Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'.  U-Boot SPL 2018.01-dirty (Jul 31 2024 - 16:15:46) Trying to boot from MMC2 U-Boot 2018.01-dirty (Jul 31 2024 - 16:15:46 +0200) CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 4 seconds U-Boot> setenv autoload no setenv autoload no U-Boot> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff U-Boot> dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.175.42 (9 ms) U-Boot> setenv serverip 192.168.32.2 setenv serverip 192.168.32.2 U-Boot> tftp 0x82000000 1221392/tftp-deploy-hypb1ltf/kernel/zImage tftp 0x82000000 1221392/tftp-deploy-hypb1ltf/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1221392/tftp-deploy-hypb1ltf/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################## 3.1 MiB/s done Bytes transferred = 5433648 (52e930 hex) U-Boot> tftp 0x83000000 1221392/tftp-deploy-hypb1ltf/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1221392/tftp-deploy-hypb1ltf/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1221392/tftp-deploy-hypb1ltf/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################ 3.3 MiB/s done Bytes transferred = 15729131 (f001eb hex) U-Boot> setenv initrd_size ${filesize} setenv initrd_size ${filesize} U-Boot> tftp 0x88000000 1221392/tftp-deploy-hypb1ltf/dtb/am335x-boneblack.dtb tftp 0x88000000 1221392/tftp-deploy-hypb1ltf/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1221392/tftp-deploy-hypb1ltf/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 2.4 MiB/s done Bytes transferred = 70544 (11390 hex) U-Boot> setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-11-11 10:04:28 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15729067 Bytes = 15 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801438f Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc7-next-20241111 (KernelCI@build-j372524-arm-gcc-12-omap2plus-defconfig-v2krf) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Mon Nov 11 09:55:33 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: legacy bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 17 pages/cpu s39820 r8192 d21620 u69632 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] printk: log buffer data + meta data: 65536 + 204800 = 270336 bytes <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130560 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1. <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000003] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008344] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018639] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030325] Console: colour dummy device 80x30 <3>[ 0.035229] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042325] This ensures that you still see kernel messages. Please <3>[ 0.049062] update your kernel commandline. <6>[ 0.053671] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095663] CPU: Testing write buffer coherency: ok <6>[ 0.101049] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106520] pid_max: default: 32768 minimum: 301 <6>[ 0.111675] LSM: initializing lsm=capability <6>[ 0.116510] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124355] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134213] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.209241] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.216561] rcu: Hierarchical SRCU implementation. <6>[ 0.221820] rcu: Max phase no-delay instances is 1000. <6>[ 0.228556] smp: Bringing up secondary CPUs ... <6>[ 0.233606] smp: Brought up 1 node, 1 CPU <6>[ 0.238008] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.244772] CPU: All CPU(s) started in SVC mode. <6>[ 0.249984] Memory: 466620K/522240K available (11264K kernel code, 1159K rwdata, 2732K rodata, 1024K init, 291K bss, 37608K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.266449] devtmpfs: initialized <6>[ 0.285020] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.293666] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.304149] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.312803] pinctrl core: initialized pinctrl subsystem <6>[ 0.321033] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.330320] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.338229] audit: initializing netlink subsys (disabled) <6>[ 0.345447] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.345472] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.352107] thermal_sys: Registered thermal governor 'user_space' <5>[ 0.358684] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 <6>[ 0.373577] cpuidle: using governor menu <6>[ 0.399202] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 0.418024] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <6>[ 0.437943] No ATAGs? <6>[ 0.440660] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.449711] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. <6>[ 0.482202] iommu: Default domain type: Translated <6>[ 0.487429] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.509735] SCSI subsystem initialized <6>[ 0.519631] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.525019] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.534767] PTP clock support registered <6>[ 0.569169] vgaarb: loaded <6>[ 0.572618] clocksource: Switched to clocksource dmtimer <5>[ 0.579160] VFS: Disk quotas dquot_6.6.0 <6>[ 0.583567] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 0.637736] NET: Registered PF_INET protocol family <6>[ 