Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.116 (255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 511420/tftp-deploy-jq1c5bh1/kernel/Image tftp 0x82000000 511420/tftp-deploy-jq1c5bh1/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.116; sending through gateway 172.16.0.254 Filename '511420/tftp-deploy-jq1c5bh1/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###### 14.6 MiB/s done Bytes transferred = 47784448 (2d92200 hex) => tftp 0x90080000 511420/tftp-deploy-jq1c5bh1/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 511420/tftp-deploy-jq1c5bh1/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.116; sending through gateway 172.16.0.254 Filename '511420/tftp-deploy-jq1c5bh1/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################ 17.1 MiB/s done Bytes transferred = 26160221 (18f2c5d hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 511420/tftp-deploy-jq1c5bh1/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 511420/tftp-deploy-jq1c5bh1/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.116; sending through gateway 172.16.0.254 Filename '511420/tftp-deploy-jq1c5bh1/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *### 7.1 MiB/s done Bytes transferred = 29861 (74a5 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-05 8:21:55 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 26160157 Bytes = 24.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a4a4 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.12.0-rc6-next-20241105 (KernelCI@build-j363025-arm64-gcc-12-defconfig-config-arm64-64k-pagenzwrk) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Tue Nov 5 07:58:07 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550a0] enabled [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x20fff453c0-0x20fff47dff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 1056 pages in unavailable ranges [ 0.000000] cma: Reserved 512 MiB at 0x00000000c0000000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 2 pages/cpu s61848 r8192 d61032 u131072 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 6, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 5, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64480 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f7d30000-0x00000000fbd30000] (64MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080180000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080160000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080170000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008897] Console: colour dummy device 80x25 <6>[ 0.013736] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024457] pid_max: default: 32768 minimum: 301 <6>[ 0.029424] LSM: initializing lsm=capability <6>[ 0.034086] Mount-cache hash table entries: 8192 (order: 0, 65536 bytes, linear) <6>[ 0.041833] Mountpoint-cache hash table entries: 8192 (order: 0, 65536 bytes, linear) <6>[ 0.062457] rcu: Hierarchical SRCU implementation. <6>[ 0.067573] rcu: Max phase no-delay instances is 1000. <6>[ 0.073274] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.081839] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.088781] EFI services will not be available. <6>[ 0.093768] smp: Bringing up secondary CPUs ... <6>[ 0.098912] Detected PIPT I-cache on CPU1 <6>[ 0.098954] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.098964] GICv3: CPU1: using allocated LPI pending table @0x0000002080200000 <6>[ 0.098990] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.099100] smp: Brought up 1 node, 2 CPUs <6>[ 0.129421] SMP: Total of 2 processors activated. <6>[ 0.134435] CPU: All CPU(s) started at EL2 <6>[ 0.138855] CPU features: detected: 32-bit EL0 Support <6>[ 0.144308] CPU features: detected: 32-bit EL1 Support <6>[ 0.149767] CPU features: detected: CRC32 instructions <6>[ 0.155243] alternatives: applying system-wide alternatives <6>[ 0.162008] Memory: 3440896K/4126720K available (17344K kernel code, 5128K rwdata, 12352K rodata, 11264K init, 1122K bss, 151808K reserved, 524288K cma-reserved) <6>[ 0.177388] devtmpfs: initialized <6>[ 0.184026] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.194154] futex hash table entries: 512 (order: -1, 32768 bytes, linear) <6>[ 0.201839] 1294 pages in range for non-PLT usage <6>[ 0.201844] 32014 pages in range for PLT usage <6>[ 0.206977] pinctrl core: initialized pinctrl subsystem <6>[ 0.217738] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.225385] SoC family: QorIQ LS1028A <6>[ 0.229339] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.234697] DMI not present or invalid. <6>[ 0.240447] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.249667] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.257190] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.265387] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.273689] audit: initializing netlink subsys (disabled) <5>[ 0.279720] audit: type=2000 audit(0.168:1): state=initialized audit_enabled=0 res=1 <6>[ 0.280453] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.287818] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.294189] cpuidle: using governor menu <6>[ 0.305445] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.312597] ASID allocator initialised with 65536 entries <6>[ 0.319662] Serial: AMBA PL011 UART driver <6>[ 0.337896] HugeTLB: registered 16.0 GiB page size, pre-allocated 0 pages <6>[ 0.345030] HugeTLB: 0 KiB vmemmap can be freed for a 16.0 GiB page <6>[ 0.351623] HugeTLB: registered 512 MiB page size, pre-allocated 0 pages <6>[ 0.358652] HugeTLB: 0 KiB vmemmap can be freed for a 512 MiB page <6>[ 0.365155] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.372271] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.380374] ACPI: Interpreter disabled. <6>[ 0.386111] iommu: Default domain type: Translated <6>[ 0.391218] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.397882] SCSI subsystem initialized <6>[ 0.402152] usbcore: registered new interface driver usbfs <6>[ 0.407977] usbcore: registered new interface driver hub <6>[ 0.413623] usbcore: registered new device driver usb <6>[ 0.419549] i2c i2c-0: IMX I2C adapter registered <6>[ 0.424792] i2c i2c-1: IMX I2C adapter registered <6>[ 0.430159] i2c i2c-2: IMX I2C adapter registered <6>[ 0.435696] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.440988] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.450497] PTP clock support registered <6>[ 0.454796] EDAC MC: Ver: 3.0.0 <6>[ 0.458492] scmi_core: SCMI protocol bus registered <6>[ 0.464299] FPGA manager framework <6>[ 0.468051] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.475004] vgaarb: loaded <6>[ 0.478249] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.484961] VFS: Disk quotas dquot_6.6.0 <6>[ 0.489220] VFS: Dquot-cache hash table entries: 8192 (order 0, 65536 bytes) <6>[ 0.496768] pnp: PnP ACPI: disabled <6>[ 0.504966] NET: Registered PF_INET protocol family <6>[ 0.510338] IP idents hash table entries: 65536 (order: 3, 524288 bytes, linear) <6>[ 0.520084] tcp_listen_portaddr_hash hash table entries: 4096 (order: 0, 65536 bytes, linear) <6>[ 0.529032] Table-perturb hash table entries: 65536 (order: 2, 262144 bytes, linear) <6>[ 0.537126] TCP established hash table entries: 32768 (order: 2, 262144 bytes, linear) <6>[ 0.545469] TCP bind hash table entries: 32768 (order: 4, 1048576 bytes, linear) <6>[ 0.553820] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.560768] UDP hash table entries: 2048 (order: 0, 65536 bytes, linear) <6>[ 0.567838] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes, linear) <6>[ 0.575421] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.581714] RPC: Registered named UNIX socket transport module. <6>[ 0.587968] RPC: Registered udp transport module. <6>[ 0.592982] RPC: Registered tcp transport module. <6>[ 0.597993] RPC: Registered tcp-with-tls transport module. <6>[ 0.603795] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.610568] PCI: CLS 0 bytes, default 64 <6>[ 0.614945] Unpacking initramfs... <6>[ 0.617120] kvm [1]: nv: 557 coarse grained trap handlers <6>[ 0.624748] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.629606] kvm [1]: GICv3: no GICV resource entry <6>[ 0.634732] kvm [1]: disabling GICv2 emulation <6>[ 0.639502] kvm [1]: GIC system register CPU interface enabled <6>[ 0.645671] kvm [1]: vgic interrupt IRQ9 <6>[ 0.649912] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 0.656524] Initialise system trusted keyrings <6>[ 0.661468] workingset: timestamp_bits=42 max_order=16 bucket_order=0 <6>[ 0.668481] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.678894] NFS: Registering the id_resolver key type <5>[ 0.684319] Key type id_resolver registered <5>[ 0.688831] Key type id_legacy registered <6>[ 0.693178] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.700217] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.708088] 9p: Installing v9fs 9p2000 file system support <5>[ 0.742664] Key type asymmetric registered <5>[ 0.747079] Asymmetric key parser 'x509' registered <6>[ 0.752320] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.760061] io scheduler mq-deadline registered <6>[ 0.764901] io scheduler kyber registered <6>[ 0.769260] io scheduler bfq registered <6>[ 0.780926] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 0.787864] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.796042] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.805218] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.814392] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.823570] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.832746] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.841919] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.851099] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.860318] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.869577] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.876907] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.882465] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.889869] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.897722] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.905135] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.912986] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.920389] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.928233] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.935674] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 