci 0000:01:00.0: BAR 0 [io 0x1000-0x10ff]: assigned <6>[ 3.696359] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 3.701618] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 3.708015] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 3.715076] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <6>[ 3.723115] pci_bus 0000:00: resource 4 [mem 0x01000000-0x01001fff] <6>[ 3.729680] pci_bus 0000:00: resource 5 [io 0x0000-0xffff] <6>[ 3.735523] pci_bus 0000:00: resource 6 [mem 0x13000000-0x1fffffff] <6>[ 3.742079] pci_bus 0000:00: resource 7 [mem 0x20000000-0x3fffffff pref] <6>[ 3.749078] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] <6>[ 3.754920] pci_bus 0000:01: resource 1 [mem 0x13000000-0x130fffff] <6>[ 3.761477] pci_bus 0000:01: resource 2 [mem 0x20000000-0x200fffff 64bit pref] <4>[ 3.769027] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 3.776356] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 3.782877] pcieport 0000:00:02.0: PME: Signaling with IRQ 125 <6>[ 3.789395] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 3.847239] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 128 <6>[ 3.855623] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <4>[ 3.867292] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 3.875285] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 3.883157] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 3.891928] tegra-ahci 70027000.sata: AHCI vers 0001.0301, 32 command slots, 3 Gbps, platform mode <6>[ 3.901158] tegra-ahci 70027000.sata: 1/2 ports implemented (port mask 0x1) <6>[ 3.908423] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 3.918822] scsi host0: tegra-ahci <6>[ 3.923055] scsi host1: tegra-ahci <6>[ 3.926828] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 131 lpm-pol 0 <6>[ 3.935959] ata2: DUMMY <6>[ 3.939146] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.260715] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 4.272090] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 4.281678] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 4.318116] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver (mii_bus:phy_addr=r8169-0-100:00, irq=MAC) <6>[ 4.459007] r8169 0000:01:00.0 eth0: Link is Down <6>[ 6.044511] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <5>[ 6.078002] Sending DHCP requests ., OK <6>[ 7.372641] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.212 <6>[ 7.380718] IP-Config: Complete: <6>[ 7.384217] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.212, mask=255.255.255.0, gw=192.168.0.254 <6>[ 7.394864] host=192.168.0.212, domain=shed, nis-domain=(none) <6>[ 7.401411] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 7.401426] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 7.415357] clk: Disabling unused clocks <6>[ 7.419877] PM: genpd: Disabling unused power domains <6>[ 7.426535] Freeing unused kernel image (initmem) memory: 2048K <6>[ 7.432905] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.492050] udevd[145]: starting version 3.2.9 <5>[ 19.037933] random: crng init done <27>[ 19.044361] udevd[145]: specified user 'tss' unknown <27>[ 19.049769] udevd[145]: specified group 'tss' unknown <30>[ 19.056196] udevd[147]: starting eudev-3.2.9 <6>[ 19.189588] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <6>[ 19.234391] r8169 0000:01:00.0 enp1s0: renamed from eth0 (while UP) <6>[ 19.273963] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 101000 mC <6>[ 19.283713] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 101000 mC <4>[ 19.287445] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <6>[ 19.293883] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 101000 mC <3>[ 19.303449] tegra-xusb 70090000.usb: failed to request firmware: -2 <6>[ 19.313153] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 101000 mC <3>[ 19.319674] tegra-xusb 70090000.usb: failed to request firmware: -2 <6>[ 19.334960] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC <3>[ 19.335927] tegra-xusb 70090000.usb: probe with driver tegra-xusb failed with error -2 <6>[ 19.347514] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 101000 mC <6>[ 19.394245] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 19.457029] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub done Saving random seed: <6>[ 19.727571] input: NVIDIA Tegra Jetson TK1 Headphones Jack as /devices/soc0/sound/sound/card1/input2 OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3906641/environment / # /lava-3906641/bin/lava-test-runner /lava-3906641/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3906641/0/tests/0_dmesg + cat uuid + UUID=3906641_1.5<8>[ 20.366958] .2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 20.394479] <8>[ 20.424523] <8>[ 20.451067] + set +x <8>[ 20.460952] / #