0.643494] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.652567] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.661523] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.669800] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.678110] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 0.685841] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.692789] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.699805] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.707450] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.784811] RPC: Registered named UNIX socket transport module. <6>[ 0.791207] RPC: Registered udp transport module. <6>[ 0.796383] RPC: Registered tcp transport module. <6>[ 0.801494] RPC: Registered tcp-with-tls transport module. <6>[ 0.807430] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.814368] PCI: CLS 0 bytes, default 64 <5>[ 0.820085] Initialise system trusted keyrings <6>[ 0.836934] Trying to unpack rootfs image as initramfs... <6>[ 0.912997] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 0.921403] NFS: Registering the id_resolver key type <5>[ 0.927116] Key type id_resolver registered <5>[ 0.931697] Key type id_legacy registered <6>[ 0.936187] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 1.013312] Key type asymmetric registered <5>[ 1.017851] Asymmetric key parser 'x509' registered <6>[ 1.023337] io scheduler mq-deadline registered <6>[ 1.028277] io scheduler kyber registered <6>[ 1.032792] io scheduler bfq registered <6>[ 1.092826] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.113033] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 1.194034] brd: module loaded <6>[ 1.229169] loop: module loaded <3>[ 1.233688] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 1.267264] i2c_dev: i2c /dev entries driver <5>[ 1.272980] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 1.280596] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.287307] sdhci: Copyright(c) Pierre Ossman <6>[ 1.292246] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.299395] Initializing XFRM netlink socket <6>[ 1.304303] NET: Registered PF_INET6 protocol family <6>[ 1.404515] Segment Routing with IPv6 <6>[ 1.408669] In-situ OAM (IOAM) with IPv6 <6>[ 1.413260] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.420601] NET: Registered PF_PACKET protocol family <6>[ 1.426223] NET: Registered PF_KEY protocol family <5>[ 1.431597] Key type dns_resolver registered <6>[ 1.436533] ThumbEE CPU extension supported. <5>[ 1.441215] Registering SWP/SWPB emulation handler <3>[ 1.446911] omap_voltage_late_init: Voltage driver support not added <6>[ 1.454161] SmartReflex Class3 initialized <5>[ 1.623270] Loading compiled-in X.509 certificates <6>[ 1.664255] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 1.687942] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 1.802405] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 1.821186] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 1.842274] /ocp/interconnect@44c00000/segment@200000/target-module@10000/scm@0/pinmux@800: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@10000/scm@0/pinmux@800/clkout2-pins <6>[ 1.862943] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <3>[ 1.874158] ti-sysc 44e31000.target-module: probe with driver ti-sysc failed with error -16 <6>[ 2.058565] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <3>[ 2.084153] ti-sysc 48040000.target-module: probe with driver ti-sysc failed with error -16 <6>[ 2.224149] OMAP GPIO hardware version 0.1 <6>[ 2.265944] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <3>[ 2.318866] 48000000.interconnect:segment@200000:target-module@0:mpu@0:fck: device ID is greater than 24 <6>[ 2.330040] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <6>[ 2.350523] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <6>[ 2.369061] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 2.387015] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <4>[ 2.415369] sdhci-omap 481d8000.mmc: supply pbias not found, using dummy regulator <4>[ 2.433207] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 2.612991] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.181187] Freeing initrd memory: 15364K <6>[ 3.285052] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.295451] cpsw-switch 4a100000.switch: initialized cpsw ale version 1.4 <6>[ 3.302809] cpsw-switch 4a100000.switch: ALE Table size 1024, Policers 0 <6>[ 3.310313] cpsw-switch 4a100000.switch: cpts: overflow check period 500 (jiffies) <6>[ 3.318485] cpsw-switch 4a100000.switch: CPTS: ref_clk_freq:250000000 calc_mult:2147483648 calc_shift:29 error:0 nsec/sec <6>[ 3.330168] cpsw-switch 4a100000.switch: Detected MACID = 08:04:b4:96:48:24 <5>[ 3.339404] cpsw-switch 4a100000.switch: initialized (regs 0x4a100000, pool size 256) hw_ver:0019010C 1.12 (0) <3>[ 3.360631] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.369265] edma 49000000.dma: TI EDMA DMA engine driver <3>[ 3.394593] target-module@4b000000:target-module@140000:pmu@0:fck: device ID is greater than 24 <6>[ 3.406014] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 (8000000f) counters available <3>[ 3.423502] l3-aon-clkctrl:0000:0: failed to disable <6>[ 3.432292] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 34, base_baud = 3000000) is a 8250 <6>[ 3.441793] printk: legacy console [ttyS0] enabled <6>[ 3.441793] printk: legacy console [ttyS0] enabled <6>[ 3.452142] printk: legacy bootconsole [omap8250] disabled <6>[ 3.452142] printk: legacy bootconsole [omap8250] disabled <4>[ 3.483675] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 3.489993] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 