Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'.  U-Boot SPL 2018.01-dirty (Jul 31 2024 - 16:15:46) Trying to boot from MMC2 U-Boot 2018.01-dirty (Jul 31 2024 - 16:15:46 +0200) CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 4 seconds U-Boot> setenv autoload no setenv autoload no U-Boot> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff U-Boot> dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.175.42 (12 ms) U-Boot> setenv serverip 192.168.32.2 setenv serverip 192.168.32.2 U-Boot> tftp 0x82000000 1221792/tftp-deploy-zx6lutic/kernel/zImage tftp 0x82000000 1221792/tftp-deploy-zx6lutic/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1221792/tftp-deploy-zx6lutic/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################### 2.1 MiB/s done Bytes transferred = 11059712 (a8c200 hex) U-Boot> tftp 0x83000000 1221792/tftp-deploy-zx6lutic/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1221792/tftp-deploy-zx6lutic/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1221792/tftp-deploy-zx6lutic/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 2.1 MiB/s done Bytes transferred = 17873109 (110b8d5 hex) U-Boot> setenv initrd_size ${filesize} setenv initrd_size ${filesize} U-Boot> tftp 0x88000000 1221792/tftp-deploy-zx6lutic/dtb/am335x-boneblack.dtb tftp 0x88000000 1221792/tftp-deploy-zx6lutic/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.32.2; our IP address is 192.168.175.42; sending through gateway 192.168.175.254 Filename '1221792/tftp-deploy-zx6lutic/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 2.2 MiB/s done Bytes transferred = 70544 (11390 hex) U-Boot> setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-11-12 7:23:23 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17873045 Bytes = 17 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801438f Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc7-next-20241112 (KernelCI@build-j373699-arm-gcc-12-multi-v7-defconfig-config-smp-n-zrftd) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 Tue Nov 12 07:10:58 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: legacy bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] printk: log buffer data + meta data: 131072 + 409600 = 540672 bytes <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130560 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1. <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008333] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019100] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033809] Console: colour dummy device 80x30 <3>[ 0.038696] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045729] This ensures that you still see kernel messages. Please <3>[ 0.052444] update your kernel commandline. <6>[ 0.057046] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096077] CPU: Testing write buffer coherency: ok <6>[ 0.101447] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106908] pid_max: default: 32768 minimum: 301 <6>[ 0.112075] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.119885] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.149614] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.163208] EFI services will not be available. <6>[ 0.168245] Memory: 405416K/522240K available (15360K kernel code, 2540K rwdata, 6760K rodata, 2048K init, 411K bss, 49980K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.184430] devtmpfs: initialized <6>[ 0.199054] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.207522] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.217929] futex hash table entries: 256 (order: -1, 3072 bytes, linear) <6>[ 0.230203] pinctrl core: initialized pinctrl subsystem <6>[ 0.240570] DMI not present or invalid. <6>[ 0.245920] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.254654] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.265756] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.265805] cpuidle: using governor menu <6>[ 0.296709] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 0.315224] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <6>[ 0.335403] No ATAGs? <6>[ 0.338031] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.349271] Serial: AMBA PL011 UART driver <6>[ 0.374286] iommu: Default domain type: Translated <6>[ 0.379566] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.387652] SCSI subsystem initialized <6>[ 0.420385] usbcore: registered new interface driver usbfs <6>[ 0.426333] usbcore: registered new interface driver hub <6>[ 0.432138] usbcore: registered new device driver usb <6>[ 0.438539] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.443952] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.453638] PTP clock support registered <6>[ 0.458068] EDAC MC: Ver: 3.0.0 <6>[ 0.506379] scmi_core: SCMI protocol bus registered <6>[ 0.514163] vgaarb: loaded <6>[ 0.517735] clocksource: Switched to clocksource dmtimer <6>[ 0.551901] NET: Registered PF_INET protocol family <6>[ 0.557484] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.566229] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.575234] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.583483] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.591768] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.599428] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.606330] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) <6>[ 