connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='default', state=, avail=True, host='nuc-1', port=39083, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:39083 connected to 192.168.0.1 (port 39083) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.212 (8 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 3906643/tftp-deploy-x80orve8/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906643/tftp-deploy-x80orve8/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 2.5 MiB/s done Bytes transferred = 10789376 (a4a200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 3906643/tftp-deploy-x80orve8/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906643/tftp-deploy-x80orve8/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 2.4 MiB/s done Bytes transferred = 14336477 (dac1dd hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 3906643/tftp-deploy-x80orve8/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '3906643/tftp-deploy-x80orve8/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *###### 2.1 MiB/s done Bytes transferred = 73434 (11eda hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=192.168.0.2:/var/lib/lava/dispatcher/tmp/3906643/extract-nfsrootfs-4rjywmcy,tcp,hard,vers=3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0xa4a200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14336413 Bytes = 13.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f94ed9 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc6 (KernelCI@build-j361444-arm-gcc-12-multi-v7-defconfig-config-thumb2-k6bx7) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Mon Nov 4 03:05:40 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: legacy bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 17 pages/cpu s40844 r8192 d20596 u69632 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=192.168.0.2:/var/lib/lava/dispatcher/tmp/3906643/extract-nfsrootfs-4rjywmcy,tcp,hard,vers=3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524032 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.000000] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.000001] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.008576] Switching to timer-based delay loop, resolution 83ns <6>[ 0.015626] Console: colour dummy device 80x30 <6>[ 0.020558] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.031580] CPU: Testing write buffer coherency: ok <6>[ 0.036951] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.042563] CPU0: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.049419] pid_max: default: 32768 minimum: 301 <6>[ 0.054637] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.062492] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <3>[ 0.071615] /cpus/cpu@0 missing clock-frequency property <3>[ 0.077436] /cpus/cpu@1 missing clock-frequency property <3>[ 0.083276] /cpus/cpu@2 missing clock-frequency property <3>[ 0.089094] /cpus/cpu@3 missing clock-frequency property <6>[ 0.094897] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.102040] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.111318] rcu: Hierarchical SRCU implementation. <6>[ 0.116559] rcu: Max phase no-delay instances is 1000. <6>[ 0.122559] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.133521] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.142472] EFI services will not be available. <6>[ 0.147745] smp: Bringing up secondary CPUs ... <6>[ 0.153442] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.153461] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.170557] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.170576] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.187697] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.187716] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.204096] smp: Brought up 1 node, 4 CPUs <6>[ 0.208641] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.215324] CPU: All CPU(s) started in SVC mode. <6>[ 0.221040] Memory: 1971068K/2096128K available (11264K kernel code, 2543K rwdata, 6788K rodata, 2048K init, 430K bss, 56268K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.237909] devtmpfs: initialized <6>[ 0.258950] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.267400] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.277896] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.286783] pinctrl core: initialized pinctrl subsystem <6>[ 0.296231] DMI not present or invalid. <6>[ 0.301242] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.309921] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.321021] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.321083] cpuidle: using governor menu <6>[ 0.344785] platform 70000868.pinmux: Fixed dependency cycle(s) with /pinmux@70000868/pinmux <6>[ 0.379512] No ATAGs? <6>[ 0.382287] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.390878] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.413475] Serial: AMBA