0.945398] pci 0000:00:00.0: BAR 0 [mem 0x1f8000000-0x1f803ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 0.956063] pci 0000:00:00.0: BAR 2 [mem 0x1f8160000-0x1f816ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 0.967158] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81d0000-0x1f81dffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 0.978085] pci 0000:00:00.0: VF BAR 4 [mem 0x1f81f0000-0x1f81fffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 0.989470] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.995301] pci 0000:00:00.0: VF BAR 0 [mem 0x1f81d0000-0x1f81effff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.004816] pci 0000:00:00.0: VF BAR 2 [mem 0x1f81f0000-0x1f820ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.014974] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.024698] pci 0000:00:00.1: BAR 0 [mem 0x1f8040000-0x1f807ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.035364] pci 0000:00:00.1: BAR 2 [mem 0x1f8170000-0x1f817ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.046463] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8210000-0x1f821ffff 64bit]: from Enhanced Allocation, properties 0x4 <6>[ 1.057382] pci 0000:00:00.1: VF BAR 4 [mem 0x1f8230000-0x1f823ffff 64bit pref]: from Enhanced Allocation, properties 0x3 <6>[ 1.068755] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.074581] pci 0000:00:00.1: VF BAR 0 [mem 0x1f8210000-0x1f822ffff 64bit]: contains BAR 0 for 2 VFs <6>[ 1.084091] pci 0000:00:00.1: VF BAR 2 [mem 0x1f8230000-0x1f824ffff 64bit pref]: contains BAR 2 for 2 VFs <6>[ 1.094231] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.103947] pci 0000:00:00.2: BAR 0 [mem 0x1f8080000-0x1f80bffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.114585] pci 0000:00:00.2: BAR 2 [mem 0x1f8180000-0x1f818ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.125670] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.131677] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.141389] pci 0000:00:00.3: BAR 0 [mem 0x1f8100000-0x1f811ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.152033] pci 0000:00:00.3: BAR 2 [mem 0x1f8190000-0x1f819ffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.163132] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.169113] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 PCIe Root Complex Integrated Endpoint <6>[ 1.178815] pci 0000:00:00.4: BAR 0 [mem 0x1f8120000-0x1f813ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.189455] pci 0000:00:00.4: BAR 2 [mem 0x1f81a0000-0x1f81affff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.200546] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.206624] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 PCIe Root Complex Integrated Endpoint <6>[ 1.216333] pci 0000:00:00.5: BAR 0 [mem 0x1f8140000-0x1f815ffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.226983] pci 0000:00:00.5: BAR 2 [mem 0x1f81b0000-0x1f81bffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.238060] pci 0000:00:00.5: BAR 4 [mem 0x1fc000000-0x1fc3fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.248709] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.254744] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 PCIe Root Complex Integrated Endpoint <6>[ 1.264448] pci 0000:00:00.6: BAR 0 [mem 0x1f80c0000-0x1f80fffff 64bit]: from Enhanced Allocation, properties 0x0 <6>[ 1.275088] pci 0000:00:00.6: BAR 2 [mem 0x1f81c0000-0x1f81cffff 64bit pref]: from Enhanced Allocation, properties 0x1 <6>[ 1.286180] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.292964] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 PCIe Root Complex Event Collector <6>[ 1.302339] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.310314] pci_bus 0000:00: resource 4 [mem 0x1f8000000-0x1f815ffff] <6>[ 1.317095] pci_bus 0000:00: resource 5 [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.324332] pci_bus 0000:00: resource 6 [mem 0x1f81d0000-0x1f81effff] <6>[ 1.331121] pci_bus 0000:00: resource 7 [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.338346] pci_bus 0000:00: resource 8 [mem 0x1f8210000-0x1f822ffff] <6>[ 1.345131] pci_bus 0000:00: resource 9 [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.352366] pci_bus 0000:00: resource 10 [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.462292] pci 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 1.470045] pci 0000:00:00.1: enetc_fixup_clear_rss_rfs+0x0/0x5c took 108170 usecs <6>[ 1.492292] Freeing initrd memory: 25472K <6>[ 1.578264] pci 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 1.584874] pci 0000:00:00.2: enetc_fixup_clear_rss_rfs+0x0/0x5c took 104361 usecs <6>[ 1.694265] pci 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 1.700845] pci 0000:00:00.6: enetc_fixup_clear_rss_rfs+0x0/0x5c took 105480 usecs <6>[ 