Trying 192.168.56.175... Connected to arpeggi. Escape character is '^]'. ser2net port telnet,3001 device serialdev, /dev/serial/by-path/platform-1c1c000.usb-usb-0:1:1.3-port0, 115200n81, local=false [,115200N81] (Debian GNU/Linux) ! U-Boot SPL 2022.04-6.3.0+git.c71ae7141f30 (May 15 2023 - 16:20:01 +0000) DDRINFO: start DRAM init DDRINFO: DRAM rate 4000MTS Training FAILED DDRINFO: start DRAM init DDRINFO: DRAM rate 4000MTS DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done DDR configured as single rank SEC0: RNG instantiated Normal Boot WDT: Started watchdog@30280000 with servicing (60s timeout) Trying to boot from BOOTROM Boot Stage: Primary boot Find img info 0x&4802d800, size 888 Download 916480, Total size 917440 NOTICE: BL31: v2.6(release):lf_v2.6-g3c1583ba0a NOTICE: BL31: Built : 11:00:38, Nov 21 2022 U-Boot 2022.04-6.3.0+git.c71ae7141f30 (May 15 2023 - 16:20:01 +0000) CPU: i.MX8MP[8] rev1.1 1600 MHz (running at 1200 MHz) CPU: Industrial temperature grade (-40C to 105C) at 38C Reset cause: POR DRAM: 4 GiB Core: 89 devices, 23 uclasses, devicetree: separate WDT: Started watchdog@30280000 with servicing (60s timeout) MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@30880000 Out: serial@30880000 Err: serial@30880000 Model: Toradex 0063 Verdin iMX8M Plus Quad 4GB IT V1.1A Serial#: 15034401 Carrier: Toradex Dahlia V1.1C, Serial# 11080179 SEC0: RNG instantiated BuildInfo: - ATF 3c1583b Net: eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME] Normal Boot Hit any key to stop autoboot: 1  0 Verdin iMX8MP # setenv autoload no setenv autoload no Verdin iMX8MP # dhcp dhcp ethernet@30bf0000 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.6.29 (862 ms) Verdin iMX8MP # setenv serverip 192.168.6.3 setenv serverip 192.168.6.3 Verdin iMX8MP # tftp 0x40400000 921924/tftp-deploy-st5z1pe2/kernel/Image tftp 0x40400000 921924/tftp-deploy-st5z1pe2/kernel/Image Using ethernet@30bf0000 device TFTP from server 192.168.6.3; our IP address is 192.168.6.29 Filename '921924/tftp-deploy-st5z1pe2/kernel/Image'. Load address: 0x40400000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 32.2 MiB/s done Bytes transferred = 45908480 (2bc8200 hex) Verdin iMX8MP # tftp 0x45000000 921924/tftp-deploy-st5z1pe2/ramdisk/ramdisk.cpio.gz.uboot tftp 0x45000000 921924/tftp-deploy-st5z1pe2/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@30bf0000 device TFTP from server 192.168.6.3; our IP address is 192.168.6.29 Filename '921924/tftp-deploy-st5z1pe2/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x45000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################################### 32 MiB/s done Bytes transferred = 23442743 (165b537 hex) Verdin iMX8MP # setenv initrd_size ${filesize} setenv initrd_size ${filesize} Verdin iMX8MP # tftp 0x44000000 921924/tftp-deploy-st5z1pe2/dtb/imx8mp-verdin-nonwifi-dahlia.dtb tftp 0x44000000 921924/tftp-deploy-st5z1pe2/dtb/imx8mp-verdin-nonwifi-dahlia.dtb Using ethernet@30bf0000 device TFTP from server 192.168.6.3; our IP address is 192.168.6.29 Filename '921924/tftp-deploy-st5z1pe2/dtb/imx8mp-verdin-nonwifi-dahlia.dtb'. Load address: 0x44000000 Loading: *## 15.3 MiB/s done Bytes transferred = 64345 (fb59 hex) Verdin iMX8MP # setenv bootargs 'console=ttymxc2,115200 earlycon,115200n8 root=/dev/nfs rw nfsroot=192.168.6.3:/var/lib/lava/dispatcher/tmp/921924/extract-nfsrootfs-oxwa7z86,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc2,115200 earlycon,115200n8 root=/dev/nfs rw nfsroot=192.168.6.3:/var/lib/lava/dispatcher/tmp/921924/extract-nfsrootfs-oxwa7z86,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' Verdin iMX8MP # booti 0x40400000 0x45000000 0x44000000 booti 0x40400000 0x45000000 0x44000000 ## Loading init Ramdisk from Legacy Image at 45000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 23442679 Bytes = 22.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 44000000 Booting using the fdt blob at 0x44000000 Loading Device Tree to 00000000ffaf0000, end 00000000ffb02b58 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.12.0-rc5-next-20241101 (KernelCI@build-j358953-arm64-gcc-12-defconfig-4x8l9) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Nov 1 09:03:28 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Toradex Verdin iMX8M Plus on Dahlia Board [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x0000000030880000 (options '') [ 0.000000] printk: legacy bootconsole [ec_imx6q0] enabled [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x000000013fffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x13f7a95c0-0x13f7abbff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000013fffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fda00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 24 pages/cpu s61336 r8192 d28776 u98304 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttymxc2,115200 earlycon,115200n8 root=/dev/nfs rw nfsroot=192.168.6.3:/var/lib/lava/dispatcher/tmp/921924/extract-nfsrootfs-oxwa7z86,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters "earlycon,115200n8", will be passed to user space. <6>[ 0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1048576 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 4. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f9a00000-0x00000000fda00000] (64MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 160 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=1 <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 <4>[ 0.000000] ITS: No ITS available, not enabling LPIs <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000000] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.010365] Console: colour dummy device 80x25 <6>[ 0.013117] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) <6>[ 0.023634] pid_max: default: 32768 minimum: 301 <6>[ 0.028596] LSM: initializing lsm=capability <6>[ 0.033191] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.040789] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.069021] rcu: Hierarchical SRCU implementation. <6>[ 0.071236] rcu: Max phase no-delay instances is 1000. <6>[ 0.076977] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.088746] EFI services will not be available. <6>[ 0.094742] smp: Bringing up secondary CPUs ... <6>[ 0.097169] Detected VIPT I-cache on CPU1 <6>[ 0.097233] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 <6>[ 0.097268] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.097846] Detected VIPT I-cache on CPU2 <6>[ 0.097892] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 <6>[ 0.097913] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] <6>[ 0.098443] Detected VIPT I-cache on CPU3 <6>[ 0.098490] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 <6>[ 0.098511] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] <6>[ 0.098622] smp: Brought up 1 node, 4 CPUs <6>[ 0.155941] SMP: Total of 4 processors activated. <6>[ 0.160922] CPU: All CPU(s) started at EL2 <6>[ 0.165336] CPU features: detected: 32-bit EL0 Support <6>[ 0.170724] CPU features: detected: 32-bit EL1 Support <6>[ 0.176157] CPU features: detected: CRC32 instructions <6>[ 0.181603] alternatives: applying system-wide alternatives <6>[ 0.188609] Memory: 3940440K/4194304K available (17344K kernel code, 4896K rwdata, 11948K rodata, 10496K init, 744K bss, 216548K reserved, 32768K cma-reserved) <6>[ 0.203183] devtmpfs: initialized <6>[ 0.217336] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.224579] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.232486] 21344 pages in range for non-PLT usage <6>[ 0.232503] 512864 pages in range for PLT usage <6>[ 0.237046] pinctrl core: initialized pinctrl subsystem <6>[ 0.250711] DMI not present or invalid. <6>[ 