PL011 UART driver <3>[ 0.419360] tegra-mc 70019000.memory-controller: ppcsahbslvr: secure read @0x7fd41100: EMEM address decode error (EMEM decode error) <6>[ 0.450669] iommu: Default domain type: Translated <6>[ 0.455955] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.464423] SCSI subsystem initialized <6>[ 0.469086] usbcore: registered new interface driver usbfs <6>[ 0.475090] usbcore: registered new interface driver hub <6>[ 0.480942] usbcore: registered new device driver usb <6>[ 0.488124] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.493567] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.503341] PTP clock support registered <6>[ 0.507895] EDAC MC: Ver: 3.0.0 <6>[ 0.511802] scmi_core: SCMI protocol bus registered <6>[ 0.519590] vgaarb: loaded <6>[ 0.527914] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.547471] NET: Registered PF_INET protocol family <6>[ 0.553029] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.562507] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.571494] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.579822] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.588233] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.596317] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.603270] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.610462] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.618223] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.624965] RPC: Registered named UNIX socket transport module. <6>[ 0.631409] RPC: Registered udp transport module. <6>[ 0.636560] RPC: Registered tcp transport module. <6>[ 0.641726] RPC: Registered tcp-with-tls transport module. <6>[ 0.647686] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.654663] PCI: CLS 0 bytes, default 64 <5>[ 0.660374] Initialise system trusted keyrings <6>[ 0.665540] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.665911] Trying to unpack rootfs image as initramfs... <6>[ 0.673048] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.685056] NFS: Registering the id_resolver key type <5>[ 0.690630] Key type id_resolver registered <5>[ 0.695251] Key type id_legacy registered <6>[ 0.699734] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.706976] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.715533] Key type asymmetric registered <5>[ 0.720099] Asymmetric key parser 'x509' registered <6>[ 0.725520] bounce: pool size: 64 pages <6>[ 0.729841] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.737802] io scheduler mq-deadline registered <6>[ 0.742816] io scheduler kyber registered <6>[ 0.747284] io scheduler bfq registered <4>[ 0.773761] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.800389] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 0.829236] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 0.842227] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 0.924770] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.937206] printk: legacy console [ttyS0] disabled <6>[ 0.943014] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 70, base_baud = 25500000) is a Tegra <6>[ 0.952572] printk: legacy console [ttyS0] enabled <6>[ 0.952572] printk: legacy console [ttyS0] enabled <6>[ 0.962859] printk: legacy bootconsole [uart0] disabled <6>[ 0.962859] printk: legacy bootconsole [uart0] disabled <6>[ 0.976003] msm_serial: driver initialized <6>[ 0.980837] SuperH (H)SCI(F) driver initialized <6>[ 0.985972] STMicroelectronics ASC driver initialized <6>[ 0.991460] STM32 USART driver initialized <6>[ 0.996965] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 71, base_baud = 0) is a TEGRA_UART <6>[ 1.006984] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 72, base_baud = 0) is a TEGRA_UART <6>[ 1.020390] tegra-host1x 50000000.host1x: Adding to iommu group 0 <6>[ 1.036929] tegra-vic 54340000.vic: Adding to iommu group 1 <6>[ 1.055913] brd: module loaded <6>[ 1.066100] loop: module loaded <3>[ 1.120859] spi spi1.0: Invalid delay unit 2, should be SPI_DELAY_UNIT_SCK <3>[ 1.128024] spi-tegra114 7000da00.spi: can't setup spi1.0, status -22 <3>[ 1.134727] spi_master spi1: spi_device register error /spi@7000da00/flash@0 <4>[ 1.142089] spi_master spi1: Failed to create SPI device for /spi@7000da00/flash@0 <6>[ 1.156212] CAN device driver interface <6>[ 1.161657] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.169074] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.174296] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.180533] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.186190] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.197748] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.203643] usbcore: registered new interface driver pegasus <6>[ 1.209611] usbcore: registered new interface driver asix <6>[ 1.215300] usbcore: registered new interface driver ax88179_178a <6>[ 1.221709] usbcore: registered new interface driver cdc_ether <6>[ 1.227833] usbcore: registered new interface driver smsc75xx <6>[ 1.233891] usbcore: registered new interface driver smsc95xx <6>[ 1.239962] usbcore: registered new interface driver net1080 <6>[ 1.245913] usbcore: registered new interface driver cdc_subset <6>[ 1.252150] usbcore: registered new interface driver zaurus <6>[ 1.258033] usbcore: registered new interface driver cdc_ncm <4>[ 1.264507] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 1.272979] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 1.286203] usbcore: registered new interface driver usb-storage <6>[ 1.355310] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 1.360494] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 1.417933] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.10 <6>[ 1.424521] hub 1-0:1.0: USB hub found <6>[ 1.428602] hub 1-0:1.0: 1 port detected <6>[ 1.438893] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 1.444300] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 1.451481] i2c_dev: i2c /dev entries driver <4>[ 1.469557] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 1.477310] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 1.529528] i2c 4-0040: Fixed dependency cycle(s) with /i2c@7000d000/pmic@40/pinmux <6>[ 1.538546] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 1.554763] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 1.560917] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:16 UTC (946684816) <6>[ 1.569821] as3722-rtc as3722-rtc: RTC interrupt 101 <4>[ 1.587090] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 1.594077] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 1.596703] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 1.607372] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 1.626514] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.632998] sdhci: Copyright(c) Pierre Ossman <6>[ 1.640037] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.648457] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.659660] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 1.661132] usbcore: registered new interface driver usbhid <6>[ 1.664704] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 1.670483] usbhid: USB HID core driver <6>[ 1.684660] tegra-emc 7001b000.external-memory-controller: 64bit DRAM bus <6>[ 1.693955] tegra-emc 7001b000.external-memory-controller: OPP HW ver. 0x2, current clock rate 924 MHz <4>[ 1.705920] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 1.715281] Freeing initrd memory: 14004K <6>[ 1.716109] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 1.726741] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 (8000003f) counters available <6>[ 1.739516] NET: Registered PF_INET6 protocol family <6>[ 1.745630] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 1.753165] Segment Routing with IPv6 <6>[ 1.757163] In-situ OAM (IOAM) with IPv6 <6>[ 1.757313] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 1.761446] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.776104] NET: Registered PF_PACKET protocol family <6>[ 1.781435] can: controller area network core <6>[ 1.786096] NET: Registered PF_CAN protocol family <6>[ 1.791162] can: raw protocol <6>[ 1.794394] can: broadcast manager protocol <6>[ 1.798857] can: netlink gateway - max_hops=1 <5>[ 1.803807] Key type dns_resolver registered <6>[ 1.809861] ThumbEE CPU extension supported. <5>[ 1.814400] Registering SWP/SWPB emulation handler <5>[ 1.833368] Loading compiled-in X.509 certificates <6>[ 1.838050] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 1.846289] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <3>[ 1.854662] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 1.860649] as3722-regulator as3722-regulator: regulator 13 register failed -517 <3>[ 1.889676] as3722 4-0040: Failed to create device link (0x180) with regulator-3v3run <6>[ 1.901624] reg-fixed-voltage regulator-12v0sata: nonexclusive access to GPIO for (default) <6>[ 1.903532] tegra-dc 54200000.dc: Adding to iommu group 1 <4>[ 1.915989] Failed to attached device 54200000.dc to IOMMU_mapping <6>[ 1.923880] tegra-dc 54240000.dc: Adding to iommu group 1 <4>[ 1.929631] Failed to attached device 54240000.dc to IOMMU_mapping <6>[ 1.963468] ci_hdrc ci_hdrc.2: EHCI Host Controller <6>[ 1.968730] ci_hdrc ci_hdrc.2: new USB bus registered, assigned bus number 2 <6>[ 1.988069] ci_hdrc ci_hdrc.2: USB 2.0 started, EHCI 1.10 <6>[ 1.994697] hub 2-0:1.0: USB hub found <6>[ 1.998838] hub 2-0:1.0: 1 port detected <6>[ 2.010601] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 2.013891] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.015630] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 2.018997] as3722-regulator as3722-regulator: DMA mask not set <6>[ 2.022435] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <3>[ 2.028562] +VDDIO_SDMMC3: bypassed regulator has no supply! <6>[ 