1.708791] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.716949] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.723234] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.729828] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.737505] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.746393] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.755328] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 2.722259] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.728664] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.735701] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.741506] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.748013] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.758926] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 2.766590] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.772178] pci 0001:00:00.0: supports D1 D2 <6>[ 2.776754] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.784043] pci 0001:00:00.0: PCI bridge to [bus 01-ff] <6>[ 2.789593] pci_bus 0001:00: resource 4 [io 0x0000-0xffff] <6>[ 2.795486] pci_bus 0001:00: resource 5 [mem 0x8040000000-0x807fffffff] <6>[ 2.802526] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.810198] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.819090] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.828007] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.794258] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.800652] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.807688] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.813493] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.822807] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.833715] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 PCIe Root Port <6>[ 3.841379] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.846963] pci 0002:00:00.0: supports D1 D2 <6>[ 3.851539] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.858831] pci 0002:00:00.0: PCI bridge to [bus 01-ff] <6>[ 3.864379] pci_bus 0002:00: resource 4 [io 0x10000-0x1ffff] <6>[ 3.870446] pci_bus 0002:00: resource 5 [mem 0x8840000000-0x887fffffff] <6>[ 3.896883] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.905294] printk: legacy console [ttyS0] disabled <6>[ 3.910663] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.919834] printk: legacy console [ttyS0] enabled <6>[ 3.919834] printk: legacy console [ttyS0] enabled <6>[ 3.930026] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.930026] printk: legacy bootconsole [ns16550a0] disabled <6>[ 3.946806] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.956765] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 3.966780] msm_serial: driver initialized <6>[ 3.971377] SuperH (H)SCI(F) driver initialized <6>[ 3.976298] STM32 USART driver initialized <5>[ 3.984118] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.990884] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.995783] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.001381] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.006981] arm-smmu 5000000.iommu: nested translation <5>[ 4.012488] arm-smmu 5000000.iommu: coherent table walk <5>[ 4.018086] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 4.025690] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.033121] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.039946] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.046679] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.053407] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.060345] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 4.066520] arm-smmu 5000000.iommu: Failed to disable prefetcher for errata workarounds, check SACR.CACHE_LOCK <6>[ 4.080136] loop: module loaded <6>[ 4.091656] megasas: 07.727.03.00-rc1 <5>[ 4.130294] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.137402] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.142913] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.148631] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.155642] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.162668] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.168878] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.179037] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.185066] thunder_xcv, ver 1.0 <6>[ 4.188601] thunder_bgx, ver 1.0 <6>[ 4.192125] nicpf, ver 1.0 <6>[ 4.195868] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 0 <6>[ 4.306266] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.313718] fsl_enetc_mdio 0000:00:00.3: Enabled ERR050089 workaround <6>[ 4.338306] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 1 <6>[ 4.344623] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.351617] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.360646] pps pps0: new PPS source ptp0 <6>[ 4.365439] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.372967] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.378608] hclge is initializing <6>[ 