0.254532] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.259084] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.265719] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.273819] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.281847] audit: initializing netlink subsys (disabled) <5>[ 0.287661] audit: type=2000 audit(0.184:1): state=initialized audit_enabled=0 res=1 <6>[ 0.289546] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.295550] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.301912] cpuidle: using governor menu <6>[ 0.313126] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.320039] ASID allocator initialised with 65536 entries <6>[ 0.328491] Serial: AMBA PL011 UART driver <6>[ 0.341008] platform soc@0: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000/unique-id@8 <6>[ 0.349184] platform funnel: Fixed dependency cycle(s) with /soc@0/etm@28440000 <6>[ 0.355791] amba 28440000.etm: Fixed dependency cycle(s) with /funnel <6>[ 0.362561] platform funnel: Fixed dependency cycle(s) with /soc@0/etm@28540000 <6>[ 0.370110] amba 28540000.etm: Fixed dependency cycle(s) with /funnel <6>[ 0.376908] platform funnel: Fixed dependency cycle(s) with /soc@0/etm@28640000 <6>[ 0.384458] amba 28640000.etm: Fixed dependency cycle(s) with /funnel <6>[ 0.391261] platform funnel: Fixed dependency cycle(s) with /soc@0/etm@28740000 <6>[ 0.398823] amba 28740000.etm: Fixed dependency cycle(s) with /funnel <6>[ 0.405639] platform funnel: Fixed dependency cycle(s) with /soc@0/funnel@28c03000 <6>[ 0.413400] amba 28c03000.funnel: Fixed dependency cycle(s) with /soc@0/etf@28c04000 <6>[ 0.421416] amba 28c03000.funnel: Fixed dependency cycle(s) with /funnel <6>[ 0.428538] amba 28c03000.funnel: Fixed dependency cycle(s) with /soc@0/etf@28c04000 <6>[ 0.436499] amba 28c04000.etf: Fixed dependency cycle(s) with /soc@0/etr@28c06000 <6>[ 0.444258] amba 28c04000.etf: Fixed dependency cycle(s) with /soc@0/funnel@28c03000 <6>[ 0.452421] amba 28c04000.etf: Fixed dependency cycle(s) with /soc@0/etr@28c06000 <6>[ 0.460151] amba 28c06000.etr: Fixed dependency cycle(s) with /soc@0/etf@28c04000 <6>[ 0.472073] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpiohog3grp <6>[ 0.480264] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpiohog2grp <6>[ 0.491287] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpiohog1grp <6>[ 0.502309] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpio8grp <6>[ 0.513078] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpio7grp <6>[ 0.523836] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpio4grp <6>[ 0.534599] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpio3grp <6>[ 0.545359] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpio2grp <6>[ 0.556123] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/gpio1grp <6>[ 0.567644] imx8mp-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.575236] platform 30350000.efuse: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 <6>[ 0.586940] platform 30350000.efuse: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 <6>[ 0.596318] platform 30380000.clock-controller: Fixed dependency cycle(s) with /soc@0/interrupt-controller@38800000 <6>[ 0.627079] platform 32fc4000.display-bridge: Fixed dependency cycle(s) with /soc@0/bus@32c00000/hdmi@32fd8000 <6>[ 0.634613] platform 32fc4000.display-bridge: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-controller@32fc6000 <6>[ 0.646591] platform 32fc4000.display-bridge: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-controller@32fc6000 <6>[ 0.657777] platform 32fc6000.display-controller: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-bridge@32fc4000 <6>[ 0.669815] platform 32fc4000.display-bridge: Fixed dependency cycle(s) with /soc@0/bus@32c00000/hdmi@32fd8000 <6>[ 0.679703] platform 32fd8000.hdmi: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-bridge@32fc4000 <6>[ 0.696724] platform connector: Fixed dependency cycle(s) with /soc@0/usb@32f10100/usb@38100000 <6>[ 0.706951] platform 32fd8000.hdmi: Fixed dependency cycle(s) with /native-hdmi-connector <6>[ 0.712750] platform native-hdmi-connector: Fixed dependency cycle(s) with /soc@0/bus@32c00000/hdmi@32fd8000 <6>[ 0.725031] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.729839] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.736393] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.743476] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.750038] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.757126] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.763699] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.770774] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.779616] ACPI: Interpreter disabled. <6>[ 0.785508] iommu: Default domain type: Translated <6>[ 0.787726] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.794533] SCSI subsystem initialized <6>[ 0.798597] usbcore: registered new interface driver usbfs <6>[ 0.804046] usbcore: registered new interface driver hub <6>[ 0.809633] usbcore: registered new device driver usb <6>[ 0.816703] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.820199] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.829656] PTP clock support registered <6>[ 0.834011] EDAC MC: Ver: 3.0.0 <6>[ 0.837727] scmi_core: SCMI protocol bus registered <6>[ 0.843867] FPGA manager framework <6>[ 0.846182] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.853475] vgaarb: loaded <6>[ 0.855911] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.862079] VFS: Disk quotas dquot_6.6.0 <6>[ 0.866063] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.873447] pnp: PnP ACPI: disabled <6>[ 0.884430] NET: Registered PF_INET protocol family <6>[ 0.886900] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.897199] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.903346] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.911341] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.919759] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.928115] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.934195] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.941164] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.948725] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.954881] RPC: Registered named UNIX socket transport module. <6>[ 0.960684] RPC: Registered udp transport module. <6>[ 0.965667] RPC: Registered tcp transport module. <6>[ 0.970651] RPC: Registered tcp-with-tls transport module. <6>[ 0.976427] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.983174] PCI: CLS 0 bytes, default 64 <6>[ 0.987547] Unpacking initramfs... <6>[ 0.994730] kvm [1]: nv: 557 coarse grained trap handlers <6>[ 0.998057] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.004723] kvm [1]: GICv3: no GICV resource entry <6>[ 1.007197] kvm [1]: disabling GICv2 emulation <6>[ 1.011961] kvm [1]: GIC system register CPU interface enabled <6>[ 1.018089] kvm [1]: vgic interrupt IRQ9 <6>[ 1.022289] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 1.033266] Initialise system trusted keyrings <6>[ 1.035361] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.042242] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.048385] NFS: Registering the id_resolver key type <5>[ 1.053415] Key type id_resolver registered <5>[ 1.057829] Key type id_legacy registered <6>[ 1.062145] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.069129] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.077097] 9p: Installing v9fs 9p2000 file system support <5>[ 1.136025] Key type asymmetric registered <5>[ 1.137560] Asymmetric key parser 'x509' registered <6>[ 1.142836] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.150433] io scheduler mq-deadline registered <6>[ 1.155243] io scheduler kyber registered <6>[ 1.159575] io scheduler bfq registered <6>[ 1.182667] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.224860] SoC: i.MX8MP revision 1.1 <6>[ 1.276154] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.285657] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 15, base_baud = 1500000) is a IMX <6>[ 1.292866] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 16, base_baud = 1500000) is a IMX <6>[ 1.301089] printk: console [ttymxc2] enabled <6>[ 1.301089] printk: console [ttymxc2] enabled <6>[ 1.310251] printk: legacy bootconsole [ec_imx6q0] disabled <6>[ 1.310251] printk: legacy bootconsole [ec_imx6q0] disabled <6>[ 1.325149] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 17, base_baud = 1500000) is a IMX <6>[ 1.326397] msm_serial: driver initialized <6>[ 1.327151] SuperH (H)SCI(F) driver initialized <6>[ 1.327616] STM32 USART driver initialized <6>[ 1.339562] loop: module loaded <6>[ 1.341619] megasas: 07.727.03.00-rc1 <6>[ 1.354545] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.356628] thunder_xcv, ver 1.0 <6>[ 1.356671] thunder_bgx, ver 1.0 <6>[ 1.356704] nicpf, ver 1.0 <6>[ 1.359112] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.359121] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.359186] hclge is initializing <6>[ 1.359222] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.359227] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.359253] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.359256] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.359283] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.359286] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.359318] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.359322] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.359992] sky2: driver version 1.30 <6>[ 1.362702] VFIO - User Level meta-driver version: 0.3 <6>[ 1.368908] usbcore: registered new interface driver usb-storage <6>[ 1.374720] i2c_dev: i2c /dev entries driver <6>[ 1.393568] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.393577] sdhci: Copyright(c) Pierre Ossman <6>[ 1.395523] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.397621] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.404219] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... <6>[ 1.405865] usbcore: registered new interface driver usbhid <6>[ 1.405874] usbhid: USB HID core driver <6>[ 1.416859] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 (0,8000003f) counters available <6>[ 1.425078] platform soc@0: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000 <6>[ 1.436052] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <6>[ 1.436115] NET: Registered PF_PACKET protocol family <6>[ 1.436203] 9pnet: Installing 9P2000 support <5>[ 1.436269] Key type dns_resolver registered <6>[ 1.446430] registered taskstats version 1 <5>[ 1.446765] Loading compiled-in X.509 certificates <6>[ 1.454745] Demotion targets for Node 0: null <4>[ 1.469600] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 1.471420] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 1.473169] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 1.475079] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 1.477010] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 1.491645] reg-fixed-voltage regulator-pcie: nonexclusive access to GPIO for (default) <6>[ 1.492243] i2c i2c-0: using pinctrl states for GPIO recovery <6>[ 1.492319] i2c i2c-0: using generic GPIOs for recovery <6>[ 1.493237] i2c i2c-0: IMX I2C adapter registered <6>[ 1.494545] i2c i2c-1: using pinctrl states for GPIO recovery <6>[ 1.494610] i2c i2c-1: using generic GPIOs for recovery <6>[ 1.494683] i2c i2c-1: IMX I2C adapter registered <6>[ 1.495882] i2c i2c-2: using pinctrl states for GPIO recovery <6>[ 1.496028] i2c i2c-2: using generic GPIOs for recovery <6>[ 1.496100] i2c i2c-2: IMX I2C adapter registered <6>[ 1.497216] i2c i2c-3: using pinctrl states for GPIO recovery <6>[ 1.497274] i2c i2c-3: using generic GPIOs for recovery <6>[ 1.498227] i2c i2c-3: IMX I2C adapter registered <6>[ 1.499685] i2c i2c-4: using pinctrl states for GPIO recovery <6>[ 1.499745] i2c i2c-4: using generic GPIOs for recovery <6>[ 1.499814] i2c i2c-4: IMX I2C adapter registered <6>[ 1.533024] platform connector: Fixed dependency cycle(s) with /soc@0/usb@32f10100/usb@38100000 <6>[ 1.533107] platform 38100000.usb: Fixed dependency cycle(s) with /connector <4>[ 1.548813] imx8mq-usb-phy 381f0040.usb-phy: supply vbus not found, using dummy regulator <6>[ 1.562043] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.562069] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 1.562419] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x000080a001000010 <6>[ 1.562465] xhci-hcd xhci-hcd.0.auto: irq 202, io mem 0x38200000 <6>[ 1.562600] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.562611] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 1.562630] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 1.563269] hub 1-0:1.0: USB hub found <6>[ 1.563297] hub 1-0:1.0: 1 port detected <6>[ 1.566013] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 1.566548] hub 2-0:1.0: USB hub found <6>[ 1.566574] hub 2-0:1.0: 1 port detected <6>[ 1.597491] imx6q-pcie 33800000.pcie: host bridge /soc@0/pcie@33800000 ranges: <6>[ 1.597566] imx6q-pcie 33800000.pcie: IO 0x001ff80000..0x001ff8ffff -> 0x0000000000 <6>[ 1.597597] imx6q-pcie 33800000.pcie: MEM 0x0018000000..0x001fefffff -> 0x0018000000 <6>[ 1.599185] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 1.688002] mmc2: new HS400 Enhanced strobe MMC card at address 0001 <6>[ 1.693016] mmcblk2: mmc2:0001 IX2932 29.1 GiB <6>[ 1.697056] mmcblk2: p1 p2 <6>[ 1.698852] mmcblk2boot0: mmc2:0001 IX2932 4.00 MiB <6>[ 1.700574] mmcblk2boot1: mmc2:0001 IX2932 4.00 MiB <6>[ 1.702192] mmcblk2rpmb: mmc2:0001 IX2932 4.00 MiB, chardev (234:0) <6>[ 1.808499] imx6q-pcie 33800000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 16G <6>[ 1.816305] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 1.879676] nxp-pca9450 0-0025: pca9450bc probed. <6>[ 1.886934] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO <6>[ 1.926082] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <6>[ 2.012162] hub 1-1:1.0: USB hub found <6>[ 2.012821] hub 1-1:1.0: 4 ports detected <6>[ 2.084396] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd <6>[ 2.123576] Freeing initrd memory: 22888K <6>[ 2.123699] hub 2-1:1.0: USB hub found <6>[ 2.128270] hub 2-1:1.0: 3 ports detected <6>[ 2.356542] usb 1-1.4: new high-speed USB device number 3 using xhci-hcd <6>[ 2.768235] imx6q-pcie 33800000.pcie: Phy link never came up <6>[ 3.732245] imx6q-pcie 33800000.pcie: Phy link never came up <6>[ 3.732620] imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00 <6>[ 3.732632] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 3.732640] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 3.732648] pci_bus 0000:00: root bus resource [mem 0x18000000-0x1fefffff] <6>[ 3.732682] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 PCIe Root Port <6>[ 3.732700] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x000fffff] <6>[ 3.732714] pci 0000:00:00.0: ROM [mem 0x00000000-0x0000ffff pref] <6>[ 3.732723] pci 0000:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.732731] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] <6>[ 3.732738] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] <6>[ 3.732749] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] <6>[ 3.732802] pci 0000:00:00.0: supports D1 <6>[ 3.732808] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold <6>[ 3.735809] pci 0000:00:00.0: BAR 0 [mem 0x18000000-0x180fffff]: assigned <6>[ 3.735821] pci 0000:00:00.0: ROM [mem 0x18100000-0x1810ffff pref]: assigned <6>[ 3.735829] pci 0000:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.735840] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] <6>[ 