connecting to NetworkSerialPort(target=Target(name='meson-sm1-khadas-vim3l', env=None), name='USBSerialPort', state=, avail=True, host='nuc-2', port=51883, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-2:51883 connected to 192.168.0.2 (port 51883) Escape character: Ctrl-\ Type the escape character to get to the prompt. SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;CHK:1F;READ:0;0.0;CHK:0; bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02 L0:00000000 L1:00000703 L2:00008067 L3:15000000 S1:00000000 B2:20282000 B1:a0f83180 TE: 194189 BL2 Built : 15:59:24, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz Board ID = 8 Set cpu clk to 24M Set clk81 to 24M Use GP1_pll as DSU clk. DSU clk: 1200 Mhz CPU clk: 1200 MHz Set clk81 to 166.6M eMMC boot @ 1 sw8 s board id: 8 Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 1 fw parse done PIEI prepare done ddr saved addr:00016000 Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0 00000000 emmc switch 0 ok fastboot data verify result: 255 Cfg max: 12, cur: 1. Board id: 255. Force loop cfg LPDDR4 probe LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz ddr clk to 1608MHz 00000000 emmc switch 1 ok dmc_version 0001 Check phy result INFO : ERROR : Training has failed! Check phy result INFO : ERROR : Training has failed! Check phy result INFO : End of initialization INFO : ERROR : Training has failed! 1D training failed Cfg max: 12, cur: 2. Board id: 255. Force loop cfg LPDDR4 probe ddr clk to 1608MHz dmc_version 0001 Check phy result INFO : End of CA training INFO : End of initialization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of Write leveling coarse delay INFO : End of read delay center optimization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of MPR read delay center optimization INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! soc_vref_reg_value 0x 00000025 00000027 00000024 00000027 00000024 00000026 00000024 00000025 00000026 00000024 00000028 00000027 00000026 00000026 00000026 00000025 00000024 00000025 00000023 00000022 00000022 00000025 00000024 00000024 00000024 00000023 00000027 00000026 00000025 00000024 00000023 00000025 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004 dram_vref_reg_value 0x 00000014 2D training succeed auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 0MB DMC_DDR_CTRL: 00c0002cDDR size: 2048MB cs0 DataBus test pass cs0 AddrBus test pass non-sec scramble use zero key ddr scramble enabled 100bdlr_step_size ps== 431 result report boot times 0Enable ddr reg access 00000000 emmc switch 3 ok Authentication key not yet programmed get rpmb counter error 0x00000007 00000000 emmc switch 1 ok Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 1 Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000ac200, part: 1 0.0;M3 CHK:0;cm4_sp_mode 0 [Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz] OPS=0x40 ring efuse init 2b 0b 40 00 01 12 28 00 00 08 31 37 59 54 52 50 [0.014423 Inits done] secure task start! high task start! low task start! boot bl31 NOTICE: BL31: v1.3(release):d9e1bbe85 NOTICE: BL31: Built : 19:07:25, Sep 7 2020 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2021.01-00035-g6180f7834d8f (Feb 09 2021 - 15:31:49 -0800) khadas-vim3l Model: Khadas VIM3L SoC: Amlogic Meson SM1 (Unknown) Revision 2b:b (40:2) DRAM: 2 GiB MMC: sd@ffe03000: 0, sd@ffe05000: 1, mmc@ffe07000: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@3000 Out: serial@3000 Err: serial@3000 Net: eth0: ethernet@ff3f0000 Verify GPT: success! switch to partitions #0, OK mmc2(part 0) is current device MMC read: dev # 2, block # 1024, count 4096 ... 4096 blocks read: OK There is no valid bmp file at the given address Hit any key to stop autoboot: 2  0 => setenv autoload no => setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff => dhcp Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.0.214 (8 ms) => setenv serverip 192.168.0.2 => tftp 0x1080000 3894973/tftp-deploy-r94mpkos/kernel/Image Speed: 100, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3894973/tftp-deploy-r94mpkos/kernel/Image'. Load address: 0x1080000 Loading: *################################################################# ######################################################T #T ########## ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###############################################T ################## ################################################################# ################################################################# ################################################################# ################################################################# ######################################## 1.2 MiB/s done Bytes transferred = 64508416 (3d85200 hex) => tftp 0x13000000 3894973/tftp-deploy-r94mpkos/ramdisk/ramdisk.cpio.gz.uboot Speed: 100, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3894973/tftp-deploy-r94mpkos/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x13000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 1.6 MiB/s done Bytes transferred = 34500674 (20e7042 hex) => setenv initrd_size ${filesize} => tftp 0x1000000 3894973/tftp-deploy-r94mpkos/dtb/meson-sm1-khadas-vim3l.dtb Speed: 100, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.214 Filename '3894973/tftp-deploy-r94mpkos/dtb/meson-sm1-khadas-vim3l.dtb'. Load address: 0x1000000 Loading: *###### 1.7 MiB/s done Bytes transferred = 77409 (12e61 hex) => setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x1080000 0x13000000 0x1000000 Moving Image from 0x1080000 to 0x1200000, end=5070000 ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 34500610 Bytes = 32.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x1000000 Loading Ramdisk to 73e24000, end 75f0b002 ... OK ERROR: reserving fdt memory region failed (addr=5000000 size=300000) Loading Device Tree to 0000000073e0e000, end 0000000073e23e60 ... OK vim3: successfully enabled PCIe Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050] [ 0.000000] Linux version 6.11.0-rc5-next-20240830 (KernelCI@build-j301688-arm64-gcc-12-defconfig-kselftest-sfh8n) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Aug 30 08:32:21 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Khadas VIM3L [ 0.000000] efi: UEFI not found. [ 0.000000] OF: reserved mem: Reserved memory: failed to reserve memory for node 'secmon@5000000': base 0x0000000005000000, size 3 MiB [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000063c00000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: 0x0000000063c00000..0x0000000073bfffff (262144 KiB) map reusable linux,cma [ 0.000000] OF: reserved mem: 0x0000000005000000..0x00000000052fffff (3072 KiB) nomap non-reusable secmon@5000000 [ 0.000000] OF: reserved mem: 0x0000000005300000..0x00000000072fffff (32768 KiB) nomap non-reusable secmon@5300000 [ 0.000000] earlycon: meson0 at MMIO 0x00000000ff803000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [meson0] enabled [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] NODE_DATA(0) allocated [mem 0x7fa07a40-0x7fa0a17f] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000052fffff] [ 0.000000] node 0: [mem 0x0000000005300000-0x00000000072fffff] [ 0.000000] node 0: [mem 0x0000000007300000-0x000000007fe5afff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] On node 0, zone DMA: 421 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 34 pages/cpu s100504 r8192 d30568 u139264 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 523867 <6>[ 0.000000] Policy zone: DMA <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:on <6>[ 0.000000] mem auto-init: clearing system memory may take some time... <6>[ 0.000000] stackdepot: allocating hash table via alloc_large_system_hash <6>[ 0.000000] stackdepot hash table entries: 131072 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 2MB <6>[ 0.000000] software IO TLB: area num 4. <6>[ 0.000000] software IO TLB: mapped [mem 0x000000007d100000-0x000000007d300000] (2MB) <4>[ 0.000000] ********************************************************** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** This system shows unhashed kernel memory addresses ** <4>[ 0.000000] ** via the console, logs, and other interfaces. This ** <4>[ 0.000000] ** might reduce the security of your system. ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** If you see this message and you are not debugging ** <4>[ 0.000000] ** the kernel, report this immediately to your system ** <4>[ 0.000000] ** administrator! ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ********************************************************** <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 73292 entries in 287 pages <6>[ 0.000000] ftrace: allocated 287 pages with 6 groups <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009140] Console: colour dummy device 80x25 <6>[ 0.013255] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) <6>[ 0.023643] pid_max: default: 32768 minimum: 301 <6>[ 0.028958] LSM: initializing lsm=capability,landlock,bpf,ima <6>[ 0.034849] landlock: Up and running. <6>[ 0.039297] LSM support for eBPF active <6>[ 0.043120] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.050332] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.074677] rcu: Hierarchical SRCU implementation. <6>[ 0.074724] rcu: Max phase no-delay instances is 1000. <6>[ 0.080370] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.098298] EFI services will not be available. <6>[ 0.100525] smp: Bringing up secondary CPUs ... <6>[ 0.104284] Detected VIPT I-cache on CPU1 <6>[ 0.104411] CPU1: Booted secondary processor 0x0000000100 [0x411fd050] <6>[ 0.110053] Detected VIPT I-cache on CPU2 <6>[ 0.110165] CPU2: Booted secondary processor 0x0000000200 [0x411fd050] <6>[ 0.114135] Detected VIPT I-cache on CPU3 <6>[ 0.114245] CPU3: Booted secondary processor 0x0000000300 [0x411fd050] <6>[ 0.114487] smp: Brought up 1 node, 4 CPUs <6>[ 0.146588] SMP: Total of 4 processors activated. <6>[ 0.151551] CPU: All CPU(s) started at EL2 <6>[ 0.155970] CPU features: detected: 32-bit EL0 Support <6>[ 0.161355] CPU features: detected: 32-bit EL1 Support <6>[ 0.166772] CPU features: detected: Data cache clean to the PoU not required for I/D coherence <6>[ 0.175694] CPU features: detected: Common not Private translations <6>[ 0.182255] CPU features: detected: CRC32 instructions <6>[ 0.187686] CPU features: detected: RCpc load-acquire (LDAPR) <6>[ 0.193718] CPU features: detected: LSE atomic instructions <6>[ 0.199580] CPU features: detected: Privileged Access Never <6>[ 0.205442] CPU features: detected: RAS Extension Support <6>[ 0.211206] alternatives: applying system-wide alternatives <6>[ 0.222390] Memory: 1647016K/2095468K available (23424K kernel code, 7764K rwdata, 14440K rodata, 17216K init, 858K bss, 179016K reserved, 262144K cma-reserved) <6>[ 0.233431] devtmpfs: initialized <6>[ 0.307312] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.311780] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.384680] 16784 pages in range for non-PLT usage <6>[ 0.384708] 508304 pages in range for PLT usage <6>[ 0.385480] pinctrl core: initialized pinctrl subsystem <6>[ 0.403527] DMI not present or invalid. <6>[ 0.408650] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.413188] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.417733] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.426198] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.433102] audit: initializing netlink subsys (disabled) <5>[ 0.439125] audit: type=2000 audit(0.348:1): state=initialized audit_enabled=0 res=1 <6>[ 0.445316] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.446579] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.453197] cpuidle: using governor menu <6>[ 0.465030] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.471194] ASID allocator initialised with 65536 entries <6>[ 0.488959] Serial: AMBA PL011 UART driver <6>[ 0.528480] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.613919] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.616934] platform ff900000.vpu: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0 <6>[ 0.674242] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /hdmi-connector <6>[ 0.677006] platform hdmi-connector: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0 <6>[ 0.694538] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.695976] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.702564] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.709637] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.716199] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.723285] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.729861] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.736936] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.752282] ACPI: Interpreter disabled. <6>[ 0.769421] iommu: Default domain type: Translated <6>[ 0.769468] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.784841] SCSI subsystem initialized <6>[ 0.786837] usbcore: registered new interface driver usbfs <6>[ 0.789185] usbcore: registered new interface driver hub <6>[ 0.794759] usbcore: registered new device driver usb <6>[ 0.805344] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.805381] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.814733] PTP