connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='default', state=, avail=True, host='nuc-1', port=37133, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:37133 connected to 192.168.0.1 (port 37133) Escape character: Ctrl-\ Type the escape character to get to the prompt. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no U-Boot> setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff U-Boot> dhcp gmac0: PHY present at 0 gmac0: Starting autonegotiation... gmac0: Autonegotiation complete gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) BOOTP broadcast 1 DHCP client bound to address 192.168.0.135 U-Boot> setenv serverip 192.168.0.2 U-Boot> tftp 0x22100000 3900408/tftp-deploy-qeu9m6iy/kernel/zImage gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3900408/tftp-deploy-qeu9m6iy/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# # 3.1 MiB/s done Bytes transferred = 11461120 (aee200 hex) U-Boot> tftp 0x23000000 3900408/tftp-deploy-qeu9m6iy/ramdisk/ramdisk.cpio.gz.uboot gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3900408/tftp-deploy-qeu9m6iy/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 3.2 MiB/s done Bytes transferred = 17981210 (1125f1a hex) U-Boot> setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 3900408/tftp-deploy-qeu9m6iy/dtb/at91-sama5d4_xplained.dtb gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3900408/tftp-deploy-qeu9m6iy/dtb/at91-sama5d4_xplained.dtb'. Load address: 0x22000000 Loading: *### 1.9 MiB/s done Bytes transferred = 36139 (8d2b hex) U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0xaee200 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17981146 Bytes = 17.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 2200bd2a Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc1-next-20241003 (KernelCI@build-j330823-arm-gcc-12-multi-v7-defconfig-tf65k) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Thu Oct 3 05:21:42 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Atmel SAMA5D4 Xplained [ 0.000000] earlycon: atmel_serial0 at MMIO 0xfc00c000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000003fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu s40908 r8192 d20532 u69632 [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x06020000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] clocksource: timer@fc024000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 173750949719 ns <6>[ 0.000005] sched_clock: 32 bits at 11MHz, resolution 90ns, wraps every 195225786322ns <6>[ 0.008139] Switching to timer-based delay loop, resolution 90ns <6>[ 0.015273] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 10859434279 ns <6>[ 0.028351] Console: colour dummy device 80x30 <6>[ 0.033134] Calibrating delay loop (skipped), value calculated using timer frequency.. 22.00 BogoMIPS (lpj=110000) <6>[ 0.043744] CPU: Testing write buffer coherency: ok <6>[ 0.048876] pid_max: default: 32768 minimum: 301 <6>[ 0.054176] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.061745] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.072061] CPU0: thread -1, cpu 0, socket -1, mpidr c0000000 <6>[ 0.082024] Setting up static identity map for 0x20300000 - 0x203000ac <6>[ 0.091597] rcu: Hierarchical SRCU implementation. <6>[ 0.096566] rcu: Max phase no-delay instances is 1000. <6>[ 0.108094] EFI services will not be available. <6>[ 0.113572] smp: Bringing up secondary CPUs ... <6>[ 0.118311] smp: Brought up 1 node, 1 CPU <6>[ 0.122731] SMP: Total of 1 processors activated (22.00 BogoMIPS). <6>[ 0.129075] CPU: All CPU(s) started in SVC mode. <6>[ 0.134284] Memory: 405148K/524288K available (16384K kernel code, 2547K rwdata, 6792K rodata, 2048K init, 430K bss, 52016K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.150917] devtmpfs: initialized <6>[ 0.169577] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 <6>[ 0.178132] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.188265] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.202444] pinctrl core: initialized pinctrl subsystem <6>[ 0.213833] DMI not present or invalid. <6>[ 0.221179] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.232198] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.245249] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.245512] cpuidle: using governor menu <6>[ 0.307526] AT91: PM: standby: standby, suspend: standby <6>[ 0.313145] No ATAGs? <6>[ 0.315769] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.324073] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.332140] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.342293] gpio-at91 fc06a000.gpio: at address (ptrval) <4>[ 0.348568] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.358880] gpio-at91 fc06b000.gpio: at address (ptrval) <4>[ 0.365287] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.375574] gpio-at91 fc06c000.gpio: at address (ptrval) <4>[ 0.382049] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.392467] gpio-at91 fc068000.gpio: at address (ptrval) <4>[ 0.398769] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.409339] gpio-at91 fc06d000.gpio: at address (ptrval) <6>[ 0.417254] pinctrl-at91 ahb:apb:pinctrl@fc06a000: initialized AT91 pinctrl driver <6>[ 0.439348] Serial: AMBA PL011 UART driver <6>[ 0.485585] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.496730] at_xdmac f0014000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.543655] AT91: Detected SoC family: sama5d4 <6>[ 0.548272] AT91: Detected SoC: sama5d44, revision 0 <6>[ 0.558993] iommu: Default domain type: Translated <6>[ 0.564072] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.602182] SCSI subsystem initialized <6>[ 0.612465] usbcore: registered new interface driver usbfs <6>[ 0.618204] usbcore: registered new interface driver hub <6>[ 0.623933] usbcore: registered new device driver usb <6>[ 0.632557] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.637692] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.647254] PTP clock support registered <6>[ 0.651757] EDAC MC: Ver: 3.0.0 <6>[ 0.699202] scmi_core: SCMI protocol bus registered <6>[ 0.724598] vgaarb: loaded <6>[ 0.728733] clocksource: Switched to clocksource timer@fc024000 <6>[ 0.810774] NET: Registered PF_INET protocol family <6>[ 0.816431] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.826879] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.835582] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.843583] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.851663] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 0.859368] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.866126] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.873005] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.880648] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.967749] RPC: Registered named UNIX socket transport module. <6>[ 0.973974] RPC: Registered udp transport module. <6>[ 0.978891] RPC: Registered tcp transport module. <6>[ 0.983813] RPC: Registered tcp-with-tls transport module. <6>[ 0.989674] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.996313] PCI: CLS 0 bytes, default 64 <5>[ 1.003535] Initialise system trusted keyrings <6>[ 1.030050] Trying to unpack rootfs image as initramfs... <6>[ 1.079544] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 1.087158] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.131208] NFS: Registering the id_resolver key type <5>[ 1.136570] Key type id_resolver registered <5>[ 1.141115] Key type id_legacy registered <6>[ 1.145384] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.152374] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 1.240912] Key type asymmetric registered <5>[ 1.245194] Asymmetric key parser 'x509' registered <6>[ 1.250779] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.258355] io scheduler mq-deadline registered <6>[ 1.263282] io scheduler kyber registered <6>[ 1.267535] io scheduler bfq registered <6>[ 6.570237] Freeing initrd memory: 17560K <6>[ 6.600809] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 6.932395] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.953983] msm_serial: driver initialized <6>[ 6.959372] SuperH (H)SCI(F) driver initialized <6>[ 6.964742] STMicroelectronics ASC driver initialized <6>[ 6.970404] STM32 USART driver initialized <5>[ 6.980270] random: crng init done <6>[ 7.029239] brd: module loaded <6>[ 7.048297] loop: module loaded <6>[ 7.057337] atmel_usart_serial.0.auto: ttyAT5 at MMIO 0xf8004000 (irq = 25, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 7.072563] atmel_usart_serial.1.auto: ttyAT0 at MMIO 0xfc00c000 (irq = 26, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 7.083383] printk: legacy console [ttyAT0] enabled <6>[ 7.083383] printk: legacy console [ttyAT0] enabled <6>[ 7.093676] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 7.093676] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 7.110855] atmel_usart_serial.2.auto: ttyAT1 at MMIO 0xfc010000 (irq = 27, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 7.156290] CAN device driver interface <6>[ 7.249160] macb f8020000.ethernet eth0: Cadence GEM rev 0x00020120 at 0xf8020000 irq 28 (52:11:6d:6b:d5:8f) <6>[ 7.261093] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.270161] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.275376] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.281779] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.287418] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.305015] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 7.311100] usbcore: registered new interface driver pegasus <6>[ 7.317088] usbcore: registered new interface driver asix <6>[ 7.322889] usbcore: registered new interface driver ax88179_178a <6>[ 7.329368] usbcore: registered new interface driver cdc_ether <6>[ 7.335544] usbcore: registered new interface driver smsc75xx <6>[ 7.341682] usbcore: registered new interface driver smsc95xx <6>[ 7.347750] usbcore: registered new interface driver net1080 <6>[ 7.353867] usbcore: registered new interface driver cdc_subset <6>[ 7.360195] usbcore: registered new interface driver zaurus <6>[ 7.366091] usbcore: registered new interface driver cdc_ncm <6>[ 7.384555] atmel-ehci 600000.ehci: EHCI Host Controller <6>[ 7.390379] atmel-ehci 600000.ehci: new USB bus registered, assigned bus number 1 <6>[ 7.402501] atmel-ehci 600000.ehci: irq 30, io mem 0x00600000 <6>[ 7.418942] atmel-ehci 600000.ehci: USB 2.0 started, EHCI 1.00 <6>[ 7.427597] hub 1-0:1.0: USB hub found <6>[ 7.431985] hub 1-0:1.0: 3 ports detected <6>[ 7.441983] at91_ohci 500000.ohci: USB Host Controller <6>[ 7.447461] at91_ohci 500000.ohci: new USB bus registered, assigned bus number 2 <6>[ 7.455923] at91_ohci 500000.ohci: irq 30, io mem 0x00500000 <6>[ 7.525291] hub 2-0:1.0: USB hub found <6>[ 7.529675] hub 2-0:1.0: 3 ports detected <6>[ 7.538111] usbcore: registered new interface driver usb-storage <6>[ 7.560126] i2c_dev: i2c /dev entries driver <6>[ 7.577355] at91-reset fc068600.reset-controller: Starting after RTC wakeup <6>[ 7.600497] sama5d4_wdt fc068640.watchdog: initialized (timeout = 16 sec, nowayout = 0) <6>[ 7.625301] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.631918] sdhci: Copyright(c) Pierre Ossman <6>[ 7.641700] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.652537] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.670290] slot@0 enforce active low on GPIO handle <6>[ 7.675834] atmel_mci fc000000.mmc: version: 0x600 <6>[ 7.682481] usbcore: registered new interface driver usbhid <6>[ 7.688325] usbhid: USB HID core driver <6>[ 7.704129] atmel_mci fc000000.mmc: using dma0chan0 for DMA transfers <6>[ 7.715063] atmel-nand-controller 10000000.ebi:nand-controller: using dma0chan1 for DMA transfers <6>[ 7.733578] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc <6>[ 7.740378] nand: Micron MT29F4G08ABAEAWP <6>[ 7.744623] nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 <6>[ 7.754642] Bad block table found at page 131008, version 0x01 <6>[ 7.762509] Bad block table found at page 130944, version 0x01 <6>[ 7.769371] atmel_mci fc000000.mmc: Atmel MCI controller at 0xfc000000 irq 31, 1 slots <5>[ 7.778977] 7 fixed-partitions partitions found on MTD device atmel_nand <5>[ 7.786039] Creating 7 MTD partitions on "atmel_nand": <5>[ 7.791531] 0x000000000000-0x000000040000 : "at91bootstrap" <5>[ 7.801344] 0x000000040000-0x000000100000 : "bootloader" <5>[ 7.810701] 0x000000100000-0x000000140000 : "bootloader env redundant" <5>[ 7.821211] 0x000000140000-0x000000180000 : "bootloader env" <5>[ 7.830931] 0x000000180000-0x000000200000 : "device tree" <5>[ 7.840423] 0x000000200000-0x000000800000 : "kernel" <5>[ 7.849453] 0x000000800000-0x000020000000 : "rootfs" <6>[ 7.873910] NET: Registered PF_INET6 protocol family <6>[ 7.882398] Segment Routing with IPv6 <6>[ 7.886444] In-situ OAM (IOAM) with IPv6 <6>[ 7.890961] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.898801] NET: Registered PF_PACKET protocol family <6>[ 7.904130] can: controller area network core <6>[ 7.908984] NET: Registered PF_CAN protocol family <6>[ 7.914025] can: raw protocol <6>[ 7.917260] can: broadcast manager protocol <6>[ 7.921800] can: netlink gateway - max_hops=1 <5>[ 7.927267] Key type dns_resolver registered <6>[ 7.932399] ThumbEE CPU extension supported. <5>[ 7.936942] Registering SWP/SWPB emulation handler <5>[ 7.968234] Loading compiled-in X.509 certificates <6>[ 8.008385] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 8.081889] macb f8020000.ethernet eth0: PHY [f8020000.ethernet-ffffffff:01] driver [Micrel KSZ8081 or KSZ8091] (irq=29) <6>[ 8.094225] macb f8020000.ethernet eth0: configuring for phy/rmii link mode <6>[ 9.761013] macb f8020000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 9.788826] Sending DHCP requests ., OK <6>[ 9.833024] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.135 <6>[ 9.841147] IP-Config: Complete: <6>[ 9.844596] device=eth0, hwaddr=52:11:6d:6b:d5:8f, ipaddr=192.168.0.135, mask=255.255.255.0, gw=192.168.0.254 <6>[ 9.855298] host=192.168.0.135, domain=shed, nis-domain=(none) <6>[ 9.861862] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 9.861890] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 9.876206] clk: Disabling unused clocks <6>[ 9.880715] PM: genpd: Disabling unused power domains <6>[ 9.887825] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan2 for rx DMA transfers <6>[ 9.897528] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan3 for tx DMA transfers <6>[ 9.912666] Freeing unused kernel image (initmem) memory: 2048K <6>[ 9.919435] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.368468] udevd[74]: starting version 3.2.9 <27>[ 10.399774] udevd[74]: specified user 'tss' unknown <27>[ 10.405417] udevd[74]: specified group 'tss' unknown <30>[ 10.429440] udevd[75]: starting eudev-3.2.9 <4>[ 13.926535] mtdblock: MTD device 'at91bootstrap' is NAND, please consider using UBI block devices instead. <4>[ 13.938978] mtdblock: MTD device 'bootloader' is NAND, please consider using UBI block devices instead. <6>[ 13.974411] at91_i2c f8014000.i2c: using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers <4>[ 13.992402] mtdblock: MTD device 'bootloader env redundant' is NAND, please consider using UBI block devices instead. <4>[ 14.038510] mtdblock: MTD device 'bootloader env' is NAND, please consider using UBI block devices instead. <6>[ 14.061436] i2c i2c-0: using pinctrl states for GPIO recovery <6>[ 14.067581] i2c i2c-0: using generic GPIOs for recovery <6>[ 14.073416] at91_i2c f8014000.i2c: AT91 i2c bus driver (hw version: 0x502). <4>[ 14.082130] mtdblock: MTD device 'device tree' is NAND, please consider using UBI block devices instead. <4>[ 14.123689] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. <4>[ 14.167853] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. <6>[ 14.704012] atmel_spi fc018000.spi: Using dma0chan6 (tx) and dma0chan7 (rx) for DMA transfers <6>[ 14.809060] atmel_spi fc018000.spi: Atmel SPI Controller version 0x221 at 0xfc018000 (irq 36) <6>[ 14.947552] atmel_aes fc044000.crypto: version: 0x201 <6>[ 14.962807] iio iio:device0: Resolution used: 10 bits <6>[ 14.968114] iio iio:device0: ADC Touch screen is disabled. <6>[ 15.101536] atmel_aes fc044000.crypto: Atmel AES - Using dma1chan0, dma1chan1 for DMA transfers <6>[ 15.153334] atmel_tdes fc04c000.crypto: version: 0x702 <6>[ 15.183903] atmel_sha fc050000.crypto: version: 0x420 <6>[ 15.219452] atmel_tdes fc04c000.crypto: using dma1chan2, dma1chan3 for DMA transfers <6>[ 15.227495] atmel_tdes fc04c000.crypto: Atmel DES/TDES <6>[ 15.234322] atmel_sha fc050000.crypto: using dma1chan4 for DMA transfers <6>[ 15.241489] atmel_sha fc050000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 15.340178] at91_rtc fc0686b0.rtc: registered as rtc0 <6>[ 15.345535] at91_rtc fc0686b0.rtc: setting system clock to 2012-01-01T00:00:30 UTC (1325376030) <6>[ 15.354682] at91_rtc fc0686b0.rtc: AT91 Real Time Clock driver. done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-3900408/environment / # /lava-3900408/bin/lava-test-runner /lava-3900408/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3900408/0/tests/0_dmesg + cat uuid + UUID=3900408_1<8>[. 18.913267] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 19.040114] <8>[ 19.152361] <8>[ 19.266190] + set +x <8>[ 19.280079] / #