connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='default', state=, avail=True, host='nuc-1', port=37133, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:37133 connected to 192.168.0.1 (port 37133) Escape character: Ctrl-\ Type the escape character to get to the prompt. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no U-Boot> setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff U-Boot> dhcp gmac0: PHY present at 0 gmac0: Starting autonegotiation... gmac0: Autonegotiation complete gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) BOOTP broadcast 1 DHCP client bound to address 192.168.0.135 U-Boot> setenv serverip 192.168.0.2 U-Boot> tftp 0x22100000 3900348/tftp-deploy-4p236gtf/kernel/zImage gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3900348/tftp-deploy-4p236gtf/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################### 2.8 MiB/s done Bytes transferred = 10809856 (a4f200 hex) U-Boot> tftp 0x23000000 3900348/tftp-deploy-4p236gtf/ramdisk/ramdisk.cpio.gz.uboot gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3900348/tftp-deploy-4p236gtf/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 2.8 MiB/s done Bytes transferred = 17516977 (10b49b1 hex) U-Boot> setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 3900348/tftp-deploy-4p236gtf/dtb/at91-sama5d4_xplained.dtb gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3900348/tftp-deploy-4p236gtf/dtb/at91-sama5d4_xplained.dtb'. Load address: 0x22000000 Loading: *### 3.1 MiB/s done Bytes transferred = 36139 (8d2b hex) U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0xa4f200 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17516913 Bytes = 16.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 2200bd2a Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc1-next-20241003 (KernelCI@build-j330707-arm-gcc-12-multi-v7-defconfig-config-thumb2-4hgv7) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Thu Oct 3 04:49:45 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Atmel SAMA5D4 Xplained [ 0.000000] earlycon: atmel_serial0 at MMIO 0xfc00c000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu s40908 r8192 d20532 u69632 [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x06020000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: timer@fc024000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 173750949719 ns <6>[ 0.000004] sched_clock: 32 bits at 11MHz, resolution 90ns, wraps every 195225786322ns <6>[ 0.008146] Switching to timer-based delay loop, resolution 90ns <6>[ 0.015276] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 10859434279 ns <6>[ 0.028401] Console: colour dummy device 80x30 <6>[ 0.033154] Calibrating delay loop (skipped), value calculated using timer frequency.. 22.00 BogoMIPS (lpj=110000) <6>[ 0.043740] CPU: Testing write buffer coherency: ok <6>[ 0.048854] pid_max: default: 32768 minimum: 301 <6>[ 0.054079] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.061619] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.071602] CPU0: thread -1, cpu 0, socket -1, mpidr c0000000 <6>[ 0.080698] Setting up static identity map for 0x20300000 - 0x203000a0 <6>[ 0.090084] rcu: Hierarchical SRCU implementation. <6>[ 0.095037] rcu: Max phase no-delay instances is 1000. <6>[ 0.106288] EFI services will not be available. <6>[ 0.111616] smp: Bringing up secondary CPUs ... <6>[ 0.116338] smp: Brought up 1 node, 1 CPU <6>[ 0.120714] SMP: Total of 1 processors activated (22.00 BogoMIPS). <6>[ 0.127056] CPU: All CPU(s) started in SVC mode. <6>[ 0.132236] Memory: 410720K/524288K available (11264K kernel code, 2547K rwdata, 6792K rodata, 2048K init, 430K bss, 46444K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.148479] devtmpfs: initialized <6>[ 0.165582] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 <6>[ 0.174055] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.184181] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.198951] pinctrl core: initialized pinctrl subsystem <6>[ 0.209902] DMI not present or invalid. <6>[ 0.216895] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.227805] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.240530] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.240741] cpuidle: using governor menu <6>[ 0.300281] AT91: PM: standby: standby, suspend: standby <6>[ 