3.735846] pci_bus 0000:00: resource 5 [mem 0x18000000-0x1fefffff] <6>[ 3.736265] pcieport 0000:00:00.0: PME: Signaling with IRQ 206 <6>[ 3.736586] pcieport 0000:00:00.0: AER: enabled with IRQ 206 <6>[ 3.736952] Trying to probe devices needed for running init ... <6>[ 16.012296] clk: Disabling unused clocks <6>[ 16.017085] PM: genpd: Disabling unused power domains <6>[ 16.017138] ALSA device list: <6>[ 16.017146] No soundcards found. <6>[ 16.020349] Freeing unused kernel memory: 10496K <6>[ 16.020435] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.22-1~deb12u1 <6>[ 16.757915] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 7 mkt segment 2 supported-hw 0x80 0x4 <6>[ 16.804617] cs_system_cfg: CoreSight Configuration manager initialised <6>[ 16.901663] caam 30900000.crypto: device ID = 0x0a16040100000100 (Era 9) <6>[ 16.904163] caam 30900000.crypto: job rings = 2, qi = 0 <6>[ 16.946978] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input1 <6>[ 16.963746] hwmon hwmon3: temp1_input not attached to any thermal zone <6>[ 16.963771] lm75 3-004f: hwmon3: sensor 'tmp75c' <6>[ 16.977970] wm8904 3-001a: revision A <4>[ 16.978046] ina2xx 3-0040: supply vs not found, using dummy regulator <6>[ 16.982403] CAN device driver interface <6>[ 16.996707] ina2xx 3-0040: power monitor ina219 (Rshunt = 10000 uOhm) <4>[ 17.003537] rtc-ds1307 0-0032: oscillator failed, set time! <6>[ 17.003995] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc1 <6>[ 17.004400] rtc-ds1307 0-0032: registered as rtc0 <6>[ 17.024753] imx-sdma 30bd0000.dma-controller: external firmware not found, using ROM firmware <3>[ 17.046278] rtc-ds1307 0-0032: hctosys: unable to read the hardware clock <6>[ 17.080007] etnaviv etnaviv: bound 38000000.gpu (ops gpu_ops [etnaviv]) <6>[ 17.084105] mc: Linux media interface: v0.10 <6>[ 17.087301] etnaviv etnaviv: bound 38008000.gpu (ops gpu_ops [etnaviv]) <6>[ 17.094784] etnaviv etnaviv: bound 38500000.npu (ops gpu_ops [etnaviv]) <6>[ 17.094911] etnaviv-gpu 38000000.gpu: model: GC7000, revision: 6204 <6>[ 17.095061] etnaviv-gpu 38008000.gpu: model: GC520, revision: 5341 <6>[ 17.095142] etnaviv-gpu 38500000.npu: model: GC8000, revision: 8002 <4>[ 17.095148] etnaviv-gpu 38500000.npu: etnaviv has been instantiated on a NPU, for which the UAPI is still experimental <6>[ 17.096067] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 <6>[ 17.108625] imx-sdma 30e00000.dma-controller: external firmware not found, using ROM firmware <6>[ 17.112853] imx8mp-dw-hdmi-tx 32fd8000.hdmi: Detected HDMI TX controller v2.13a with HDCP (SAMSUNG HDMI TX PHY) <6>[ 17.144165] videodev: Linux video capture interface: v2.00 <6>[ 17.191238] [drm] Initialized imx-lcdif 1.0.0 for 32fc6000.display-controller on minor 1 <6>[ 17.191321] imx-lcdif 32fc6000.display-controller: [drm] Cannot find any crtc or sizes <6>[ 17.202977] imx-sdma 30e10000.dma-controller: external firmware not found, using ROM firmware <6>[ 17.209686] hantro-vpu 38300000.video-codec: registered nxp,imx8mm-vpu-g1-dec as /dev/video0 <6>[ 17.215304] hantro-vpu 38310000.video-codec: registered nxp,imx8mq-vpu-g2-dec as /dev/video1 <6>[ 17.240507] usbcore: registered new device driver onboard-usb-dev <6>[ 17.248196] usb 1-1.4: USB disconnect, device number 3 <6>[ 17.252618] imx-dwmac 30bf0000.ethernet: IRQ eth_lpi not found <6>[ 17.252629] imx-dwmac 30bf0000.ethernet: IRQ sfty not found <6>[ 17.262320] imx-dwmac 30bf0000.ethernet: User ID: 0x10, Synopsys ID: 0x51 <6>[ 17.262338] imx-dwmac 30bf0000.ethernet: DWMAC4/5 <6>[ 17.262344] imx-dwmac 30bf0000.ethernet: DMA HW capability register supported <6>[ 17.262348] imx-dwmac 30bf0000.ethernet: RX Checksum Offload Engine supported <6>[ 17.262351] imx-dwmac 30bf0000.ethernet: Wake-Up On Lan supported <6>[ 17.262432] imx-dwmac 30bf0000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 17.262438] imx-dwmac 30bf0000.ethernet: Enabled L3L4 Flow TC (entries=8) <6>[ 17.262443] imx-dwmac 30bf0000.ethernet: Enabled RFS Flow TC (entries=10) <6>[ 17.262455] imx-dwmac 30bf0000.ethernet: Enabling HW TC (entries=256, max_off=256) <6>[ 17.262461] imx-dwmac 30bf0000.ethernet: Using 34/40 bits DMA host/device width <3>[ 17.274253] debugfs: File 'Headphone Jack' in directory 'dapm' already present! <3>[ 17.274277] debugfs: File 'CPU-Playback' in directory 'dapm' already present! <3>[ 17.274281] debugfs: File 'CPU-Capture' in directory 'dapm' already present! <6>[ 17.376954] imx-dwmac 30bf0000.ethernet end0: renamed from eth0 <6>[ 17.383625] caam algorithms registered in /proc/crypto <6>[ 17.383750] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 17.383759] caam 30900000.crypto: registering rng-caam <6>[ 17.389290] caam 30900000.crypto: rng crypto API alg registered prng-caam <5>[ 17.409376] random: crng init done <6>[ 17.532141] hub 1-1:1.0: USB hub found <6>[ 17.532793] hub 1-1:1.0: 4 ports detected <6>[ 17.691261] hub 1-1:1.0: USB hub found <6>[ 17.691331] hub 1-1:1.0: 4 ports detected <6>[ 17.851192] hub 1-1:1.0: USB hub found <6>[ 17.851264] hub 1-1:1.0: 4 ports detected <6>[ 18.043496] hub 2-1:1.0: USB hub found <6>[ 18.043496] hub 1-1:1.0: USB hub found <6>[ 18.043572] hub 1-1:1.0: 4 ports detected <6>[ 18.043890] hub 2-1:1.0: 3 ports detected <4>[ 18.079332] onboard-usb-dev 38200000.usb:usb-hub@1: supply vdd2 not found, using dummy regulator <6>[ 18.155260] hub 2-1:1.0: USB hub found <6>[ 18.155363] hub 2-1:1.0: 3 ports detected Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/end0 found done. Begin: Waiting up to 180 secs for any network device to become available ... done. IP-Config: end0 hardware address 00:14:2d:e5:68:21 mtu 150<6>[ 18.262498] imx-dwmac 30bf0000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-0 0 DHCP <6>[ 18.263188] imx-dwmac 30bf0000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-1 <6>[ 18.263884] imx-dwmac 30bf0000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-2 <6>[ 18.264422] imx-dwmac 30bf0000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-3 <6>[ 18.265249] imx-dwmac 30bf0000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-4 <6>[ 18.328916] imx-dwmac 30bf0000.ethernet end0: PHY [stmmac-0:07] driver [Microchip KSZ9131 Gigabit PHY] (irq=35) <6>[ 18.340914] imx-dwmac 30bf0000.ethernet end0: No Safety Features support found <6>[ 18.340949] imx-dwmac 30bf0000.ethernet end0: IEEE 1588-2008 Advanced Timestamp supported <6>[ 18.341557] imx-dwmac 30bf0000.ethernet end0: registered PTP clock <6>[ 18.348838] imx-dwmac 30bf0000.ethernet end0: configuring for phy/rgmii-id link mode <6>[ 18.396233] usb 1-1.4: new high-speed USB device number 4 using xhci-hcd IP-Config: no response after 2 secs - giving up IP-Config: end0 hardware address 00:14:2d:e5:68:21 mtu 1500 DHCP <6>[ 21.358595] imx-dwmac 30bf0000.ethernet end0: Link is Up - 1Gbps/Full - flow control off IP-Config: no response after 3 secs - giving up IP-Config: end0 hardware address 00:14:2d:e5:68:21 mtu 1500 DHCP IP-Config: end0 guessed broadcast address 192.168.6.255 IP-Config: end0 complete (dhcp from 192.168.6.1): address: 192.168.6.29 broadcast: 192.168.6.255 netmask: 255.255.255.0 gateway: 192.168.6.1 dns0 : 10.255.253.1 dns1 : 0.0.0.0 rootserver: 192.168.6.