0.613338] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) <6>[ 0.620924] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.700404] RPC: Registered named UNIX socket transport module. <6>[ 0.706782] RPC: Registered udp transport module. <6>[ 0.711910] RPC: Registered tcp transport module. <6>[ 0.717009] RPC: Registered tcp-with-tls transport module. <6>[ 0.722924] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.729833] PCI: CLS 0 bytes, default 64 <5>[ 0.735328] Initialise system trusted keyrings <6>[ 0.753576] Trying to unpack rootfs image as initramfs... <6>[ 0.818122] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 0.825585] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.858137] NFS: Registering the id_resolver key type <5>[ 0.863717] Key type id_resolver registered <5>[ 0.868329] Key type id_legacy registered <6>[ 0.872751] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.879924] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.948415] Key type asymmetric registered <5>[ 0.952936] Asymmetric key parser 'x509' registered <6>[ 0.958410] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.966287] io scheduler mq-deadline registered <6>[ 0.971231] io scheduler kyber registered <6>[ 0.975678] io scheduler bfq registered <6>[ 0.988748] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.308003] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.342178] msm_serial: driver initialized <6>[ 1.346948] SuperH (H)SCI(F) driver initialized <6>[ 1.352147] STMicroelectronics ASC driver initialized <6>[ 1.357754] STM32 USART driver initialized <6>[ 1.461544] brd: module loaded <6>[ 1.494275] loop: module loaded <6>[ 1.524172] CAN device driver interface <6>[ 1.529268] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.536099] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.541526] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.547964] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.553784] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.562749] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.568866] usbcore: registered new interface driver pegasus <6>[ 1.574982] usbcore: registered new interface driver asix <6>[ 1.580843] usbcore: registered new interface driver ax88179_178a <6>[ 1.587410] usbcore: registered new interface driver cdc_ether <6>[ 1.593720] usbcore: registered new interface driver smsc75xx <6>[ 1.599934] usbcore: registered new interface driver smsc95xx <6>[ 1.606133] usbcore: registered new interface driver net1080 <6>[ 1.612255] usbcore: registered new interface driver cdc_subset <6>[ 1.618646] usbcore: registered new interface driver zaurus <6>[ 1.624677] usbcore: registered new interface driver cdc_ncm <6>[ 1.633843] usbcore: registered new interface driver usb-storage <6>[ 1.644518] i2c_dev: i2c /dev entries driver <5>[ 1.661554] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 1.670714] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.677364] sdhci: Copyright(c) Pierre Ossman <6>[ 1.683639] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.691424] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.700885] usbcore: registered new interface driver usbhid <6>[ 1.706904] usbhid: USB HID core driver <6>[ 1.717883] NET: Registered PF_INET6 protocol family <6>[ 2.149003] Segment Routing with IPv6 <6>[ 2.153148] In-situ OAM (IOAM) with IPv6 <6>[ 2.157527] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.164723] NET: Registered PF_PACKET protocol family <6>[ 2.170247] can: controller area network core <6>[ 2.175061] NET: Registered PF_CAN protocol family <6>[ 2.180279] can: raw protocol <6>[ 2.183603] can: broadcast manager protocol <6>[ 2.188190] can: netlink gateway - max_hops=1 <5>[ 2.193638] Key type dns_resolver registered <6>[ 2.198645] ThumbEE CPU extension supported. <5>[ 2.203326] Registering SWP/SWPB emulation handler <3>[ 2.209018] omap_voltage_late_init: Voltage driver support not added <5>[ 2.378676] Loading compiled-in X.509 certificates <6>[ 2.433880] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 2.461455] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 2.596031] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 2.615393] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 2.640709] /ocp/interconnect@44c00000/segment@200000/target-module@10000/scm@0/pinmux@800: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@10000/scm@0/pinmux@800/clkout2-pins <6>[ 2.662034] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <3>[ 2.684031] ti-sysc 44e31000.target-module: probe with driver ti-sysc failed with error -16 <6>[ 2.953213] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <3>[ 2.985840] ti-sysc 48040000.target-module: probe with driver ti-sysc failed with error -16 <6>[ 3.208970] OMAP GPIO hardware version 0.1 <6>[ 3.226182] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <4>[ 3.301774] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 3.349925] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 3.386578] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 3.422731] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 3.462671] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <3>[ 3.528851] 