0.305785] No ATAGs? <6>[ 0.308490] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.316770] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.324694] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.334661] gpio-at91 fc06a000.gpio: at address (ptrval) <4>[ 0.340966] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.351021] gpio-at91 fc06b000.gpio: at address (ptrval) <4>[ 0.357139] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.367276] gpio-at91 fc06c000.gpio: at address (ptrval) <4>[ 0.373569] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.383782] gpio-at91 fc068000.gpio: at address (ptrval) <4>[ 0.389943] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.400403] gpio-at91 fc06d000.gpio: at address (ptrval) <6>[ 0.408027] pinctrl-at91 ahb:apb:pinctrl@fc06a000: initialized AT91 pinctrl driver <6>[ 0.429373] Serial: AMBA PL011 UART driver <6>[ 0.476199] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.486768] at_xdmac f0014000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.523589] AT91: Detected SoC family: sama5d4 <6>[ 0.528198] AT91: Detected SoC: sama5d44, revision 0 <6>[ 0.538765] iommu: Default domain type: Translated <6>[ 0.543798] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.582597] SCSI subsystem initialized <6>[ 0.601315] usbcore: registered new interface driver usbfs <6>[ 0.607037] usbcore: registered new interface driver hub <6>[ 0.612719] usbcore: registered new device driver usb <6>[ 0.621196] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.626318] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.635850] PTP clock support registered <6>[ 0.640353] EDAC MC: Ver: 3.0.0 <6>[ 0.689263] scmi_core: SCMI protocol bus registered <6>[ 0.710907] vgaarb: loaded <6>[ 0.714844] clocksource: Switched to clocksource timer@fc024000 <6>[ 0.793600] NET: Registered PF_INET protocol family <6>[ 0.799309] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.809542] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.818212] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.826191] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.834231] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 0.841986] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.848778] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.855599] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.863114] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.953538] RPC: Registered named UNIX socket transport module. <6>[ 0.959729] RPC: Registered udp transport module. <6>[ 0.964611] RPC: Registered tcp transport module. <6>[ 0.969628] RPC: Registered tcp-with-tls transport module. <6>[ 0.975430] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.982085] PCI: CLS 0 bytes, default 64 <5>[ 0.988995] Initialise system trusted keyrings <6>[ 1.015844] Trying to unpack rootfs image as initramfs... <6>[ 1.066615] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 1.074086] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.116481] NFS: Registering the id_resolver key type <5>[ 1.121805] Key type id_resolver registered <5>[ 1.126305] Key type id_legacy registered <6>[ 1.130534] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.137570] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 1.196417] Key type asymmetric registered <5>[ 1.200683] Asymmetric key parser 'x509' registered <6>[ 1.206214] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.213783] io scheduler mq-deadline registered <6>[ 1.218666] io scheduler kyber registered <6>[ 1.222943] io scheduler bfq registered <6>[ 6.423871] Freeing initrd memory: 17108K <6>[ 6.456669] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 6.739975] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.759829] msm_serial: driver initialized <6>[ 6.765103] SuperH (H)SCI(F) driver initialized <6>[ 6.770477] STMicroelectronics ASC driver initialized <6>[ 6.776089] STM32 USART driver initialized <5>[ 6.785308] random: crng init done <6>[ 6.829628] brd: module loaded <6>[ 6.847045] loop: module loaded <6>[ 6.855634] atmel_usart_serial.0.auto: ttyAT5 at MMIO 0xf8004000 (irq = 25, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 6.870137] atmel_usart_serial.1.auto: ttyAT0 at MMIO 0xfc00c000 (irq = 26, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 6.880893] printk: legacy