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 23.434485] systemd[1]: System time before build time, advancing clock. <6>[ 23.489931] NET: Registered PF_INET6 protocol family <6>[ 23.491564] Segment Routing with IPv6 <6>[ 23.491597] In-situ OAM (IOAM) with IPv6 <30>[ 23.549475] systemd[1]: systemd 252.22-1~deb12u1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) <30>[ 23.549517] systemd[1]: Detected architecture arm64. Welcome to [1mDebian GNU/Linux 12 (bookworm)[0m! <30>[ 23.602502] systemd[1]: Hostname set to . <30>[ 24.472319] systemd[1]: Queued start job for default target graphical.target. [[0;32m OK [0m] Created slice<30>[ 24.499405] systemd[1]: Created slice system-getty.slice - Slice /system/getty. [0;1;39msystem-getty.slice[0m - Slice /system/getty. [[0;32m OK [0m] Created slice<30>[ 24.521516] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe. [0;1;39msystem-modpr…lice[0m - Slice /system/modprobe. [[0;32m OK [0m] Created slice<30>[ 24.546215] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty. [0;1;39msystem-seria…[0m - Slice /system/serial-getty. [[0;32m OK [0m] Created slice<30>[ 24.569163] systemd[1]: Created slice user.slice - User and Session Slice. [0;1;39muser.slice[0m - User and Session Slice. [[0;32m OK [0m] Started [0;1<30>[ 24.588662] systemd[1]: Started systemd-ask-password-console.path - Dispatch Password Requests to Console Directory Watch. ;39msystemd-ask-passwo…quests to Console Directory Watch. <30>[ 24.612634] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39msystemd-ask-passwo… Requests to Wall Directory Watch. Expecting device [0;1;3<30>[ 24.636551] systemd[1]: proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point was skipped because of an unmet condition check (ConditionPathExists=/proc/sys/fs/binfmt_misc). 9mdev-ttymxc2.device[0m - /dev/t<30>[ 24.636654] systemd[1]: Expecting device dev-ttymxc2.device - /dev/ttymxc2... tymxc2... [[0;32m OK [0m] Reached targe<30>[ 24.676083] systemd[1]: Reached target cryptsetup.target - Local Encrypted Volumes. t [0;1;39mcryptsetup.…get[0m - Local Encrypted Volumes. [[0;32m OK [0m] Reached targe<30>[ 24.700466] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes. t [0;1;39mintegrityse…Local Integrity Protected Volumes. [[0;32m OK [0m] Reached targe<30>[ 24.724437] systemd[1]: Reached target paths.target - Path Units. t [0;1;39mpaths.target[0m - Path Units. [[0;32m OK [0m] Reached targe<30>[ 24.744402] systemd[1]: Reached target remote-fs.target - Remote File Systems. t [0;1;39mremote-fs.target[0m - Remote File Systems. [[0;32m OK [0m] Reached targe<30>[ 24.764383] systemd[1]: Reached target slices.target - Slice Units. t [0;1;39mslices.target[0m - Slice Units. [[0;32m OK [0m] Reached targe<30>[ 24.784434] systemd[1]: Reached target swap.target - Swaps. t [0;1;39mswap.target[0m - Swaps. [[0;32m OK [0m] Reached targe<30>[ 24.804441] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes. t [0;1;39mveritysetup… - Local Verity Protected Volumes. [[0;32m OK [0m] Listening on <30>[ 24.828735] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe. [0;1;39msystemd-initc… initctl Compatibility Named Pipe. <30>[ 24.854761] systemd[1]: Listening on systemd-journald-audit.socket - Journal Audit Socket. [[0;32m OK [0m] Listening on [0;1;39msystemd-journ…socket[0m - Journal Audit Socket. <30>[ 24.878444] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39msystemd-journ…t[0m - Journal Socket (/dev/log). [[0;32m OK [0m] Listening on <30>[ 24.900661] systemd[1]: Listening on systemd-journald.socket - Journal Socket. [0;1;39msystemd-journald.socket[0m - Journal Socket. [[0;32m OK [0m] Listening on <30>[ 24.922279] systemd[1]: Listening on systemd-networkd.socket - Network Service Netlink Socket. [0;1;39msystemd-netwo… - Network Service Netlink Socket. [[0;32m OK [0m] Listening on <30>[ 24.948394] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket. [0;1;39msystemd-udevd….socket[0m - udev Control Socket. [[0;32m OK [0m] Listening on <30>[ 24.972535] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket. [0;1;39msystemd-udevd…l.socket[0m - udev Kernel Socket. Mounting [0;1;39mdev-hu<30>[ 25.020717] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System... gepages.mount[0m - Huge Pages File System... <30>[ 25.043519] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System... Mounting [0;1;39mdev-mqueue.mount…POSIX Message Queue File System... <30>[ 25.067607] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System... Mounting [0;1;39msys-kernel-debug.…[0m - Kernel Debug File System... <30>[ 25.088543] systemd[1]: sys-kernel-tracing.mount - Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing). Starting [0;1;39mkmod-s<30>[ 25.093146] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes... tatic-nodes…ate List of Static Device Nodes... <30>[ 25.127264] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs... Starting [0;1;39mmodprobe@configfs…m - Load Kernel Module configfs... <30>[ 25.152050] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod... Starting [0;1;39mmodprobe@dm_mod.s…[0m - Load Kernel Module dm_mod... Starting [0;1;39mmodpro<30>[ 25.176117] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm... be@drm.service[0m - Load Kernel Module drm... <6>[ 25.197056] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev <30>[ 25.200743] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore... Starting [0;1;39mmodprobe@efi_psto…- Load Kernel Module efi_pstore... <30>[ 25.232295] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse... Starting [0;1;39mmodprobe@fuse.ser…e[0m - Load Kernel Module fuse... <30>[ 25.255837] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop... Starting [0;1;39mmodprobe@loop.ser…e[0m - Load Kernel Module loop... <6>[ 25.271153] fuse: init (API version 7.41) <30>[ 25.285468] systemd[1]: Starting systemd-journald.service - Journal Service... Starting [0;1;39msystemd-journald.service[0m - Journal Service... <30>[ 25.315469] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules... Starting [0;1;39msystemd-modules-l…rvice[0m - Load Kernel Modules... <30>[ 25.340082] systemd[1]: Starting systemd-network-generator.service - Generate network units from Kernel command line... Starting [0;1;39msystemd-network-g… units from Kernel command line... <30>[ 25.368236] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems... Starting [0;1;39msystemd-remount-f…nt Root and Kernel File Systems... <30>[ 25.395296] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices... Starting [0;1;39msystemd-udev-trig…[0m - Coldplug All udev Devices... <30>[ 25.420733] systemd[1]: Mounted dev-hugepages.mount - Huge Pages File System. [[0;32m OK [0m] Mounted [0;1;39mdev-hugepages.mount[0m - Huge Pages File System. <30>[ 25.440668] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System. [[0;32m OK [0m] Mounted [0;1;39mdev-mqueue.mount[…- POSIX Message Queue File System. <30>[ 25.460503] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39msys-kernel-debug.m…nt[0m - Kernel Debug File System. [[0;32m OK [0m] Finished [0;<30>[ 25.490593] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes. 1;39mkmod-static-nodes…reate List of Static Device Nodes. <30>[ 25.512686] systemd[1]: Started systemd-journald.service - Journal Service. [[0;32m OK [0m] Started [0;1;39msystemd-journald.service[0m - Journal Service. [[0;32m OK [0m] Finished [0;1;39mmodprobe@configfs…[0m - Load Kernel Module configfs. [[0;32m OK [0m] Finished [0;1;39mmodprobe@dm_mod.s…e[0m - Load Kernel Module dm_mod. [[0;32m OK [0m] Finished [0;1;39mmodprobe@drm.service[0m - Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mmodprobe@efi_psto…m - Load Kernel Module efi_pstore. [[0;32m OK [0m] Finished [0;1;39mmodprobe@fuse.service[0m - Load Kernel Module fuse. [[0;32m OK [0m] Finished [0;1;39mmodprobe@loop.service[0m - Load Kernel Module loop. [[0;32m OK [0m] Finished [0;1;39msystemd-modules-l…service[0m - Load Kernel Modules. [[0;32m OK [0m] Finished [0;1;39msystemd-network-g…rk units from Kernel command line. [[0;32m OK [0m] Finished [0;1;39msystemd-remount-f…ount Root and Kernel File Systems. [[0;32m OK [0m] Reached target [0;1;39mnetwork-pre…get[0m - Preparation for Network. Mounting [0;1;39msys-fs-fuse-conne…[0m - FUSE Control File System... Mounting [0;1;39msys-kernel-config…ernel Configuration File System... Starting [0;1;39msystemd-journal-f…h Journal to Persistent Storage... Starting [0;1;39msystemd-random-se…ice[0m - Load/Save Random Seed... Starting [0;1;39msystemd-sysctl.se…ce[0m - Apply Kernel Variables... <46>[ 25.793781] systemd-journald[231]: Received client request to flush runtime journal. Starting [0;1;39msystemd-sysusers.