clock support registered <6>[ 0.819557] EDAC MC: Ver: 3.0.0 <6>[ 0.824041] scmi_core: SCMI protocol bus registered <6>[ 0.832777] FPGA manager framework <6>[ 0.833465] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.840305] NET: Registered PF_ATMPVC protocol family <6>[ 0.842840] NET: Registered PF_ATMSVC protocol family <6>[ 0.849439] vgaarb: loaded <6>[ 0.852800] clocksource: Switched to clocksource arch_sys_counter <5>[ 1.532047] VFS: Disk quotas dquot_6.6.0 <6>[ 1.532175] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 1.540016] pnp: PnP ACPI: disabled <6>[ 1.569901] NET: Registered PF_INET protocol family <6>[ 1.570206] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.579949] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) <6>[ 1.586091] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.594107] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.602341] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear) <6>[ 1.610183] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 1.617313] MPTCP token hash table entries: 2048 (order: 3, 49152 bytes, linear) <6>[ 1.624517] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 1.631427] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 1.639439] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.646484] RPC: Registered named UNIX socket transport module. <6>[ 1.651000] RPC: Registered udp transport module. <6>[ 1.655959] RPC: Registered tcp transport module. <6>[ 1.660963] RPC: Registered tcp-with-tls transport module. <6>[ 1.666723] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.673474] NET: Registered PF_XDP protocol family <6>[ 1.678556] PCI: CLS 0 bytes, default 64 <6>[ 1.683464] Unpacking initramfs... <6>[ 1.703678] kvm [1]: nv: 552 coarse grained trap handlers <6>[ 1.704669] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.708471] kvm [1]: vgic interrupt IRQ9 <6>[ 1.712639] kvm [1]: VHE mode initialized successfully <5>[ 1.724382] Initialise system trusted keyrings <6>[ 1.725037] workingset: timestamp_bits=42 max_order=19 bucket_order=0 <6>[ 1.745009] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.746849] NFS: Registering the id_resolver key type <5>[ 1.750946] Key type id_resolver registered <5>[ 1.755311] Key type id_legacy registered <6>[ 1.759739] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.766605] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.774942] 9p: Installing v9fs 9p2000 file system support <6>[ 1.831805] NET: Registered PF_ALG protocol family <5>[ 1.831894] Key type asymmetric registered <5>[ 1.835636] Asymmetric key parser 'x509' registered <6>[ 1.841178] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) <6>[ 1.848517] io scheduler mq-deadline registered <6>[ 1.853315] io scheduler kyber registered <6>[ 1.857730] io scheduler bfq registered <4>[ 1.862641] test_firmware: interface ready <6>[ 1.878339] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized <6>[ 2.137213] soc soc0: Amlogic Meson SM1 (Unknown) Revision 2b:b (40:2) Detected <6>[ 2.195931] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.218274] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart <6>[ 2.228119] printk: legacy console [ttyAML0] enabled <6>[ 2.228119] printk: legacy console [ttyAML0] enabled <6>[ 2.232966] printk: legacy bootconsole [meson0] disabled <6>[ 2.232966] printk: legacy bootconsole [meson0] disabled <6>[ 2.260511] ffd24000.serial: ttyAML6 at MMIO 0xffd24000 (irq = 15, base_baud = 1500000) is a meson_uart <6>[ 2.265854] serial serial0: tty port ttyAML6 registered <6>[ 2.272219] msm_serial: driver initialized <6>[ 2.277091] SuperH (H)SCI(F) driver initialized <6>[ 2.280010] STM32 USART driver initialized <5>[ 2.293635] random: crng init done <6>[ 2.331103] loop: module loaded <6>[ 2.331690] lkdtm: No crash points registered, enable through debugfs <6>[ 2.343752] megasas: 07.727.03.00-rc1 <6>[ 2.390446] thunder_xcv, ver 1.0 <6>[ 2.390637] thunder_bgx, ver 1.0 <6>[ 2.391952] nicpf, ver 1.0 <6>[ 2.403936] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 2.405819] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 2.411592] hclge is initializing <6>[ 2.415096] e1000: Intel(R) PRO/1000 Network Driver <6>[ 2.420041] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 