console [ttyAT0] enabled <6>[ 6.880893] printk: legacy console [ttyAT0] enabled <6>[ 6.891088] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 6.891088] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 6.907651] atmel_usart_serial.2.auto: ttyAT1 at MMIO 0xfc010000 (irq = 27, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 6.950432] CAN device driver interface <6>[ 7.040718] macb f8020000.ethernet eth0: Cadence GEM rev 0x00020120 at 0xf8020000 irq 28 (52:11:6d:6b:d5:8f) <6>[ 7.052601] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.061490] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.066779] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.073035] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.078732] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.095812] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 7.101725] usbcore: registered new interface driver pegasus <6>[ 7.107782] usbcore: registered new interface driver asix <6>[ 7.113488] usbcore: registered new interface driver ax88179_178a <6>[ 7.119948] usbcore: registered new interface driver cdc_ether <6>[ 7.126155] usbcore: registered new interface driver smsc75xx <6>[ 7.132210] usbcore: registered new interface driver smsc95xx <6>[ 7.138350] usbcore: registered new interface driver net1080 <6>[ 7.144354] usbcore: registered new interface driver cdc_subset <6>[ 7.150664] usbcore: registered new interface driver zaurus <6>[ 7.156603] usbcore: registered new interface driver cdc_ncm <6>[ 7.174560] atmel-ehci 600000.ehci: EHCI Host Controller <6>[ 7.180352] atmel-ehci 600000.ehci: new USB bus registered, assigned bus number 1 <6>[ 7.192476] atmel-ehci 600000.ehci: irq 30, io mem 0x00600000 <6>[ 7.214933] atmel-ehci 600000.ehci: USB 2.0 started, EHCI 1.00 <6>[ 7.223157] hub 1-0:1.0: USB hub found <6>[ 7.227462] hub 1-0:1.0: 3 ports detected <6>[ 7.236864] at91_ohci 500000.ohci: USB Host Controller <6>[ 7.242327] at91_ohci 500000.ohci: new USB bus registered, assigned bus number 2 <6>[ 7.250668] at91_ohci 500000.ohci: irq 30, io mem 0x00500000 <6>[ 7.320983] hub 2-0:1.0: USB hub found <6>[ 7.325277] hub 2-0:1.0: 3 ports detected <6>[ 7.333301] usbcore: registered new interface driver usb-storage <6>[ 7.353979] i2c_dev: i2c /dev entries driver <6>[ 7.370786] at91-reset fc068600.reset-controller: Starting after RTC wakeup <6>[ 7.392955] sama5d4_wdt fc068640.watchdog: initialized (timeout = 16 sec, nowayout = 0) <6>[ 7.416886] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.423328] sdhci: Copyright(c) Pierre Ossman <6>[ 7.432935] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.443560] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.460756] slot@0 enforce active low on GPIO handle <6>[ 7.466432] atmel_mci fc000000.mmc: version: 0x600 <6>[ 7.472736] usbcore: registered new interface driver usbhid <6>[ 7.478743] usbhid: USB HID core driver <6>[ 7.493814] atmel_mci fc000000.mmc: using dma0chan0 for DMA transfers <6>[ 7.504394] atmel-nand-controller 10000000.ebi:nand-controller: using dma0chan1 for DMA transfers <6>[ 7.522740] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc <6>[ 7.529566] nand: Micron MT29F4G08ABAEAWP <6>[ 7.533814] nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 <6>[ 7.543579] Bad block table found at page 131008, version 0x01 <6>[ 7.551242] Bad block table found at page 130944, version 0x01 <6>[ 7.557979] atmel_mci fc000000.mmc: Atmel MCI controller at 0xfc000000 irq 31, 1 slots <5>[ 7.567373] 7 fixed-partitions partitions found on MTD device atmel_nand <5>[ 7.574415] Creating 7 MTD partitions on "atmel_nand": <5>[ 7.579907] 0x000000000000-0x000000040000 : "at91bootstrap" <5>[ 7.589146] 0x000000040000-0x000000100000 : "bootloader" <5>[ 7.598079] 0x000000100000-0x000000140000 : "bootloader env redundant" <5>[ 7.608159] 0x000000140000-0x000000180000 : "bootloader env" <5>[ 7.617435] 0x000000180000-0x000000200000 : "device tree" <5>[ 7.626374] 0x000000200000-0x000000800000 : "kernel" <5>[ 7.634768] 0x000000800000-0x000020000000 : "rootfs" <6>[ 7.658267] NET: Registered PF_INET6 protocol family <6>[ 7.666448] Segment Routing with IPv6 <6>[ 7.670458] In-situ OAM (IOAM) with IPv6 <6>[ 7.674906] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.682437] NET: Registered PF_PACKET protocol family <6>[ 7.687871] can: controller area