…rvice[0m - Create System Users... [[0;32m OK [0m] Mounted [0;1;39msys-fs-fuse-connec…nt[0m - FUSE Control File System. [[0;32m OK [0m] Mounted [0;1;39msys-kernel-config.… Kernel Configuration File System. [[0;32m OK [0m] Finished [0;1;39msystemd-random-se…rvice[0m - Load/Save Random Seed. [[0;32m OK [0m] Finished [0;1;39msystemd-sysctl.service[0m - Apply Kernel Variables. [[0;32m OK [0m] Finished [0;1;39msystemd-sysusers.service[0m - Create System Users. Starting [0;1;39msystemd-tmpfiles-…ate Static Device Nodes in /dev... [[0;32m OK [0m] Finished [0;1;39msystemd-journal-f…ush Journal to Persistent Storage. [[0;32m OK [0m] Finished [0;1;39msystemd-tmpfiles-…reate Static Device Nodes in /dev. [[0;32m OK [0m] Reached target [0;1;39mlocal-fs-pr…reparation for Local File Systems. [[0;32m OK [0m] Reached target [0;1;39mlocal-fs.target[0m - Local File Systems. Starting [0;1;39msystemd-tmpfiles-… Volatile Files and Directories... Starting [0;1;39msystemd-udevd.ser…ger for Device Events and Files... [[0;32m OK [0m] Finished [0;1;39msystemd-udev-trig…e[0m - Coldplug All udev Devices. [[0;32m OK [0m] Finished [0;1;39msystemd-tmpfiles-…te Volatile Files and Directories. Starting [0;1;39msystemd-timesyncd… - Network Time Synchronization... Starting [0;1;39msystemd-update-ut…rd System Boot/Shutdown in UTMP... [[0;32m OK [0m] Started [0;1;39msystemd-udevd.serv…nager for Device Events and Files. Starting [0;1;39msystemd-networkd.…ice[0m - Network Configuration... [[0;32m OK [0m] Finished [0;1;39msystemd-update-ut…cord System Boot/Shutdown in UTMP. [[0;32m OK [0m] Found device [0;1;39mdev-ttymxc2.device[0m - /dev/ttymxc2. [[0;32m OK [0m] Started [0;1;39msystemd-timesyncd.…0m - Network Time Synchronization. <5>[ 26.880628] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 26.921571] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <5>[ 26.923017] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 26.923805] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 26.923826] cfg80211: failed to load regulatory.db [[0;32m OK [0m] Reached target [0;1;39msysinit.target[0m - System Initialization. [[0;32m OK [0m] Started [0;1;39msystemd-tmpfiles-c… Cleanup of Temporary Directories. [[0;32m OK [0m] Reached target [0;1;39mtime-set.target[0m - System Time Set. [[0;32m OK [0m] Started [0;1;39mapt-daily.timer[0m - Daily apt download activities. [[0;32m OK [0m] Started [0;1;39mapt-daily-upgrade.… apt upgrade and clean activities. [[0;32m OK [0m] Started [0;1;39mdpkg-db-backup.tim… Daily dpkg database backup timer. [[0;32m OK [0m] Started [0;1;39me2scrub_all.timer…etadata Check for All Filesystems. [[0;32m OK [0m] Started [0;1;39mfstrim.timer[0m - Discard unused blocks once a week. [[0;32m OK [0m] Reached target [0;1;39mtimers.target[0m - Timer Units. [[0;32m OK [0m] Listening on [0;1;39mdbus.socket[…- D-Bus System Message Bus Socket. [[0;32m OK [0m] Reached target [0;1;39msockets.target[0m - Socket Units. [[0;32m OK [0m] Reached target [0;1;39mbasic.target[0m - Basic System. Starting [0;1;39mdbus.service[0m - D-Bus System Message Bus... <46>[ 27.173512] systemd-journald[231]: Oldest entry in /var/log/journal/44a983756b26438995e691b947c527e4/system.journal is older than the configured file retention duration (1month), suggesting rotation. <46>[ 27.173566] systemd-journald[231]: /var/log/journal/44a983756b26438995e691b947c527e4/system.journal: Journal header limits reached or header out-of-date, rotating. Starting [0;1;39me2scrub_reap.serv…e ext4 Metadata Check Snapshots... Starting [0;1;39msystemd-logind.se…ice[0m - User Login Management... [[0;32m OK [0m] Started [0;1;39msystemd-networkd.service[0m - Network Configuration. [[0;32m OK [0m] Reached target [0;1;39mnetwork.target[0m - Network. Starting [0;1;39mdpkg-db-backup.se…ly dpkg database backup service... Starting [0;1;39msystemd-user-sess…vice[0m - Permit User Sessions... [[0;32m OK [0m] Started [0;1;39mdbus.service[0m - D-Bus System Message Bus. [[0;32m OK [0m] Finished [0;1;39msystemd-user-sess…ervice[0m - Permit User Sessions. [[0;32m OK [0m] Started [0;1;39mgetty@tty1.service[0m - Getty on tty1. [[0;32m OK [0m] Started [0;1;39mserial-getty@ttymx…ice[0m - Serial Getty on ttymxc2. [[0;32m OK [0m] Reached target [0;1;39mgetty.target[0m - Login Prompts. [[0;32m OK [0m] Finished [0;1;39me2scrub_reap.serv…ine ext4 Metadata Check Snapshots. [[0;32m OK [0m] Started [0;1;39msystemd-logind.service[0m - User Login Management. [[0;32m OK [0m] Reached target [0;1;39mmulti-user.target[0m - Multi-User System. [[0;32m OK [0m] Reached target [0;1;39mgraphical.target[0m - Graphical Interface. Starting [0;1;39msystemd-update-ut… Record Runlevel Change in UTMP... [[0;32m OK [0m] Finished [0;1;39msystemd-update-ut… - Record Runlevel Change in UTMP. [[0;32m OK [0m] Reached target [0;1;39musb-gadget.…m - Hardware activated USB gadget. Starting [0;1;39malsa-restore.serv…- Save/Restore Sound Card State... [[0;32m OK [0m] Finished [0;1;39malsa-restore.serv…m - Save/Restore Sound Card State. [[0;32m OK [0m] Reached target [0;1;39msound.target[0m - Sound Card. [[0;32m OK [0m] Listening on [0;1;39msystemd-rfkil…l Switch Status /dev/rfkill Watch. [[0;32m OK [0m] Finished [0;1;39mdpkg-db-backup.se…aily dpkg database backup service. Debian GNU/Linux 12 debian-bookworm-arm64 ttymxc2 debian-bookworm-arm64 login: root (automatic login) Linux debian-bookworm-arm64 6.12.0-rc5-next-20241101 #1 SMP PREEMPT Fri Nov 1 09:03:28 UTC 2024 aarch64 The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/921924/extract-nfsrootfs-oxwa7z86' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/921924/extract-nfsrootfs-oxwa7z86' / # export NFS_SERVER_IP='192.168.6.3' export NFS_SERVER_IP='192.168.6.3' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-921924/environment . /lava-921924/environment / # /lava-921924/bin/lava-test-runner /lava-921924/0 /lava-921924/bin/lava-test-runner /lava-921924/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-921924/0/tests/0_timesync-off ++ cat uuid + UUID=921924_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-clone3 + TESTRUN_ID=1_kselftest-clone3 + cd /lava-921924/0/tests/1_kselftest-clone3 ++ cat uuid + UUID=921924_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c clone3 -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/next/master/next-20241101/arm64/defconfig/gcc-12/kselftest.tar.xz -L '' -S /dev/null -b imx8mp-verdin-nonwifi-dahlia -g next -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 -E '' INFO: install_deps skipped --2024-11-02 06:13:48-- http://storage.kernelci.org/next/master/next-20241101/arm64/defconfig/gcc-12/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 5368928 (5.1M) [application/octet-stream] Saving to: 'kselftest_armhf.tar.gz' kselftest_armhf.tar 0%[ ] 0 --.