4.382204] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.387381] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.393435] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.398682] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.404910] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.410592] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.416465] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.423020] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.429464] sky2: driver version 1.30 <6>[ 4.434415] VFIO - User Level meta-driver version: 0.3 <6>[ 4.440152] dwc3 3100000.usb: Adding to iommu group 2 <6>[ 4.446608] dwc3 3110000.usb: Adding to iommu group 3 <6>[ 4.455273] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.461064] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.469230] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.478942] xhci-hcd xhci-hcd.0.auto: irq 98, io mem 0x03100000 <6>[ 4.485224] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.491007] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.498994] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.506207] hub 1-0:1.0: USB hub found <6>[ 4.510324] hub 1-0:1.0: 1 port detected <6>[ 4.514719] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.523390] hub 2-0:1.0: USB hub found <6>[ 4.527434] hub 2-0:1.0: 1 port detected <6>[ 4.531855] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.537638] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.545812] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.555538] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03110000 <6>[ 4.561819] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.567598] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.575574] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.582718] hub 3-0:1.0: USB hub found <6>[ 4.586765] hub 3-0:1.0: 1 port detected <6>[ 4.591158] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.599854] hub 4-0:1.0: USB hub found <6>[ 4.603897] hub 4-0:1.0: 1 port detected <6>[ 4.608654] usbcore: registered new interface driver usb-storage <6>[ 4.617116] i2c_dev: i2c /dev entries driver <6>[ 4.625429] sp805-wdt c000000.watchdog: registration successful <6>[ 4.631823] sp805-wdt c010000.watchdog: registration successful <6>[ 4.640193] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.649082] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.655595] sdhci: Copyright(c) Pierre Ossman <6>[ 4.660799] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.667783] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.674341] sdhci-esdhc 2150000.mmc: Adding to iommu group 4 <6>[ 4.680706] sdhci-esdhc 2140000.mmc: Adding to iommu group 5 <6>[ 4.681213] usbcore: registered new interface driver usbhid <6>[ 4.692577] usbhid: USB HID core driver <6>[ 4.702417] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 (0,8000003f) counters available <6>[ 4.716150] NET: Registered PF_PACKET protocol family <6>[ 4.721593] 9pnet: Installing 9P2000 support <6>[ 4.726165] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.726318] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <5>[ 4.733424] Key type dns_resolver registered <6>[ 4.751284] registered taskstats version 1 <5>[ 4.755808] Loading compiled-in X.509 certificates <6>[ 4.766419] Demotion targets for Node 0: null <6>[ 4.773573] fsl-edma 22c0000.dma-controller: Adding to iommu group 6 <6>[ 4.781403] pcieport 0001:00:00.0: Adding to iommu group 7 <6>[ 4.787441] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.793805] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <3>[ 4.799884] genirq: Flags mismatch irq 104. 00002084 (PCIe bwctrl) vs. 00200084 (PCIe PME) <3>[ 4.808538] pcie_bwctrl 0001:00:00.0:pcie010: probe with driver pcie_bwctrl failed with error -16 <6>[ 4.817875] pcieport 0002:00:00.0: Adding to iommu group 8 <6>[ 4.823885] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.830180] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <3>[ 4.836287] genirq: Flags mismatch irq 105. 00002084 (PCIe bwctrl) vs. 00200084 (PCIe PME) <6>[ 4.844967] usb 3-1: new high-speed USB device number 2 using xhci-hcd <3>[ 4.846279] pcie_bwctrl 0002:00:00.0:pcie010: probe with driver pcie_bwctrl failed with error -16 <6>[ 4.863810] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 4.889357] mmc0: new HS400 MMC card at address 0001 <6>[ 4.895120] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.901458] mmcblk0: p1 p2 <6>[ 4.904955] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.911161] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.917218] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 5.030854] hub 3-1:1.0: USB hub found <6>[ 5.035081] hub 3-1:1.0: 7 ports detected <6>[ 17.166442] clk: Disabling unused clocks <6>[ 17.170811] PM: genpd: Disabling unused power domains <6>[ 17.176213] ALSA device list: <6>[ 17.179498] No soundcards found. <6>[ 17.189136] Freeing unused kernel memory: 11264K <6>[ 17.194207] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 17.255017] udevd[109]: starting version 3.2.9 <5>[ 18.406266] random: crng init done <27>[ 18.412988] udevd[109]: specified user 'tss' unknown <27>[ 18.418392] udevd[109]: specified group 'tss' unknown <30>[ 