2.426219] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.431213] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.437575] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.442998] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.449072] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.455305] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.464044] sky2: driver version 1.30 <6>[ 2.474248] VFIO - User Level meta-driver version: 0.3 <6>[ 2.494370] usbcore: registered new interface driver usb-storage <6>[ 2.515712] i2c_dev: i2c /dev entries driver <6>[ 2.577009] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.577827] sdhci: Copyright(c) Pierre Ossman <6>[ 2.587561] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.595766] meson-gx-mmc ffe05000.mmc: Got CD GPIO <6>[ 2.595965] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.550142] Freeing initrd memory: 33692K <6>[ 3.557011] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.563991] meson-sm: secure-monitor enabled <6>[ 3.569347] hid: raw HID events driver (C) Jiri Kosina <6>[ 3.573049] usbcore: registered new interface driver usbhid <6>[ 3.574927] usbhid: USB HID core driver <6>[ 3.626448] IPv4 over IPsec tunneling driver <6>[ 3.628444] NET: Registered PF_INET6 protocol family <6>[ 3.633846] Segment Routing with IPv6 <6>[ 3.634649] In-situ OAM (IOAM) with IPv6 <6>[ 3.640560] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.648329] NET: Registered PF_PACKET protocol family <6>[ 3.650921] 9pnet: Installing 9P2000 support <5>[ 3.654807] Key type dns_resolver registered <6>[ 3.659659] NET: Registered PF_VSOCK protocol family <6>[ 3.664365] mpls_gso: MPLS GSO support <6>[ 3.745049] registered taskstats version 1 <5>[ 3.758327] Loading compiled-in X.509 certificates <5>[ 3.818989] Loaded X.509 cert 'Build time autogenerated kernel key: 4041b4d866812ba535b816c62e74659d932e877b' <6>[ 3.878542] Demotion targets for Node 0: null <6>[ 3.879399] ima: No TPM chip found, activating TPM-bypass! <6>[ 3.883336] ima: Allocated hash algorithm: sha1 <6>[ 3.888129] ima: No architecture policies found <6>[ 4.037428] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2 <6>[ 4.037480] dwc3-meson-g12a ffe09000.usb: USB3 ports: 0 <4>[ 4.052565] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator <4>[ 4.054930] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator <6>[ 4.062655] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM <6>[ 4.080121] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.080316] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.090673] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe64 hci version 0x110 quirks 0x0000808000000010 <6>[ 4.097953] xhci-hcd xhci-hcd.0.auto: irq 19, io mem 0xff500000 <6>[ 4.104726] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.109694] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.117580] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.126890] hub 1-0:1.0: USB hub found <6>[ 4.128383] hub 1-0:1.0: 2 ports detected <6>[ 4.134420] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.143120] hub 2-0:1.0: USB hub found <6>[ 4.144980] hub 2-0:1.0: 1 port detected <6>[ 4.152530] pca953x 0-0020: using no AI <6>[ 4.183081] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq <6>[ 4.370305] mmc1: new HS200 MMC card at address 0001 <6>[ 4.374101] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB <6>[ 4.387417] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 <6>[ 4.394509] mmcblk1boot0: mmc1:0001 AJTD4R 4.00 MiB <6>[ 4.404483] mmcblk1boot1: mmc1:0001 AJTD4R 4.00 MiB <6>[ 4.413062] mmcblk1rpmb: mmc1:0001 AJTD4R 4.00 MiB, chardev (509:0) <3>[ 7.153768] usb usb1-port1: connect-debounce failed <6>[ 16.545695] clk: Disabling unused clocks <6>[ 16.546466] PM: genpd: Disabling unused power domains <6>[ 16.549812] ALSA device list: <6>[ 16.552752] No soundcards found. <6>[ 16.602621] Freeing unused kernel memory: 17216K <6>[ 16.602876] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 16.786416] udevd[117]: starting version 3.2.9 <27>[ 16.797396] udevd[117]: specified user 'tss' unknown <27>[ 16.797623] udevd[117]: specified group 'tss' unknown <30>[ 16.806294] udevd[118]: starting eudev-3.2.9 <6>[ 17.568724] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0 <6>[ 17.596876] input: adc-keys as /devices/platform/adc-keys/input/input1 <6>[ 17.699850] meson-pcie fc000000.pcie: host bridge /soc/pcie@fc000000 ranges: <6>[ 17.705037] meson-pcie fc000000.pcie: IO 0x00fc600000..0x00fc6fffff -> 0x0000000000 <6>[ 17.718819] mc: Linux media interface: v0.10 <6>[ 17.727498] meson-pcie fc000000.pcie: MEM 0x00fc700000..0x00fdffffff -> 0x00fc700000 <6>[ 17.730299] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found <6>[ 17.730340] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found <6>[ 17.731012] meson8b-dwmac ff3f0000.ethernet: IRQ sfty not found <6>[ 17.744930] videodev: Linux video capture interface: v2.00 <6>[ 17.750498] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock <6>[ 17.766084] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37 <6>[ 17.769148] meson8b-dwmac ff3f0000.ethernet: DWMAC1000 <6>[ 17.775059] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported <6>[ 17.782601] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported <6>[ 17.783007] meson-pcie fc000000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 4G <6>[ 17.790442] meson8b-dwmac ff3f0000.ethernet: COE Type 2 <6>[ 17.803784] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported <6>[ 17.811156] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported <6>[ 17.818072] meson8b-dwmac ff3f0000.ethernet: Normal descriptors <6>[ 17.823962] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled <6>[ 17.830067] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer <4>[ 17.836244] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned. <3>[ 17.890926] meson-pcie fc000000.pcie: error: wait linkup timeout <6>[ 17.891240] meson-drm ff900000.vpu: Queued 1 outputs on vpu <3>[ 17.934526] meson-pcie fc000000.pcie: error: wait linkup timeout <6>[ 17.973916] meson-drm ff900000.vpu: CVBS Output connector not available <4>[ 17.974313] meson-pwm ff802000.pwm: using obsolete compatible, please consider updating dt <6>[ 18.019316] meson-vrtc ff8000a8.rtc: registered as rtc1 <6>[ 18.037427] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy) <3>[ 18.050003] debugfs: Directory 'ff800280.cec' with parent 'regmap' already present! <3>[ 18.118163] meson-pcie fc000000.pcie: error: wait linkup timeout <6>[ 18.175636] meson-gx-mmc ffe03000.mmc: allocated mmc-pwrseq <6>[ 18.220942] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver <4>[ 18.239485] rtc-hym8563 0-0051: no valid clock/calendar values available <6>[ 18.242501] rtc-hym8563 0-0051: registered as rtc0 <6>[ 18.243642] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops [meson_dw_hdmi]) <4>[ 18.260991] rtc-hym8563 0-0051: no valid clock/calendar values available <3>[ 18.262333] rtc-hym8563 0-0051: hctosys: unable to read the hardware clock <3>[ 18.269127] meson-drm ff900000.vpu: DSI transceiver device is disabled <6>[ 18.293934] [drm] Initialized meson 1.0.0 for ff900000.vpu on minor 0 <6>[ 18.316987] Registered IR keymap rc-khadas <3>[ 18.324511] meson-pcie fc000000.pcie: error: wait linkup timeout <6>[ 18.369348] panfrost ffe40000.gpu: clock rate = 24000000 <3>[ 18.369779] panfrost ffe40000.gpu: error -ENODEV: _opp_set_regulators: no regulator (mali) found <6>[ 18.380631] panfrost ffe40000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0 <6>[ 18.380655] panfrost ffe40000.gpu: features: 00000000,000027f7, issues: 00000000,00000400 <6>[ 18.380664] panfrost ffe40000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7 <6>[ 18.380673] panfrost ffe40000.gpu: shader_present=0x1 l2_present=0x1 <6>[ 18.388511] [drm] Initialized panfrost 1.2.0 for ffe40000.gpu on minor 1 <3>[ 18.388883] rc_core: Loaded IR protocol module ir-nec-decoder, but protocol nec still not available <6>[ 18.389189] rc rc0: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0 <6>[ 18.390657] rc rc0: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter <6>[ 18.391691] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0/input2 <6>[ 18.395485] rc rc0: sw decoder init <6>[ 18.395658] meson-ir ff808000.ir: receiver initialized <6>[ 18.401485] mmc2: new ultra high speed SDR50 SDIO card at address 0001 <6>[ 18.403096] Bluetooth: Core ver 2.22 <6>[ 18.403334] NET: Registered PF_BLUETOOTH protocol family <6>[ 18.403342] Bluetooth: HCI device and connection manager initialized <6>[ 18.403370] Bluetooth: HCI socket layer initialized <6>[ 18.403389] Bluetooth: L2CAP socket layer initialized <6>[ 18.403438] Bluetooth: SCO socket layer initialized <6>[ 18.429138] Bluetooth: HCI UART driver ver 2.3 <6>[ 18.429164] Bluetooth: HCI UART protocol H4 registered <6>[ 18.429411] Bluetooth: HCI UART protocol LL registered <4>[ 18.430835] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator <4>[ 18.431326] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator <6>[ 18.431752] Bluetooth: HCI UART protocol Broadcom registered <6>[ 18.431940] Bluetooth: HCI UART protocol QCA registered <6>[ 18.432115] Bluetooth: HCI UART protocol Marvell registered <6>[ 18.506613] Console: switching to colour frame buffer device 128x48 <3>[ 18.514565] meson-pcie fc000000.pcie: error: wait linkup timeout <3>[ 18.698781] meson-pcie fc000000.pcie: error: wait linkup timeout <6>[ 18.745293] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device <6>[ 18.786864] Bluetooth: hci0: BCM: chip id 121 <6>[ 18.787425] Bluetooth: hci0: BCM: features 0x0e <6>[ 18.792529] Bluetooth: hci0: BCM4359C0 <6>[ 18.794729] Bluetooth: hci0: BCM4359C0 (003.001.006) build 0000 <3>[ 18.801691] Bluetooth: hci0: BCM: firmware Patch file not found, tried: <3>[ 18.807691] Bluetooth: hci0: BCM: 'brcm/BCM4359C0.khadas,vim3l.hcd' <3>[ 18.814210] Bluetooth: hci0: BCM: 'brcm/BCM4359C0.hcd' <3>[ 18.819557] Bluetooth: hci0: BCM: 'brcm/BCM.khadas,vim3l.hcd' <5>[ 18.822327] cfg80211: Loading compiled-in X.509 certificates for regulatory database <3>[ 18.825563] Bluetooth: hci0: BCM: 'brcm/BCM.hcd' <1>[ 18.852907] Unable to handle kernel paging request at virtual address cccccccccccccccc <1>[ 18.855586] Mem abort info: <1>[ 18.858611] ESR = 0x0000000096000004 <3>[ 18.861821] meson-pcie fc000000.pcie: error: wait linkup timeout <1>[ 18.862859] EC = 0x25: DABT (current EL), IL = 32 bits <1>[ 18.874319] SET = 0, FnV = 0 <1>[ 18.877808] EA = 0, S1PTW = 0 <1>[ 18.880983] FSC = 0x04: level 0 translation fault <5>[ 18.881561] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <1>[ 18.886100] Data abort info: <1>[ 18.886106] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 <1>[ 18.886112] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 <1>[ 18.886117] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 <1>[ 18.886123] [cccccccccccccccc] address between user and kernel address ranges <0>[ 18.886131] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP <4>[ 18.886137] Modules linked in: snd_soc_hdmi_codec dw_hdmi_i2s_audio cfg80211(+) khadas_mcu_fan hci_uart btqca btbcm bluetooth ecdh_generic ecc rfkill panfrost pwrseq_core drm_shmem_helper crct10dif_ce khadas_mcu snd_soc_meson_axg_sound_card gpu_sched rtc_hym8563 snd_soc_meson_card_utils meson_gxbb_wdt rc_khadas meson_ir meson_gxl smsc snd_soc_meson_g12a_tohdmitx snd_soc_meson_codec_glue snd_soc_meson_axg_frddr snd_soc_meson_axg_tdmout snd_soc_meson_axg_tdmin axg_audio ao_cec_g12a reset_meson_audio_arb dwmac_generic meson_dw_hdmi sclk_div clk_phase pwm_meson snd_soc_meson_axg_toddr snd_soc_meson_axg_fifo dw_hdmi rtc_meson_vrtc meson_drm cec meson_vdec(C) meson_ddr_pmu_g12 drm_display_helper v4l2_mem2mem mdio_mux_meson_g12a meson_canvas videobuf2_dma_contig videobuf2_memops videobuf2_v4l2 drm_dma_helper videodev dwmac_meson8b videobuf2_common stmmac_platform mc stmmac pcs_xpcs pci_meson(+) display_connector drm_kms_helper drm nvmem_meson_efuse backlight adc_keys snd_soc_meson_axg_tdm_interface gpio_keys_polled <4>[ 18.886275] snd_soc_meson_axg_tdm_formatter <4>[ 18.886283] CPU: 0 UID: 0 PID: 11 Comm: kworker/u16:0 Tainted: G C 6.11.0-rc5-next-20240830 #1 <4>[ 18.886291] Tainted: [C]=CRAP <4>[ 18.886293] Hardware name: Khadas VIM3L (DT) <4>[ 18.886297] Workqueue: events_unbound deferred_probe_work_func <4>[ 18.886313] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) <4>[ 18.886318] pc : snd_soc_compensate_channel_connection_map+0xe8/0x1e8 <4>[ 18.886328] lr : snd_soc_bind_card+0x334/0xc68 <4>[ 18.886334] sp : ffff800083edb9d0 <4>[ 18.886336] x29: ffff800083edb9d0 x28: ffff800083c7b5f8 x27: ffff0000039938c0 <4>[ 18.886344] x26: 0000000000000028 x25: ffff000003f3da50 x24: 0000000000000002 <4>[ 18.886353] x23: ffff8000823fa610 x22: ffff000003f3d888 x21: ffff800083d50f70 <4>[ 18.886360] x20: ffff000011cf56c0 x19: 0000000000000000 x18: 0000000000000000 <4>[ 18.886367] x17: ffff7ffffd088000 x16: ffff800080000000 x15: ffff800080521080 <4>[ 18.886375] x14: 0000000000000001 x13: 0000000000000030 x12: 0101010101010101 <4>[ 18.886382] x11: ffff00007f8b3200 x10: 0000000000000000 x9 : ffff80008136727c <4>[ 18.886390] x8 : 0101010101010101 <5>[ 18.892807] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 18.895067] x7 : 7f7f7f7f7f7f7f7f x6 : 0000000000000001 <4>[ 18.901121] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <4>[ 