3.501587] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 3.507978] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <6>[ 3.525613] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 3.543239] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 3.551940] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 3.561116] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 3.566424] sdhci-omap 48060000.mmc: supply pbias not found, using dummy regulator <4>[ 3.576640] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <4>[ 3.585428] sdhci-omap 481d8000.mmc: supply pbias not found, using dummy regulator <4>[ 3.594591] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.633224] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <6>[ 3.641828] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 3.650947] cpsw-switch 4a100000.switch: starting ndev. mode: dual_mac <6>[ 3.709912] mmc1: new high speed MMC card at address 0001 <6>[ 3.717005] mmcblk1: mmc1:0001 MK2704 3.53 GiB <6>[ 3.724911] mmcblk1: p1 <6>[ 3.728306] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 3.740028] mmcblk1boot0: mmc1:0001 MK2704 2.00 MiB <6>[ 3.747386] mmcblk1boot1: mmc1:0001 MK2704 2.00 MiB <6>[ 3.760679] mmcblk1rpmb: mmc1:0001 MK2704 512 KiB, chardev (250:0) <6>[ 5.883386] cpsw-switch 4a100000.switch eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 5.912634] Sending DHCP requests ., OK <6>[ 5.956866] IP-Config: Got DHCP answer from 192.168.175.254, my address is 192.168.175.42 <6>[ 5.965414] IP-Config: Complete: <6>[ 5.968922] device=eth0, hwaddr=08:04:b4:96:48:24, ipaddr=192.168.175.42, mask=255.255.255.0, gw=192.168.175.254 <6>[ 5.979877] host=beaglebone, domain=, nis-domain=(none) <6>[ 5.985849] bootserver=192.168.175.254, rootserver=192.168.175.254, rootpath= <6>[ 5.985860] nameserver0=192.168.175.254 <6>[ 5.998735] clk: Disabling unused clocks <6>[ 6.003236] PM: genpd: Disabling unused power domains <6>[ 6.010764] Freeing unused kernel image (initmem) memory: 1024K <6>[ 6.017737] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.278756] udevd[97]: starting version 3.2.9 <5>[ 8.672633] random: crng init done <27>[ 8.687934] udevd[97]: specified user 'tss' unknown <27>[ 8.693765] udevd[97]: specified group 'tss' unknown <30>[ 8.713907] udevd[98]: starting eudev-3.2.9 <4>[ 9.480031] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests (id=vbus) <6>[ 9.502354] remoteproc remoteproc0: wkup_m3 is available <6>[ 9.550104] usbcore: registered new interface driver usbfs <6>[ 9.556218] usbcore: registered new interface driver hub <6>[ 9.561927] usbcore: registered new device driver usb <4>[ 9.654541] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests (id=vbus) <4>[ 9.720392] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 9.842047] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 9.871333] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 9.908883] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.914790] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 9.973021] at24 2-0056: supply vcc not found, using dummy regulator <6>[ 10.033018] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 10.066375] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 10.075430] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 10.080853] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <4>[ 10.103578] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 10.134476] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12 <6>[ 10.143284] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 10.150814] usb usb1: Product: MUSB HDRC host driver <6>[ 10.156215] usb usb1: Manufacturer: Linux 6.12.0-rc7-next-20241111 musb-hcd <6>[ 10.163550] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 10.202082] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 10.247264] tda998x 0-0070: found TDA19988 <6>[ 10.453744] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 10.467945] hub 1-0:1.0: USB hub found <6>[ 10.532870] hub 1-0:1.0: 1 port detected <6>[ 10.676637] remoteproc remoteproc0: powering up wkup_m3 <4>[ 10.682343] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 10.692314] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 10.698595] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 10.811373] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_audio_codec_init [tda998x]) <6>[ 10.846306] omap_rng 48310000.rng: Random Number Generator ver. 20 <6>[ 10.871053] [drm] Initialized tilcdc 1.0.0 for 4830e000.lcdc on minor 0 <6>[ 10.916814] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 11.036243] PM: Cannot get wkup_m3_ipc handle <6>[ 11.092894] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 11.146690] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 11.199076] omap-sham 53100000.sham: will run requests pump with realtime priority <3>[ 11.208274] PM: Cannot get wkup_m3_ipc handle <6>[ 11.214906] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 11.253619] PM: Cannot get wkup_m3_ipc handle <6>[ 11.294776] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 12.127813] PM: Cannot get wkup_m3_ipc handle <3>[ 12.183971] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1221392/environment . /lava-1221392/environment / # /lava-1221392/bin/lava-test-runner /lava-1221392/0 /lava-1221392/bin/lava-test-runner /lava-1221392/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1221392/0/tests/0_dmesg + cat uuid + UUID=1221392_1.5.2.4.1 <8>[ 13.258815] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 13.334966] <8>[ 13.403566] <8>[ 13.471550] + set +x <8>[ 13.484146] / #