18.424872] udevd[110]: starting eudev-3.2.9 <6>[ 18.698318] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 18.722455] fsl_ddr_edac acquired irq 108 for MC <6>[ 18.733855] NET: Registered PF_INET6 protocol family <4>[ 18.746720] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 18.756563] fsl_ddr_edac MC err registered <4>[ 18.768179] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 18.774995] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 18.778537] Segment Routing with IPv6 <6>[ 18.790281] wm8904 2-001a: revision A <4>[ 18.792484] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 18.808045] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 18.820773] In-situ OAM (IOAM) with IPv6 <6>[ 18.823410] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <6>[ 18.836344] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 18.842093] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 18.856210] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 18.863161] rtc-rv8803 0-0032: registered as rtc0 <6>[ 18.871308] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.879770] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 18.889007] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 18.898089] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 18.919089] CAN device driver interface <6>[ 18.927677] input: buttons1 as /devices/platform/buttons1/input/input12 <6>[ 18.966737] ftm-alarm 2800000.rtc: registered as rtc1 <6>[ 19.001385] caam 8000000.crypto: Entropy delay = 3200 <6>[ 19.007405] usbcore: registered new device driver onboard-usb-dev <6>[ 19.077456] caam 8000000.crypto: Instantiated RNG4 SH0 <4>[ 19.112634] sysfs: cannot create duplicate filename '/devices/platform/sound/sai-tx-rx-wm8904-hifi' <6>[ 19.134317] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 19.146285] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 19.158281] caam 8000000.crypto: job rings = 4, qi = 0 <4>[ 19.171796] CPU: 0 UID: 0 PID: 120 Comm: udevd Not tainted 6.12.0-rc6-next-20241105 #1 <4>[ 19.180022] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT) <4>[ 19.188577] Call trace: <4>[ 19.191287] show_stack+0x18/0x24 (C) <4>[ 19.195233] dump_stack_lvl+0x78/0x90 <4>[ 19.199172] dump_stack+0x18/0x24 <4>[ 19.202760] sysfs_warn_dup+0x64/0x80 <4>[ 19.206697] sysfs_create_dir_ns+0xec/0x10c <4>[ 19.211157] kobject_add_internal+0x98/0x26c <4>[ 19.215703] kobject_add+0x9c/0x10c <4>[ 19.219464] device_add+0xc0/0x790 <4>[ 19.223139] device_register+0x20/0x30 <4>[ 19.227163] snd_soc_add_pcm_runtimes+0x328/0x850 <4>[ 19.232145] snd_soc_bind_card+0x2b4/0xb50 <4>[ 19.236515] snd_soc_register_card+0xf0/0x108 <4>[ 19.241147] devm_snd_soc_register_card+0x4c/0xa4 <4>[ 19.246128] simple_probe+0x21c/0x3e8 [snd_soc_simple_card] <4>[ 19.251989] platform_probe+0x68/0xc4 <4>[ 19.255925] really_probe+0xbc/0x298 <4>[ 19.259771] __driver_probe_device+0x78/0x12c <4>[ 19.264403] driver_probe_device+0xd8/0x15c <4>[ 19.268860] __driver_attach+0x94/0x19c <4>[ 19.272969] bus_for_each_dev+0x78/0xd4 <4>[ 19.277077] driver_attach+0x24/0x30 <4>[ 19.280923] bus_add_driver+0xe4/0x208 <4>[ 19.284944] driver_register+0x60/0x128 <4>[ 19.289053] __platform_driver_register+0x24/0x30 <4>[ 19.294034] simple_card_init+0x20/0x10000 [snd_soc_simple_card] <4>[ 19.300324] do_one_initcall+0x80/0x1c4 <4>[ 19.304433] do_init_module+0x60/0x1f0 <4>[ 19.308454] load_module+0x1a98/0x1b2c <4>[ 19.312476] init_module_from_file+0x84/0xc4 <4>[ 19.317020] __arm64_sys_finit_module+0x144/0x328 <4>[ 19.322001] invoke_syscall.constprop.0+0x50/0xe4 <4>[ 19.326984] do_el0_svc+0x40/0xc8 <4>[ 19.330571] el0_svc+0x40/0x14c <4>[ 19.333982] el0t_64_sync_handler+0x10c/0x138 <4>[ 19.338613] el0t_64_sync+0x198/0x19c <3>[ 19.346088] kobject: kobject_add_internal failed for sai-tx-rx-wm8904-hifi with -EEXIST, don't try to register things with the same name in the same directory. <3>[ 19.362483] asoc-simple-card sound: probe with driver asoc-simple-card failed with error -12 <6>[ 19.374993] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 19.386620] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 19.393806] mali-dp f080000.display: Adding to iommu group 9 <6>[ 19.400292] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 <6>[ 19.423493] caam_jr 8010000.jr: Adding to iommu group 10 <6>[ 19.442373] caam algorithms registered in /proc/crypto <6>[ 19.447872] caam 8000000.crypto: registering rng-caam <6>[ 19.453375] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 19.460561] caam_jr 8020000.jr: Adding to iommu group 11 <6>[ 19.466861] caam_jr 8030000.jr: Adding to iommu group 12 <6>[ 19.473092] caam_jr 8040000.jr: Adding to iommu group 13 done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-511420/environment . /lava-511420/environment / # /lava-511420/bin/lava-test-runner /lava-511420/0 /lava-511420/bin/lava-test-runner /lava-511420/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 20.075022] d /lava-511420/0/tests/0_dmesg + cat uuid + UUID=511420_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 20.097077] <8>[ 20.119830] <8>[ 20.143071] + set +x <8>[ 20.152445] / #