2.033584] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.043097] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 2.047812] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.058085] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 2.062833] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.073278] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 2.077632] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 2.087051] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <3>[ 2.092963] tegra-pcie 1003000.pcie: failed to get PHY#0: -517 <3>[ 2.110698] tegra-pcie 1003000.pcie: failed to get PHYs: -517 <3>[ 2.116718] tegra-pcie 1003000.pcie: failed to request resources: -517 <6>[ 2.139720] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <4>[ 2.152814] usb2-0: supply vbus not found, using dummy regulator <4>[ 2.159330] usb2-1: supply vbus not found, using dummy regulator <6>[ 2.167791] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 2.168807] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 2.174646] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 2.179607] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 2.187980] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 2.201247] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 2.209664] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 2.218139] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <4>[ 2.224396] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 2.230379] mmc1: new high speed MMC card at address 0001 <6>[ 2.231656] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 2.236757] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <6>[ 2.244793] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 2.256413] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 2.262865] mmcblk1boot0: mmc1:0001 SEM16G 4.00 MiB <6>[ 2.268894] mmcblk1boot1: mmc1:0001 SEM16G 4.00 MiB <6>[ 2.274782] mmcblk1rpmb: mmc1:0001 SEM16G 4.00 MiB, chardev (236:0) <6>[ 2.283857] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 2.705140] mmc0: new high speed SD card at address 0260 <6>[ 2.712806] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 2.722573] mmcblk0: p1 p2 <6>[ 3.462058] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 3.472558] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 3.479117] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 3.484860] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 3.492011] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 3.498461] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 3.505594] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 3.513504] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 PCIe Root Port <4>[ 3.521088] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 3.531030] pci 0000:00:02.0: PCI bridge to [bus 00] <6>[ 3.536258] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff] <6>[ 3.542638] pci 0000:00:02.0: enabling Extended Tags <6>[ 3.547934] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.558531] PCI: bus0: Fast back to back transfers disabled <6>[ 3.564361] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 3.572787] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint <6>[ 3.580311] pci 0000:01:00.0: BAR 0 [io 0x0000-0x00ff] <6>[ 3.585824] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00000fff 64bit] <6>[ 3.592553] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00003fff 64bit pref] <6>[ 3.599869] pci 0000:01:00.0: supports D1 D2 <6>[ 3.604397] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 3.628287] PCI: bus1: Fast back to back transfers disabled <6>[ 3.634200] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.641167] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]: assigned <6>[ 3.648915] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref]: assigned <6>[ 3.657603] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]: assigned <6>[ 3.664647] pci 0000:01:00.0: BAR 4 [mem 0x20000000-0x20003fff 64bit pref]: assigned <6>[ 3.672654] pci 0000:01:00.0: BAR 2 [mem 0x13000000-0x13000fff 64bit]: assigned <6>[ 3.680227] pci 0000:01:00.0: BAR 0 [io 0x1000-0x10ff]: assigned <6>[ 3.686571] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 3.691789] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 3.698136] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 3.705170] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <6>[ 3.713164] pci_bus 0000:00: resource 4 [mem 0x01000000-0x01001fff] <6>[ 3.719680] pci_bus 0000:00: resource 5 [io 0x0000-0xffff] <6>[ 3.725499] pci_bus 0000:00: resource 6 [mem 0x13000000-0x1fffffff] <6>[ 3.732016] pci_bus 0000:00: resource 7 [mem 0x20000000-0x3fffffff pref] <6>[ 3.738966] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] <6>[ 3.744785] pci_bus 0000:01: resource 1 [mem 0x13000000-0x130fffff] <6>[ 3.751302] pci_bus 0000:01: resource 2 [mem 0x20000000-0x200fffff 64bit pref] <4>[ 