network core <6>[ 7.692607] NET: Registered PF_CAN protocol family <6>[ 7.697753] can: raw protocol <6>[ 7.700953] can: broadcast manager protocol <6>[ 7.705464] can: netlink gateway - max_hops=1 <5>[ 7.710896] Key type dns_resolver registered <6>[ 7.715955] ThumbEE CPU extension supported. <5>[ 7.720486] Registering SWP/SWPB emulation handler <5>[ 7.749245] Loading compiled-in X.509 certificates <6>[ 7.788462] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 7.867800] macb f8020000.ethernet eth0: PHY [f8020000.ethernet-ffffffff:01] driver [Micrel KSZ8081 or KSZ8091] (irq=29) <6>[ 7.879933] macb f8020000.ethernet eth0: configuring for phy/rmii link mode <6>[ 9.510729] macb f8020000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 9.544894] Sending DHCP requests ., OK <6>[ 9.589067] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.135 <6>[ 9.597165] IP-Config: Complete: <6>[ 9.600613] device=eth0, hwaddr=52:11:6d:6b:d5:8f, ipaddr=192.168.0.135, mask=255.255.255.0, gw=192.168.0.254 <6>[ 9.611307] host=192.168.0.135, domain=shed, nis-domain=(none) <6>[ 9.617866] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 9.617892] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 9.632084] clk: Disabling unused clocks <6>[ 9.636543] PM: genpd: Disabling unused power domains <6>[ 9.643442] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan2 for rx DMA transfers <6>[ 9.652997] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan3 for tx DMA transfers <6>[ 9.668042] Freeing unused kernel image (initmem) memory: 2048K <6>[ 9.674622] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.068387] udevd[74]: starting version 3.2.9 <27>[ 10.098379] udevd[74]: specified user 'tss' unknown <27>[ 10.103977] udevd[74]: specified group 'tss' unknown <30>[ 10.126421] udevd[75]: starting eudev-3.2.9 <4>[ 13.285318] mtdblock: MTD device 'at91bootstrap' is NAND, please consider using UBI block devices instead. <4>[ 13.330299] mtdblock: MTD device 'bootloader' is NAND, please consider using UBI block devices instead. <6>[ 13.365317] at91_i2c f8014000.i2c: using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers <4>[ 13.407229] mtdblock: MTD device 'bootloader env redundant' is NAND, please consider using UBI block devices instead. <4>[ 13.420700] mtdblock: MTD device 'bootloader env' is NAND, please consider using UBI block devices instead. <6>[ 13.451752] i2c i2c-0: using pinctrl states for GPIO recovery <6>[ 13.458082] i2c i2c-0: using generic GPIOs for recovery <6>[ 13.463672] at91_i2c f8014000.i2c: AT91 i2c bus driver (hw version: 0x502). <4>[ 13.531820] mtdblock: MTD device 'device tree' is NAND, please consider using UBI block devices instead. <4>[ 13.560158] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. <4>[ 13.586833] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. <6>[ 14.046076] atmel_spi fc018000.spi: Using dma0chan6 (tx) and dma0chan7 (rx) for DMA transfers <6>[ 14.091521] iio iio:device0: Resolution used: 10 bits <6>[ 14.097068] iio iio:device0: ADC Touch screen is disabled. <6>[ 14.205006] atmel_spi fc018000.spi: Atmel SPI Controller version 0x221 at 0xfc018000 (irq 36) <6>[ 14.242459] atmel_aes fc044000.crypto: version: 0x201 <6>[ 14.321288] atmel_tdes fc04c000.crypto: version: 0x702 <6>[ 14.329299] atmel_sha fc050000.crypto: version: 0x420 <6>[ 14.348347] atmel_aes fc044000.crypto: Atmel AES - Using dma1chan0, dma1chan1 for DMA transfers <6>[ 14.425239] atmel_sha fc050000.crypto: using dma1chan2 for DMA transfers <6>[ 14.432243] atmel_sha fc050000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 14.441446] atmel_tdes fc04c000.crypto: using dma1chan3, dma1chan4 for DMA transfers <6>[ 14.449635] atmel_tdes fc04c000.crypto: Atmel DES/TDES <6>[ 14.710263] at91_rtc fc0686b0.rtc: registered as rtc0 <6>[ 14.715793] at91_rtc fc0686b0.rtc: setting system clock to 2012-01-01T00:00:30 UTC (1325376030) <6>[ 14.724850] at91_rtc fc0686b0.rtc: AT91 Real Time Clock driver. done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3900348/environment / # /lava-3900348/bin/lava-test-runner /lava-3900348/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3900348/0/tests/0_dmesg + cat uuid + UUID=3900348_<.8.>[ 17.854679] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.967341] <8>[ 18.068066] <8>[ 18.169232] + set +x <8>[ 18.181630] / #