-KB/s kselftest_armhf.tar 0%[ ] 47.54K 177KB/s kselftest_armhf.tar 4%[ ] 218.67K 406KB/s kselftest_armhf.tar 17%[==> ] 893.67K 1.08MB/s kselftest_armhf.tar 68%[============> ] 3.51M 3.26MB/s kselftest_armhf.tar 100%[===================>] 5.12M 4.63MB/s in 1.1s 2024-11-02 06:13:50 (4.63 MB/s) - 'kselftest_armhf.tar.gz' saved [5368928/5368928] skiplist: ======================================== ======================================== clone3:clone3 clone3:clone3_clear_sighand clone3:clone3_set_tid clone3:clone3_cap_checkpoint_restore ============== Tests to run =============== clone3:clone3 clone3:clone3_clear_sighand clone3:clone3_set_tid clone3:clone3_cap_checkpoint_restore ===========End Tests to run =============== shardfile-clone3 pass <12>[ 55.310432] kselftest: Running tests in clone3 TAP version 13 1..4 # timeout set to 45 # selftests: clone3: clone3 # TAP version 13 # 1..19 # # clone3() syscall supported # # Running test 'simple clone3()' # # [490] Trying clone3() with flags 0 (size 0) # # I am the parent (490). My child's pid is 491 # # I am the child, my PID is 491 # # [490] clone3() with flags says: 0 expected 0 # ok 1 simple clone3() # # Running test 'clone3() in a new PID_NS' # # [490] Trying clone3() with flags 0x20000000 (size 0) # # I am the parent (490). My child's pid is 492 # # I am the child, my PID is 1 # # [490] clone3() with flags says: 0 expected 0 # ok 2 clone3() in a new PID_NS # # Running test 'CLONE_ARGS_SIZE_VER0' # # [490] Trying clone3() with flags 0 (size 64) # # I am the parent (490). My child's pid is 493 # # I am the child, my PID is 493 # # [490] clone3() with flags says: 0 expected 0 # ok 3 CLONE_ARGS_SIZE_VER0 # # Running test 'CLONE_ARGS_SIZE_VER0 - 8' # # [490] Trying clone3() with flags 0 (size 56) # # Invalid argument - Failed to create new process # # [490] clone3() with flags says: -22 expected -22 # ok 4 CLONE_ARGS_SIZE_VER0 - 8 # # Running test 'sizeof(struct clone_args) + 8' # # [490] Trying clone3() with flags 0 (size 96) # # I am the parent (490). My child's pid is 494 # # I am the child, my PID is 494 # # [490] clone3() with flags says: 0 expected 0 # ok 5 sizeof(struct clone_args) + 8 # # Running test 'exit_signal with highest 32 bits non-zero' # # [490] Trying clone3() with flags 0 (size 0) # # Invalid argument - Failed to create new process # # [490] clone3() with flags says: -22 expected -22 # ok 6 exit_signal with highest 32 bits non-zero # # Running test 'negative 32-bit exit_signal' # # [490] Trying clone3() with flags 0 (size 0) # # Invalid argument - Failed to create new process # # [490] clone3() with flags says: -22 expected -22 # ok 7 negative 32-bit exit_signal # # Running test 'exit_signal not fitting into CSIGNAL mask' # # [490] Trying clone3() with flags 0 (size 0) # # Invalid argument - Failed to create new process # # [490] clone3() with flags says: -22 expected -22 # ok 8 exit_signal not fitting into CSIGNAL mask # # Running test 'NSIG < exit_signal < CSIG' # # [490] Trying clone3() with flags 0 (size 0) # # Invalid argument - Failed to create new process # # [490] clone3() with flags says: -22 expected -22 # ok 9 NSIG < exit_signal < CSIG # # Running test 'Arguments sizeof(struct clone_args) + 8' # # [490] Trying clone3() with flags 0 (size 96) # # I am the parent (490). My child's pid is 495 # # I am the child, my PID is 495 # # [490] clone3() with flags says: 0 expected 0 # ok 10 Arguments sizeof(struct clone_args) + 8 # # Running test 'Arguments sizeof(struct clone_args) + 16' # # [490] Trying clone3() with flags 0 (size 104) # # Argument list too long - Failed to create new process # # [490] clone3() with flags says: -7 expected -7 # ok 11 Arguments sizeof(struct clone_args) + 16 # # Running test 'Arguments sizeof(struct clone_arg) * 2' # # [490] Trying clone3() with flags 0 (size 104) # # Argument list too long - Failed to create new process # # [490] clone3() with flags says: -7 expected -7 # ok 12 Arguments sizeof(struct clone_arg) * 2 # # Running test 'Arguments > page size' # # [490] Trying clone3() with flags 0 (size 4104) # # Argument list too long - Failed to create new process # # [490] clone3() with flags says: -7 expected -7 # ok 13 Arguments > page size # # Running test 'CLONE_ARGS_SIZE_VER0 in a new PID NS' # # [490] Trying clone3() with flags 0x20000000 (size 64) # # I am the parent (490). My child's pid is 496 # # I am the child, my PID is 1 # # [490] clone3() with flags says: 0 expected 0 # ok 14 CLONE_ARGS_SIZE_VER0 in a new PID NS # # Running test 'CLONE_ARGS_SIZE_VER0 - 8 in a new PID NS' # # [490] Trying clone3() with flags 0x20000000 (size 56) # # Invalid argument - Failed to create new process # # [490] clone3() with flags says: -22 expected -22 # ok 15 CLONE_ARGS_SIZE_VER0 - 8 in a new PID NS # # Running test 'sizeof(struct clone_args) + 8 in a new PID NS' # # [490] Trying clone3() with flags 0x20000000 (size 96) # # I am the parent (490). My child's pid is 497 # # I am the child, my PID is 1 # # [490] clone3() with flags says: 0 expected 0 # ok 16 sizeof(struct clone_args) + 8 in a new PID NS # # Running test 'Arguments > page size in a new PID NS' # # [490] Trying clone3() with flags 0x20000000 (size 4104) # # Argument list too long - Failed to create new process # # [490] clone3() with flags says: -7 expected -7 # ok 17 Arguments > page size in a new PID NS # # Running test 'New time NS' # # [490] Trying clone3() with flags 0x80 (size 0) # # I am the parent (490). My child's pid is 498 # # I am the child, my PID is 498 # # [490] clone3() with flags says: 0 expected 0 # ok 18 New time NS # # Running test 'exit signal (SIGCHLD) in flags' # # [490] Trying clone3() with flags 0x11 (size 0) # # Invalid argument - Failed to create new process # # [490] clone3() with flags says: -22 expected -22 # ok 19 exit signal (SIGCHLD) in flags # # Totals: pass:19 fail:0 xfail:0 xpass:0 skip:0 error:0 ok 1 selftests: clone3: clone3 # timeout set to 45 # selftests: clone3: clone3_clear_sighand # TAP version 13 # 1..1 # # clone3() syscall supported # ok 1 Cleared signal handlers for child process # # Totals: pass:1 fail:0 xfail:0 xpass:0 skip:0 error:0 ok 2 selftests: clone3: clone3_clear_sighand # timeout set to 45 # selftests: clone3: clone3_set_tid # TAP version 13 # 1..29 # # clone3() syscall supported # # /proc/sys/kernel/pid_max 4194304 # # [535] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 0 says: -22 - expected -22 # ok 1 invalid size, 0 TID with 33 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 0 says: -22 - expected -22 # ok 2 invalid size, 0 TID with 64 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 0 says: -22 - expected -22 # ok 3 invalid size, 0 TID with 65 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 0 says: -22 - expected -22 # ok 4 invalid size, 0 TID with 1344 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 0 says: -22 - expected -22 # ok 5 invalid size, 0 TID with 31 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID -1 says: -22 - expected -22 # ok 6 invalid size, TID all 1s with 33 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID -1 says: -22 - expected -22 # ok 7 invalid size, TID all 1s with 64 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID -1 says: -22 - expected -22 # ok 8 invalid size, TID all 1s with 65 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID -1 says: -22 - expected -22 # ok 9 invalid size, TID all 1s with 1344 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID -1 says: -22 - expected -22 # ok 10 invalid size, TID all 1s with 31 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 0 says: -22 - expected -22 # ok 11 valid size, 0 TID with 1 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID -1 says: -22 - expected -22 # ok 12 valid size, -1 TID with 1 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID -1 says: -22 - expected -22 # ok 13 2 TIDs, -1 and 0 with 2 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to -1 and 0x20000000 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID -1 says: -22 - expected -22 # ok 14 valid size, -1 TID with 1 TIDs and flags 0x20000000 # # [535] Trying clone3() with CLONE_SET_TID to 1 and 0x0 # # File exists - Failed to create new process # # [535] clone3() with CLONE_SET_TID 1 says: -17 - expected -17 # ok 15 duplicate PID 1 with 1 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to 1 and 0x20000000 # # I am the parent (535). My child's pid is 536 # # I am the child, my PID is 1 (expected 1) # # [535] clone3() with CLONE_SET_TID 1 says: 0 - expected 0 # ok 16 duplicate