3.758790] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 3.766048] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 3.772463] pcieport 0000:00:02.0: PME: Signaling with IRQ 127 <6>[ 3.778711] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 3.831476] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 130 <6>[ 3.839869] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <4>[ 3.849589] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 3.857495] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 3.865343] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 3.874244] tegra-ahci 70027000.sata: AHCI vers 0001.0301, 32 command slots, 3 Gbps, platform mode <6>[ 3.883488] tegra-ahci 70027000.sata: 1/2 ports implemented (port mask 0x1) <6>[ 3.890729] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 3.901215] scsi host0: tegra-ahci <6>[ 3.905531] scsi host1: tegra-ahci <6>[ 3.909373] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 131 lpm-pol 0 <6>[ 3.918501] ata2: DUMMY <6>[ 3.922094] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.241062] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 4.251165] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 4.260639] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 4.298174] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver (mii_bus:phy_addr=r8169-0-100:00, irq=MAC) <6>[ 4.438892] r8169 0000:01:00.0 eth0: Link is Down <6>[ 6.028528] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <5>[ 6.057914] Sending DHCP requests ., OK <6>[ 6.102368] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.212 <6>[ 6.110471] IP-Config: Complete: <6>[ 6.113960] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.212, mask=255.255.255.0, gw=192.168.0.254 <6>[ 6.124569] host=192.168.0.212, domain=shed, nis-domain=(none) <6>[ 6.131108] bootserver=192.168.0.1, rootserver=192.168.0.2, rootpath= <6>[ 6.131115] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 6.144854] clk: Disabling unused clocks <6>[ 6.149224] PM: genpd: Disabling unused power domains <6>[ 6.155537] Freeing unused kernel image (initmem) memory: 2048K <6>[ 6.161890] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.22-1~deb12u1 <6>[ 6.619926] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <6>[ 6.644320] r8169 0000:01:00.0 enp1s0: renamed from eth0 (while UP) <4>[ 6.695876] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 6.705891] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 6.712423] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 6.718999] tegra-xusb 70090000.usb: probe with driver tegra-xusb failed with error -2 <6>[ 6.731216] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 101000 mC <6>[ 6.740981] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 101000 mC <6>[ 6.755474] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 101000 mC <6>[ 6.765229] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 101000 mC <6>[ 6.775318] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC <6>[ 6.785896] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 101000 mC <6>[ 6.815677] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 6.890302] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub <6>[ 7.161701] input: NVIDIA Tegra Jetson TK1 Headphones Jack as /devices/soc0/sound/sound/card1/input2 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/enp1s0 found done. Begin: Waiting up to 180 secs for eth0 to become available ... <6>[ 36.418569] +1.8V_RUN_CAM: disabling <6>[ 36.422824] +2.8V_RUN_CAM: disabling <6>[ 36.427008] +1.2V_RUN_CAM_FRONT: disabling <6>[ 36.431887] +1.05V_RUN_CAM_REAR: disabling <6>[ 36.436627] +3.3V_RUN_TOUCH: disabling <6>[ 36.441105] +2.8V_RUN_CAM_AF: disabling <6>[ 36.445355] +1.8V_RUN_VPP_FUSE: disabling <4>[ 69.698518] tegra-emc 7001b000.external-memory-controller: sync_state() pending due to 54200000.dc <4>[ 69.707813] tegra-mc 70019000.memory-controller: sync_state() pending due to 54200000.dc <4>[ 69.716297] tegra-emc 7001b000.external-memory-controller: sync_state() pending due to 54240000.dc <4>[ 69.725698] tegra-mc 70019000.memory-controller: sync_state() pending due to 54240000.dc # # Failure: Network device did not appear in time done. ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such device ipconfig: no devices to configure ipconfig: eth0: SIOCGIFINDEX: No such de<0>[ 188.906503] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 vice ipconfig: no devices to co<4>[ 188.917326] CPU: 1 UID: 0 PID: 1 Comm: init Not tainted 6.12.0-rc6 #1 nfigure /init: <4>[ 188.926780] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) 380: .: Can<'4>t[ 1o8p8.934683] Call trace: <4>[ 188.934701] unwind_backtrace from show_stack+0xb/0xc <4>[ 188.944204] show_stack from panic+0xc3/0x2a4 <4>[ 188.948842] panic from make_task_dead+0x1/0x114 <4>[ 188.953731] make_task_dead from 0x0 <0>[ 188.957642] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 ]---