48000000.interconnect:segment@200000:target-module@0:mpu@0:fck: device ID is greater than 24 <6>[ 3.542691] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <6>[ 3.565136] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <6>[ 3.584136] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 3.602033] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <4>[ 3.631182] sdhci-omap 481d8000.mmc: supply pbias not found, using dummy regulator <4>[ 3.648756] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.878620] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 3.903053] random: crng init done <6>[ 3.948357] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.084203] Freeing initrd memory: 17456K <6>[ 4.180012] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.190185] cpsw-switch 4a100000.switch: initialized cpsw ale version 1.4 <6>[ 4.197453] cpsw-switch 4a100000.switch: ALE Table size 1024, Policers 0 <6>[ 4.204885] cpsw-switch 4a100000.switch: cpts: overflow check period 500 (jiffies) <6>[ 4.212976] cpsw-switch 4a100000.switch: CPTS: ref_clk_freq:250000000 calc_mult:2147483648 calc_shift:29 error:0 nsec/sec <6>[ 4.224568] cpsw-switch 4a100000.switch: Detected MACID = 08:04:b4:96:48:24 <5>[ 4.233165] cpsw-switch 4a100000.switch: initialized (regs 0x4a100000, pool size 256) hw_ver:0019010C 1.12 (0) <3>[ 4.260726] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.269240] edma 49000000.dma: TI EDMA DMA engine driver <3>[ 4.330608] target-module@4b000000:target-module@140000:pmu@0:fck: device ID is greater than 24 <6>[ 4.343966] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 (8000000f) counters available <3>[ 4.361349] l3-aon-clkctrl:0000:0: failed to disable <6>[ 4.428574] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 36, base_baud = 3000000) is a 8250 <6>[ 4.437943] printk: legacy console [ttyS0] enabled <6>[ 4.437943] printk: legacy console [ttyS0] enabled <6>[ 4.448237] printk: legacy bootconsole [omap8250] disabled <6>[ 4.448237] printk: legacy bootconsole [omap8250] disabled <4>[ 4.488286] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.495476] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.513240] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.520005] /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <6>[ 4.537576] /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0 <6>[ 4.555289] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.573796] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.582933] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.588050] sdhci-omap 48060000.mmc: supply pbias not found, using dummy regulator <4>[ 4.600926] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <4>[ 4.609348] sdhci-omap 481d8000.mmc: supply pbias not found, using dummy regulator <4>[ 4.617425] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.713969] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 4.740933] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.787899] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <6>[ 4.796648] cpsw-switch 4a100000.switch: starting ndev. mode: dual_mac <6>[ 4.855842] mmc1: new high speed MMC card at address 0001 <6>[ 4.862682] mmcblk1: mmc1:0001 MK2704 3.53 GiB <6>[ 4.870505] mmcblk1: p1 <6>[ 4.873953] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 4.885542] mmcblk1boot0: mmc1:0001 MK2704 2.00 MiB <6>[ 4.892802] mmcblk1boot1: mmc1:0001 MK2704 2.00 MiB <6>[ 4.905449] mmcblk1rpmb: mmc1:0001 MK2704 512 KiB, chardev (236:0) <6>[ 7.028774] cpsw-switch 4a100000.switch eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 7.057767] Sending DHCP requests ., OK <6>[ 7.101958] IP-Config: Got DHCP answer from 192.168.175.254, my address is 192.168.175.42 <6>[ 7.110533] IP-Config: Complete: <6>[ 7.114061] device=eth0, hwaddr=08:04:b4:96:48:24, ipaddr=192.168.175.42, mask=255.255.255.0, gw=192.168.175.254 <6>[ 7.125076] host=beaglebone, domain=, nis-domain=(none) <6>[ 7.131080] bootserver=192.168.175.254, rootserver=192.168.175.254, rootpath= <6>[ 7.131109] nameserver0=192.168.175.254 <6>[ 7.144378] clk: Disabling unused clocks <6>[ 7.148992] PM: genpd: Disabling unused power domains <6>[ 7.165428] Freeing unused kernel image (initmem) memory: 2048K <6>[ 7.174358] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.358669] udevd[96]: starting version 3.2.9 <27>[ 7.374237] udevd[96]: specified user 'tss' unknown <27>[ 7.380223] udevd[96]: specified group 'tss' unknown <30>[ 7.398875] udevd[97]: starting eudev-3.2.9 <4>[ 9.261840] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests (id=vbus) <6>[ 9.520811] tda998x 0-0070: found TDA19988 <4>[ 9.589992] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests (id=vbus) <6>[ 9.699663] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.705331] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.878297] hub 1-0:1.0: USB hub found <6>[ 9.961129] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1221792/environment . /lava-1221792/environment / # /lava-1221792/bin/lava-test-runner /lava-1221792/0 /lava-1221792/bin/lava-test-runner /lava-1221792/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1221792/0/tests/0_dmesg + cat uuid + UUID=1221792_1.5.2.4.1 + set +x <8>[ 12.886346] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.941979] <8>[ 12.990997] <8>[ 13.040345] + set +x <8>[ 13.050845] / #