PID 1 with 1 TIDs and flags 0x20000000 # # [535] Trying clone3() with CLONE_SET_TID to 4194304 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 4194304 says: -22 - expected -22 # ok 17 set TID to maximum with 1 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to 4194304 and 0x20000000 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 4194304 says: -22 - expected -22 # ok 18 set TID to maximum with 1 TIDs and flags 0x20000000 # # Child has PID 537 # # [535] Trying clone3() with CLONE_SET_TID to 537 and 0x0 # # I am the parent (535). My child's pid is 537 # # I am the child, my PID is 537 (expected 537) # # [535] clone3() with CLONE_SET_TID 537 says: 0 - expected 0 # ok 19 reallocate child TID with 1 TIDs and flags 0x0 # # [535] Trying clone3() with CLONE_SET_TID to 537 and 0x20000000 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 537 says: -22 - expected -22 # ok 20 duplicate child TID with 1 TIDs and flags 0x20000000 # # [535] Trying clone3() with CLONE_SET_TID to 1 and 0x20000000 # # I am the parent (535). My child's pid is 537 # # I am the child, my PID is 1 (expected 1) # # [535] clone3() with CLONE_SET_TID 1 says: 0 - expected 0 # ok 21 create PID 1 in new NS with 2 TIDs and flags 0x20000000 # # unshare PID namespace # # [535] Trying clone3() with CLONE_SET_TID to 537 and 0x0 # # Invalid argument - Failed to create new process # # [535] clone3() with CLONE_SET_TID 537 says: -22 - expected -22 # ok 22 duplicate PID 1 with 1 TIDs and flags 0x0 # # [1] Trying clone3() with CLONE_SET_TID to 43 and 0x0 # # Invalid argument - Failed to create new process # # [1] clone3() with CLONE_SET_TID 43 says: -22 - expected -22 # ok 23 check leak on invalid TID -1 with 2 TIDs and flags 0x0 # # [1] Trying clone3() with CLONE_SET_TID to 43 and 0x0 # # I am the parent (1). My child's pid is 43 # # I am the child, my PID is 43 (expected 43) # # [1] clone3() with CLONE_SET_TID 43 says: 0 - expected 0 # ok 24 check leak on invalid specific TID with 2 TIDs and flags 0x0 # # Child in PID namespace has PID 1 # # [1] Trying clone3() with CLONE_SET_TID to 2 and 0x0 # # I am the parent (1). My child's pid is 2 # # I am the child, my PID is 2 (expected 2) # # [1] clone3() with CLONE_SET_TID 2 says: 0 - expected 0 # ok 25 create PID 2 in child NS with 1 TIDs and flags 0x0 # # [1] Trying clone3() with CLONE_SET_TID to 1 and 0x20000000 # # Invalid argument - Failed to create new process # # [1] clone3() with CLONE_SET_TID 1 says: -22 - expected -22 # ok 26 fail due to invalid TID at level 1 with 3 TIDs and flags 0x20000000 # # [1] Trying clone3() with CLONE_SET_TID to 1 and 0x20000000 # # Invalid argument - Failed to create new process # # [1] clone3() with CLONE_SET_TID 1 says: -22 - expected -22 # ok 27 fail due to too few active PID NSs with 4 TIDs and flags 0x20000000 # # [1] Trying clone3() with CLONE_SET_TID to 1 and 0x20000000 # # I am the parent (1). My child's pid is 42 # # I am the child, my PID is 1 (expected 1) # # [1] Child is ready and waiting # # [535] Child is ready and waiting # # [1] clone3() with CLONE_SET_TID 1 says: 0 - expected 0 # ok 28 verify that we have 3 PID NSs with 3 TIDs and flags 0x20000000 # # Expecting PIDs 537, 42, 1 # # Have PIDs in namespaces: 537, 42, 1 # ok 29 PIDs in all namespaces as expected # # Totals: pass:29 fail:0 xfail:0 xpass:0 skip:0 error:0 ok 3 selftests: clone3: clone3_set_tid # timeout set to 45 # selftests: clone3: clone3_cap_checkpoint_restore # TAP version 13 # 1..1 # # Starting 1 tests from 1 test cases. # # RUN global.clone3_cap_checkpoint_restore ... # # clone3() syscall supported # # clone3_cap_checkpoint_restore.c:151:clone3_cap_checkpoint_restore:Child has PID 559 # cap_set_proc: Operation not permitted # # clone3_cap_checkpoint_restore.c:160:clone3_cap_checkpoint_restore:Expected set_capability() (-1) == 0 (0) # # clone3_cap_checkpoint_restore.c:161:clone3_cap_checkpoint_restore:Could not set CAP_CHECKPOINT_RESTORE # # clone3_cap_checkpoint_restore: Test terminated by assertion # # FAIL global.clone3_cap_checkpoint_restore # not ok 1 global.clone3_cap_checkpoint_restore # # FAILED: 0 / 1 tests passed. # # Totals: pass:0 fail:1 xfail:0 xpass:0 skip:0 error:0 not ok 4 selftests: clone3: clone3_cap_checkpoint_restore # exit=1 clone3_clone3_simple_clone3 pass clone3_clone3_clone3_in_a_new_PID_NS pass clone3_clone3_CLONE_ARGS_SIZE_VER0 pass clone3_clone3_CLONE_ARGS_SIZE_VER0__8 pass clone3_clone3_sizeof_struct_clone_args_8 pass clone3_clone3_exit_signal_with_highest_32_bits_non-zero pass clone3_clone3_negative_32-bit_exit_signal pass clone3_clone3_exit_signal_not_fitting_into_CSIGNAL_mask pass clone3_clone3_NSIG_exit_signal_CSIG pass clone3_clone3_Arguments_sizeof_struct_clone_args_8 pass clone3_clone3_Arguments_sizeof_struct_clone_args_16 pass clone3_clone3_Arguments_sizeof_struct_clone_arg_2 pass clone3_clone3_Arguments_page_size pass clone3_clone3_CLONE_ARGS_SIZE_VER0_in_a_new_PID_NS pass clone3_clone3_CLONE_ARGS_SIZE_VER0__8_in_a_new_PID_NS pass clone3_clone3_sizeof_struct_clone_args_8_in_a_new_PID_NS pass clone3_clone3_Arguments_page_size_in_a_new_PID_NS pass clone3_clone3_New_time_NS pass clone3_clone3_exit_signal_SIGCHLD_in_flags pass clone3_clone3 pass clone3_clone3_clear_sighand_Cleared_signal_handlers_for_child_process pass clone3_clone3_clear_sighand pass clone3_clone3_set_tid_invalid_size_0_TID_with_33_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_0_TID_with_64_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_0_TID_with_65_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_0_TID_with_1344_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_0_TID_with_31_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_TID_all_1s_with_33_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_TID_all_1s_with_64_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_TID_all_1s_with_65_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_TID_all_1s_with_1344_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_invalid_size_TID_all_1s_with_31_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_valid_size_0_TID_with_1_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_valid_size_1_TID_with_1_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_2_TIDs_1_and_0_with_2_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_valid_size_1_TID_with_1_TIDs_and_flags_0x20000000 pass clone3_clone3_set_tid_duplicate_PID_1_with_1_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_duplicate_PID_1_with_1_TIDs_and_flags_0x20000000 pass clone3_clone3_set_tid_set_TID_to_maximum_with_1_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_set_TID_to_maximum_with_1_TIDs_and_flags_0x20000000 pass clone3_clone3_set_tid_reallocate_child_TID_with_1_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_duplicate_child_TID_with_1_TIDs_and_flags_0x20000000 pass clone3_clone3_set_tid_create_PID_1_in_new_NS_with_2_TIDs_and_flags_0x20000000 pass clone3_clone3_set_tid_duplicate_PID_1_with_1_TIDs_and_flags_0x0_dup2 pass clone3_clone3_set_tid_check_leak_on_invalid_TID_1_with_2_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_check_leak_on_invalid_specific_TID_with_2_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_create_PID_2_in_child_NS_with_1_TIDs_and_flags_0x0 pass clone3_clone3_set_tid_fail_due_to_invalid_TID_at_level_1_with_3_TIDs_and_flags_0x20000000 pass clone3_clone3_set_tid_fail_due_to_too_few_active_PID_NSs_with_4_TIDs_and_flags_0x20000000 pass clone3_clone3_set_tid_verify_that_we_have_3_PID_NSs_with_3_TIDs_and_flags_0x20000000 pass clone3_clone3_set_tid_PIDs_in_all_namespaces_as_expected pass clone3_clone3_set_tid pass clone3_clone3_cap_checkpoint_restore_global_clone3_cap_checkpoint_restore fail clone3_clone3_cap_checkpoint_restore fail + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #