connecting to NetworkSerialPort(target=Target(name='meson-g12a-u200', env=None), name='USBSerialPort', state=, avail=True, host='nuc-2', port=42045, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-2:42045 connected to 192.168.0.2 (port 42045) Escape character: Ctrl-\ Type the escape character to get to the prompt. G12A:BL:583440:b596c7;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0; bl2_stage_init1 L0:00000000 L1:80000703 L2:00008067 L3:04000000 B2:00002000 B1:e0f83180 TE: 140803 BL2 Built : 21:12:49, Apr 28 2018. g12a g3a251ca - jenkins@walle02-sh Board ID = 1 Set cpu clk to 24M Set clk81 to 24M CPU clk: 1200 MHz Set clk81 to 166.6M Handler is not supported boot_device: 1 -s board id: 1 Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x004000, part: 0 fw parse done Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x004000, part: 0 Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x004000, part: 0 PIEI prepare done Cfg max: 4, cur: 1. Board id: 255. Force loop cfg DDR4 probe Set ddr clk to 912MHz Load ddrfw from eMMC, src: 0x00014200, des: 0xfffd0000, size: 0x00c000, part: 0 dfi pinmux init ac pinmux init Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of Write leveling coarse delay INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from eMMC, src: 0x00020200, des: 0xfffd0000, size: 0x00c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! R0_RxClkDly_Margin==205 R0_TxDqDly_Margi==222 R1_RxClkDly_Margin==0 R1_TxDqDly_Margi==0 PIEI init PIEI init cnt: 180 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001 2D training succeed DDR size: 2048MB DataBus test pass! AddrBus test pass! result report Enable ddr reg access 00000000 emmc switch 3 ok Authentication key not yet programmed emmc_rpmb_key_is_programmed: error 0x00000007 00000000 emmc switch 0 ok Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x004000, part: 0 Load BL3X from eMMC, src: 0x00064200, des: 0x01754000, size: 0x0b4000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 [Image: g12a_v1.1.3310-81c9e20 2018-05-02 10:15:01 jenkins@walle02-sh] OPS=0x10 28 0a 10 00 6c 5f 6c 59 2d 41 32 31 47 4c 4d 41 This is ES chip bl30:This chip has not trimmed thermal!!! bl30: thermal cali data update error [0.020913 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):debc425 NOTICE: BL31: Built : 14:06:49, May 3 2018 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2015.01-g784ee4d (May 04 2018 - 20:08:53) DRAM: 2 GiB Relocation Offset is: 76e83000 spi_post_bind(spifc): req_seq = 0 register usb cfg[0][1] = 0000000077f48578 NAND: get_sys_clk_rate_mtd() 266, clock setting 200! NAND device id: 0 7 ff ff ff ff No NAND device found!!! nand init failed: -6 get_sys_clk_rate_mtd() 266, clock setting 200! NAND device id: 0 7 ff ff ff ff No NAND device found!!! nand init failed: -6 MMC: aml_priv->desc_buf = 0x0000000073e73710 aml_priv->desc_buf = 0x0000000073e75a30 SDIO Port B: 0, SDIO Port C: 1 co-phase 0x2, tx-dly 0 co-phase 0x2, tx-dly 0 co-phase 0x2, tx-dly 0 emmc/sd response timeout, cmd8, status=0x1ff2800 emmc/sd response timeout, cmd55, status=0x1ff2800 co-phase 0x2, tx-dly 0 co-phase 0x2, tx-dly 0 init_part() 297: PART_TYPE_AML [mmc_init] mmc init success start dts,buffer=0000000073e78280,dt_addr=0000000073e78280 get_partition_from_dts() 105: ret 0 parts: 14 00: logo 0000000000800000 1 01: recovery 0000000001800000 1 02: misc 0000000000800000 1 03: dto 0000000000800000 1 04: cri_data 0000000000800000 2 05: param 0000000001000000 2 06: boot 0000000001000000 1 07: rsv 0000000001000000 1 08: tee 0000000002000000 1 09: vendor 0000000010000000 1 10: odm 0000000010000000 1 11: system 0000000074000000 1 12: cache 0000000046000000 2 13: data ffffffffffffffff 4 init_part() 297: PART_TYPE_AML eMMC/TSD partition table have been checked OK! check pattern success mmc env offset: 0x4d400000 In: serial Out: serial Err: serial reboot_mode=cold_boot [store]To run cmd[emmc dtb_read 0x1000000 0x40000] _verify_dtb_checksum()-2755: calc c2806ee9, store c2806ee9 _verify_dtb_checksum()-2755: calc c2806ee9, store c2806ee9 dtb_read()-2972: total valid 2 update_old_dtb()-2953: do nothing amlkey_init() enter! [EFUSE_MSG]keynum is 4 vpu: clk_level in dts: 7 vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100) vpu: vpu_clk_gate_init_off finish vpp: vpp_init vpp: g12a osd1 matrix rgb2yuv .............. vpp: g12a osd2 matrix rgb2yuv.............. vpp: g12a osd3 matrix rgb2yuv.............. aml_config_dtb 572 aml_config_dtb 574 co_phase = <0x00000002> libfdt fdt_getprop(): FDT_ERR_NOTFOUND f_max = <0x02625a00> status = "okay" status = "okay" drive-strength = <0x00000001> drive-strength = <0x00000001> drive-strength = <0x00000001> drive-strength = <0x00000001> drive-strength = <0x00000002> drive-strength = <0x00000001> Net: dwmac.ff3f0000amlkey_init() enter! amlkey_init() 71: already init! [EFUSE_MSG]keynum is 4 MACADDR:02:2d:59:6c:5f:6c(from chipid) Start read misc partition datas! info->attemp_times = 0 info->active_slot = 0 info->slot_info[0].bootable = 1 info->slot_info[0].online = 1 info->slot_info[1].bootable = 0 info->slot_info[1].online = 0 info->attemp_times = 0 attemp_times = 0 active slot = 0 wipe_data=successful wipe_cache=successful upgrade_step=0 [OSD]load fb addr from dts:/meson-fb [OSD]set initrd_high: 0x7f800000 [OSD]fb_addr for logo: 0x7f800000 [OSD]load fb addr from dts:/meson-fb [OSD]fb_addr for logo: 0x7f800000 [OSD]VPP_OFIFO_SIZE:0xfff01fff [CANVAS]canvas init [CANVAS]addr=0x7f800000 width=3840, height=2160 [OSD]osd_hw.free_dst_data: 0,1919,0,1079 [OSD]osd1_update_disp_freescale_enable [1080p60hz] is invalid for cvbs. set hdmitx VIC = 16 config HPLL = 4455000 HPLL: 0x3b0004b9 HPLL: 0x1b0004b9 HPLL: 0xdb0004b9 config HPLL done j = 6 vid_clk_div = 1 hdmitx phy setting done hdmitx: set enc for VIC: 16 enc_vpu_bridge_reset[1195] rx version is 1.4 or below div=10 amlkey_init() enter! amlkey_init() 71: already init! [EFUSE_MSG]keynum is 4 [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet [KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet Hit Enter or space or Ctrl+C key to stop autoboot -- : 1  0 g12a_u200_v1#setenv autoload no g12a_u200_v1#setenv initrd_high 0xffffffff g12a_u200_v1#setenv fdt_high 0xffffffff g12a_u200_v1#dhcp dwmac.ff3f0000 Waiting for PHY auto negotiation to complete.. done Speed: 100, full duplex BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.0.194 (261 ms) g12a_u200_v1#setenv serverip 192.168.0.2 g12a_u200_v1#tftp 0x8080000 3894888/tftp-deploy-xqumvjj0/kernel/uImage Speed: 100, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.194 Filename '3894888/tftp-deploy-xqumvjj0/kernel/uImage'. Load address: 0x8080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################################################### 1.9 MiB/s done Bytes transferred = 45603392 (2b7da40 hex) g12a_u200_v1#tftp 0x13000000 3894888/tftp-deploy-xqumvjj0/ramdisk/ramdisk.cpio.gz.uboot Speed: 100, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.194 Filename '3894888/tftp-deploy-xqumvjj0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x13000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 1.9 MiB/s done Bytes transferred = 25984764 (18c7efc hex) g12a_u200_v1#setenv initrd_size ${filesize} g12a_u200_v1#tftp 0x8008000 3894888/tftp-deploy-xqumvjj0/dtb/meson-g12a-u200.dtb Speed: 100, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.194 Filename '3894888/tftp-deploy-xqumvjj0/dtb/meson-g12a-u200.dtb'. Load address: 0x8008000 Loading: *#### 1.6 MiB/s done Bytes transferred = 52497 (cd11 hex) g12a_u200_v1#setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' g12a_u200_v1#bootm 0x8080000 0x13000000 0x8008000 ee_gate_off ... ## Booting kernel from Legacy Image at 08080000 ... Image Name: Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 45603328 Bytes = 43.5 MiB Load Address: 08080000 Entry Point: 08080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 25984700 Bytes = 24.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK load dtb from 0x1000000 ...... ## Flattened Device Tree blob at 08008000 Booting using the fdt blob at 0x8008000 Loading Kernel Image(COMP_NONE) ... OK kernel loaded at 0x08080000, end = 0x0abfda00 libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND [rsvmem] fdt get prop fail. Loading Ramdisk to 725a9000, end 73e70ebc ... OK Loading Device Tree to 0000000072599000, end 00000000725a8d10 ... OK Starting kernel ... uboot time: 41926760 us [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.11.0-rc5-next-20240830 (KernelCI@build-j301524-arm64-gcc-12-defconfig-config-randomize-basevh5bh) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Aug 30 07:50:48 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Amlogic Meson G12A U200 Development Board [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000062400000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: 0x0000000062400000..0x00000000723fffff (262144 KiB) map reusable linux,cma [ 0.000000] OF: reserved mem: 0x0000000005000000..0x00000000052fffff (3072 KiB) nomap non-reusable secmon@5000000 [ 0.000000] OF: reserved mem: 0x0000000005300000..0x00000000072fffff (32768 KiB) nomap non-reusable secmon@5300000 [ 0.000000] earlycon: meson0 at MMIO 0x00000000ff803000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [meson0] enabled [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x0000000077ffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x77bfad80-0x77bfd3bf] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000077ffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000004ffffff] [ 0.000000] node 0: [mem 0x0000000005000000-0x00000000072fffff] [ 0.000000] node 0: [mem 0x0000000007300000-0x0000000077ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000077ffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 25 pages/cpu s61656 r8192 d32552 u102400 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 491520 <6>[ 0.000000] Policy zone: DMA <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB <6>[ 0.000000] software IO TLB: area num 4. <6>[ 0.000000] software IO TLB: mapped [mem 0x0000000075700000-0x0000000075900000] (2MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.008791] Console: colour dummy device 80x25 <6>[ 0.013136] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) <6>[ 0.023631] pid_max: default: 32768 minimum: 301 <6>[ 0.028600] LSM: initializing lsm=capability <6>[ 0.033206] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.040788] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.069027] rcu: Hierarchical SRCU implementation. <6>[ 0.069071] rcu: Max phase no-delay instances is 1000. <6>[ 0.074175] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.086463] EFI services will not be available. <6>[ 0.090491] smp: Bringing up secondary CPUs ... <6>[ 0.092581] Detected VIPT I-cache on CPU1 <6>[ 0.092714] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.093397] Detected VIPT I-cache on CPU2 <6>[ 0.093477] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] <6>[ 0.094076] Detected VIPT I-cache on CPU3 <6>[ 0.094140] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] <6>[ 0.094253] smp: Brought up 1 node, 4 CPUs <6>[ 0.129720] SMP: Total of 4 processors activated. <6>[ 0.134694] CPU: All CPU(s) started at EL2 <6>[ 0.139108] CPU features: detected: 32-bit EL0 Support <6>[ 0.144497] CPU features: detected: 32-bit EL1 Support <6>[ 0.149931] CPU features: detected: CRC32 instructions <6>[ 0.155384] alternatives: applying system-wide alternatives <6>[ 0.162560] Memory: 1551516K/1966080K available (17216K kernel code, 4918K rwdata, 11840K rodata, 10432K init, 742K bss, 148008K reserved, 262144K cma-reserved) <6>[ 0.177016] devtmpfs: initialized <6>[ 0.189858] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.194298] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.208289] 21424 pages in range for non-PLT usage <6>[ 0.208313] 512944 pages in range for PLT usage <6>[ 0.208574] pinctrl core: initialized pinctrl subsystem <6>[ 0.221125] DMI not present or invalid. <6>[ 0.224660] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.229694] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.236478] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.244717] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.252570] audit: initializing netlink subsys (disabled) <5>[ 0.257998] audit: type=2000 audit(0.176:1): state=initialized audit_enabled=0 res=1 <6>[ 0.260355] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.265757] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.272124] cpuidle: using governor menu <6>[ 0.283344] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.290261] ASID allocator initialised with 65536 entries <6>[ 0.298665] Serial: AMBA PL011 UART driver <6>[ 0.312020] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.333228] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.335992] platform ff900000.vpu: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0 <6>[ 0.351860] platform ff900000.vpu: Fixed dependency cycle(s) with /cvbs-connector <6>[ 0.354087] platform cvbs-connector: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.362721] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /hdmi-connector <6>[ 0.370354] platform hdmi-connector: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0 <6>[ 0.384275] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.386371] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.392954] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.400026] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.406590] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.413676] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.420240] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.427327] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.436100] ACPI: Interpreter disabled. <6>[ 0.441523] iommu: Default domain type: Translated <6>[ 0.443095] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.449929] SCSI subsystem initialized <6>[ 0.453952] usbcore: registered new interface driver usbfs <6>[ 0.459384] usbcore: registered new interface driver hub <6>[ 0.464978] usbcore: registered new device driver usb <6>[ 0.471718] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.475544] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.485002] PTP clock support registered <6>[ 0.489322] EDAC MC: Ver: 3.0.0 <6>[ 0.493327] scmi_core: SCMI protocol bus registered <6>[ 0.499069] FPGA manager framework <6>[ 0.501525] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.508957] vgaarb: loaded <6>[ 0.511360] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.517475] VFS: Disk quotas dquot_6.6.0 <6>[ 0.521412] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.528827] pnp: PnP ACPI: disabled <6>[ 0.539501] NET: Registered PF_INET protocol family <6>[ 0.539716] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.548258] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) <6>[ 0.555614] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.563616] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.571936] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear) <6>[ 0.579836] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 0.586391] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 0.593323] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 0.600864] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.607104] RPC: Registered named UNIX socket transport module. <6>[ 0.612872] RPC: Registered udp transport module. <6>[ 0.617851] RPC: Registered tcp transport module. <6>[ 0.622837] RPC: Registered tcp-with-tls transport module. <6>[ 0.628613] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.635367] PCI: CLS 0 bytes, default 64 <6>[ 0.639736] Unpacking initramfs... <6>[ 0.647407] kvm [1]: nv: 552 coarse grained trap handlers <6>[ 0.649402] kvm [1]: IPA Size Limit: 40 bits <6>[ 0.655872] kvm [1]: vgic interrupt IRQ9 <6>[ 0.657705] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 0.665205] Initialise system trusted keyrings <6>[ 0.668562] workingset: timestamp_bits=42 max_order=19 bucket_order=0 <6>[ 0.675472] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.681583] NFS: Registering the id_resolver key type <5>[ 0.686523] Key type id_resolver registered <5>[ 0.690942] Key type id_legacy registered <6>[ 0.695286] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.702230] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.710218] 9p: Installing v9fs 9p2000 file system support <5>[ 0.769015] Key type asymmetric registered <5>[ 0.769076] Asymmetric key parser 'x509' registered <6>[ 0.773050] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.780629] io scheduler mq-deadline registered <6>[ 0.785433] io scheduler kyber registered <6>[ 0.789784] io scheduler bfq registered <6>[ 0.796407] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized <6>[ 0.858555] soc soc0: Amlogic Meson G12A (S905D2) Revision 28:a (10:2) Detected <6>[ 0.875733] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled�<6>[ 0.882506] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart <6>[ 0.892325] printk: legacy console [ttyAML0] enabled <6>[ 0.892325] printk: legacy console [ttyAML0] enabled <6>[ 0.897154] printk: legacy bootconsole [meson0] disabled <6>[ 0.897154] printk: legacy bootconsole [meson0] disabled <6>[ 0.912532] msm_serial: driver initialized <6>[ 0.913232] SuperH (H)SCI(F) driver initialized <6>[ 0.917889] STM32 USART driver initialized <5>[ 0.925099] random: crng init done <6>[ 0.932933] loop: module loaded <6>[ 0.934823] megasas: 07.727.03.00-rc1 <6>[ 0.944994] tun: Universal TUN/TAP device driver, 1.6 <6>[ 0.946735] thunder_xcv, ver 1.0 <6>[ 0.948245] thunder_bgx, ver 1.0 <6>[ 0.951698] nicpf, ver 1.0 <6>[ 0.957206] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 0.962062] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 0.967691] hclge is initializing <6>[ 0.971175] e1000: Intel(R) PRO/1000 Network Driver <6>[ 0.976253] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 0.982317] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 0.987429] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 0.993651] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 0.999261] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.005154] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.011537] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.018737] sky2: driver version 1.30 <6>[ 1.024480] VFIO - User Level meta-driver version: 0.3 <6>[ 1.032542] usbcore: registered new interface driver usb-storage <6>[ 1.038904] i2c_dev: i2c /dev entries driver <3>[ 1.049990] amlogic_thermal ff634800.temperature-sensor: tsensor thermal calibration not supported: 0x0! <3>[ 1.054148] amlogic_thermal ff634800.temperature-sensor: probe with driver amlogic_thermal failed with error -22 <3>[ 1.065534] amlogic_thermal ff634c00.temperature-sensor: tsensor thermal calibration not supported: 0x0! <3>[ 1.074271] amlogic_thermal ff634c00.temperature-sensor: probe with driver amlogic_thermal failed with error -22 <6>[ 1.092535] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.093355] sdhci: Copyright(c) Pierre Ossman <6>[ 1.100060] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.106920] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.106956] meson-gx-mmc ffe05000.mmc: Got CD GPIO <6>[ 1.115861] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.124247] meson-sm: secure-monitor enabled <6>[ 1.128278] usbcore: registered new interface driver usbhid <6>[ 1.131695] usbhid: USB HID core driver <6>[ 1.152498] NET: Registered PF_PACKET protocol family <6>[ 1.152638] 9pnet: Installing 9P2000 support <5>[ 1.156837] Key type dns_resolver registered <6>[ 1.171766] registered taskstats version 1 <5>[ 1.171952] Loading compiled-in X.509 certificates <6>[ 1.183472] Demotion targets for Node 0: null <6>[ 1.246190] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2 <6>[ 1.246242] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1 <4>[ 1.257089] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.259013] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.266688] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM <6>[ 1.278217] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.279266] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 1.287384] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000808000000010 <6>[ 1.296841] xhci-hcd xhci-hcd.0.auto: irq 20, io mem 0xff500000 <6>[ 1.303111] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.308673] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 1.316560] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 1.324205] hub 1-0:1.0: USB hub found <6>[ 1.327395] hub 1-0:1.0: 2 ports detected <6>[ 1.332031] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 1.340605] hub 2-0:1.0: USB hub found <6>[ 1.343893] hub 2-0:1.0: 1 port detected <6>[ 1.349044] dwc3-meson-g12a ffe09000.usb: switching to Device Mode <6>[ 1.363156] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq <6>[ 1.541031] mmc1: new HS200 MMC card at address 0001 <6>[ 1.541921] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB <6>[ 1.547973] mmcblk1boot0: mmc1:0001 AJTD4R 4.00 MiB <6>[ 1.552113] mmcblk1boot1: mmc1:0001 AJTD4R 4.00 MiB <6>[ 1.557237] mmcblk1rpmb: mmc1:0001 AJTD4R 4.00 MiB, chardev (511:0) <6>[ 1.861023] Freeing initrd memory: 25372K <6>[ 13.667458] clk: Disabling unused clocks <6>[ 13.667705] PM: genpd: Disabling unused power domains <6>[ 13.671337] ALSA device list: <6>[ 13.674529] No soundcards found. <6>[ 13.687762] Freeing unused kernel memory: 10432K <6>[ 13.687882] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 13.766156] udevd[107]: starting version 3.2.9 <27>[ 13.771645] udevd[107]: specified user 'tss' unknown <27>[ 13.771764] udevd[107]: specified group 'tss' unknown <30>[ 13.778417] udevd[108]: starting eudev-3.2.9 <6>[ 14.118954] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found <6>[ 14.139435] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found <6>[ 14.140267] meson8b-dwmac ff3f0000.ethernet: IRQ sfty not found <6>[ 14.152913] mc: Linux media interface: v0.10 <6>[ 14.173230] videodev: Linux video capture interface: v2.00 <6>[ 14.175823] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock <6>[ 14.191486] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37 <6>[ 14.193268] meson8b-dwmac ff3f0000.ethernet: DWMAC1000 <6>[ 14.237676] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported <6>[ 14.243473] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported <6>[ 14.247606] meson8b-dwmac ff3f0000.ethernet: COE Type 2 <6>[ 14.253007] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported <6>[ 14.260281] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported <6>[ 14.272780] panfrost ffe40000.gpu: clock rate = 24000000 <3>[ 14.272919] panfrost ffe40000.gpu: error -ENODEV: _opp_set_regulators: no regulator (mali) found <6>[ 14.275699] meson8b-dwmac ff3f0000.ethernet: Normal descriptors <6>[ 14.292195] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled <6>[ 14.293967] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 14.305930] panfrost ffe40000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0 <6>[ 14.310298] panfrost ffe40000.gpu: features: 00000000,000027f7, issues: 00000000,00000400 <6>[ 14.318669] panfrost ffe40000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7 <6>[ 14.330692] panfrost ffe40000.gpu: shader_present=0x1 l2_present=0x1 <4>[ 14.350911] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned. <6>[ 14.365966] meson-drm ff900000.vpu: Queued 2 outputs on vpu <6>[ 14.390906] meson-vrtc ff8000a8.rtc: registered as rtc0 <6>[ 14.390992] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:14 UTC (14) <6>[ 14.402544] [drm] Initialized panfrost 1.2.0 for ffe40000.gpu on minor 0 <3>[ 14.425153] debugfs: Directory 'ff800280.cec' with parent 'regmap' already present! <6>[ 14.432393] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy) <6>[ 14.440186] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver <4>[ 14.444642] meson-pwm ff802000.pwm: using obsolete compatible, please consider updating dt <6>[ 14.456899] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops [meson_dw_hdmi]) <3>[ 14.463529] meson-drm ff900000.vpu: DSI transceiver device is disabled <6>[ 14.468310] Registered IR keymap rc-empty <6>[ 14.486918] rc rc0: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0 <6>[ 14.490789] [drm] Initialized meson 1.0.0 for ff900000.vpu on minor 1 <6>[ 14.490794] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0/input0 <6>[ 14.516004] rc rc0: sw decoder init <6>[ 14.516075] meson-ir ff808000.ir: receiver initialized <6>[ 14.527390] Console: switching to colour frame buffer device 90x36 <6>[ 14.564137] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device done Saving random seed: OK Starting network: OK Starting dropbear sshd: <6>[ 14.817146] NET: Registered PF_INET6 protocol family <6>[ 14.817967] Segment Routing with IPv6 <6>[ 14.820688] In-situ OAM (IOAM) with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3894888/environment / # /lava-3894888/bin/lava-test-runner /lava-3894888/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3894888/0/tests/0_dmesg + cat uuid + UUID=3894888_1.5.<8>[ 15.362563] 2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.390512] <8>[ 15.413205] <8>[ 15.434937] + set +x <8>[ 15.438862] / #