18.906073] <4>[ 18.906076] x5 : cccccccccccccccc x4 : 0000000000000001 x3 : ffff000003991a80 <4>[ 18.906085] x2 : ffff000012838f38 x1 : cccccccccccccccc x0 : 0000000000000001 <4>[ 18.906094] Call trace: <4>[ 18.906097] snd_soc_compensate_channel_connection_map+0xe8/0x1e8 <4>[ 18.906106] snd_soc_bind_card+0x334/0xc68 <4>[ 18.906113] snd_soc_register_card+0xf8/0x118 <4>[ 18.906118] devm_snd_soc_register_card+0x54/0xb8 <4>[ 18.906127] meson_card_probe+0x254/0x2c0 [snd_soc_meson_card_utils] <6>[ 18.912087] cfg80211: failed to load regulatory.db <4>[ 18.918985] platform_probe+0x70/0x100 <4>[ 18.918994] really_probe+0xd4/0x3c0 <4>[ 18.919001] __driver_probe_device+0x90/0x1a0 <4>[ 18.919006] driver_probe_device+0x44/0x168 <4>[ 18.919011] __device_attach_driver+0xe0/0x1b8 <4>[ 18.919017] bus_for_each_drv+0x8c/0xf0 <4>[ 18.919022] __device_attach+0xa4/0x1e0 <4>[ 18.919027] device_initial_probe+0x1c/0x30 <4>[ 18.919033] bus_probe_device+0xb4/0xc0 <4>[ 18.919038] deferred_probe_work_func+0xc0/0x120 <4>[ 18.919043] process_one_work+0x184/0x408 <3>[ 19.014965] meson-pcie fc000000.pcie: error: wait linkup timeout <4>[ 19.019346] worker_thread+0x250/0x360 <4>[ 19.019354] kthread+0x108/0x120 <4>[ 19.019361] ret_from_fork+0x10/0x20 <3>[ 19.174880] meson-pcie fc000000.pcie: error: wait linkup timeout <0>[ 19.176823] Code: 540004aa f9401a80 9b250265 b4000445 (294014a3) <4>[ 19.176828] ---[ end trace 0000000000000000 ]--- <6>[ 19.318811] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4359-sdio for chip BCM4359/9 <4>[ 19.322293] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4359-sdio.khadas,vim3l.bin failed with error -2 <4>[ 19.336515] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4359-sdio.bin failed with error -2 <3>[ 19.418131] meson-pcie fc000000.pcie: error: wait linkup timeout <3>[ 19.558977] meson-pcie fc000000.pcie: error: wait linkup timeout <6>[ 19.656816] meson-pcie fc000000.pcie: Phy link never came up <6>[ 19.658060] meson-pcie fc000000.pcie: PCI host bridge to bus 0000:00 <6>[ 19.663809] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 19.669437] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] <6>[ 19.675953] pci_bus 0000:00: root bus resource [mem 0xfc700000-0xfdffffff] <6>[ 19.683119] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 PCIe Root Port <6>[ 19.690655] pci 0000:00:00.0: ROM [mem 0x00000000-0x0000ffff pref] <6>[ 19.697005] pci 0000:00:00.0: PCI bridge to [bus 01-ff] <6>[ 19.702521] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] <6>[ 19.708774] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] <6>[ 19.715818] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] <6>[ 19.724159] pci 0000:00:00.0: supports D1 <6>[ 19.727511] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold <3>[ 19.778960] meson-pcie fc000000.pcie: error: wait linkup timeout <6>[ 19.780864] pci 0000:00:00.0: ROM [mem 0xfc700000-0xfc70ffff pref]: assigned <6>[ 19.786916] pci 0000:00:00.0: PCI bridge to [bus 01-ff] <6>[ 19.792394] pci_bus 0000:00: resource 4 [io 0x0000-0xfffff] <6>[ 19.798244] pci_bus 0000:00: resource 5 [mem 0xfc700000-0xfdffffff] <6>[ 19.805935] pcieport 0000:00:00.0: PME: Signaling with IRQ 44 <6>[ 19.811535] pcieport 0000:00:00.0: AER: enabled with IRQ 44 <3>[ 20.349137] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3894973/environment / # /lava-3894973/bin/lava-test-runner /lava-3894973/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3894973/0/tests/0_dmesg + cat uuid + UUID=3894973_1.5.2.4.1 + set +x <8>[ 28.212659] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 28.259158] kern :alert : Unable to handle kernel paging request at virtual address cccccccccccccccc kern :alert : Mem abort info: kern :alert : ESR = 0x0000000096000004 kern :alert : EC = 0x25: DABT (current EL), IL = 32 bits <8>[ 28.302806] kern :alert : SET = 0, FnV = 0 kern :alert : EA = 0, S1PTW = 0 kern :alert : FSC = 0x04: level 0 translation fault kern :alert : Data abort info: kern :alert : ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 kern :alert : CM = 0, WnR = 0, TnD = 0, TagAccess = 0 kern :alert : GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 kern :alert : [cccccccccccccccc] address between user and kernel address ranges kern :emerg : Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP kern :emerg :<8>[ 28.356546] Code: 540004aa f9401a80 9b250<8>[ 28.366571] 265 b4000445 (294014a3) + set +x / #