Trying 192.168.56.21... Connected to conserv1. Escape character is '^]'. ser2net port telnet,3004 device serialdev, /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.2.2.2:1.0-port0, 115200n81, local=false [] (Debian GNU/Linux) U-Boot SPL 2015.10-00061-g68849f9 (Jan 08 2016 - 17:01:43) U-Boot 2015.10-00061-g68849f9 (Jan 08 2016 - 17:01:43 +0100) CPU: Freescale i.MX6DL rev1.1 at 792 MHz Reset cause: POR Board: UDOO DualLite DRAM: 1 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment No panel detected: default to HDMI Display: HDMI (1024x768) In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME] Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp FEC Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.6.14 (784 ms) => setenv serverip 192.168.6.2 setenv serverip 192.168.6.2 => tftp 0x12000000 978554/tftp-deploy-zyc1nfri/kernel/zImage tftp 0x12000000 978554/tftp-deploy-zyc1nfri/kernel/zImage Using FEC device TFTP from server 192.168.6.2; our IP address is 192.168.6.14 Filename '978554/tftp-deploy-zyc1nfri/kernel/zImage'. Load address: 0x12000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 7.3 MiB/s done Bytes transferred = 12132864 (b92200 hex) => tftp 0x13000000 978554/tftp-deploy-zyc1nfri/ramdisk/ramdisk.cpio.gz.uboot tftp 0x13000000 978554/tftp-deploy-zyc1nfri/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.6.2; our IP address is 192.168.6.14 Filename '978554/tftp-deploy-zyc1nfri/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x13000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################## 7.9 MiB/s done Bytes transferred = 18559417 (11b31b9 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x18000000 978554/tftp-deploy-zyc1nfri/dtb/imx6dl-udoo.dtb tftp 0x18000000 978554/tftp-deploy-zyc1nfri/dtb/imx6dl-udoo.dtb Using FEC device TFTP from server 192.168.6.2; our IP address is 192.168.6.14 Filename '978554/tftp-deploy-zyc1nfri/dtb/imx6dl-udoo.dtb'. Load address: 0x18000000 Loading: *### 5.6 MiB/s done Bytes transferred = 35141 (8945 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x12000000 0x13000000 0x18000000 bootz 0x12000000 0x13000000 0x18000000 Kernel image @ 0x12000000 [ 0x000000 - 0xb92200 ] ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 18559353 Bytes = 17.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800b944 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc7-next-20241112 (KernelCI@build-j373760-arm-clang-17-multi-v7-defconfig-964p7) (Debian clang version 17.0.6 (++20231208085813+6009708b4367-1~exp1~20231208085906.81), Debian LLD 17.0.6) #1 SMP Tue Nov 12 07:33:51 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Udoo i.MX6 Dual-lite Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x021e8000 (options '') [ 0.000000] printk: legacy bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT [ 0.000000] percpu: Embedded 17 pages/cpu s40140 r8192 d21300 u69632 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] printk: log buffer data + meta data: 131072 + 409600 = 540672 bytes <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 262144 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 512 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76450001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008439] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022243] Console: colour dummy device 80x30 <6>[ 0.024166] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034571] CPU: Testing write buffer coherency: ok <6>[ 0.039697] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044989] pid_max: default: 32768 minimum: 301 <6>[ 0.050032] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057454] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066413] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.125709] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.131314] rcu: Hierarchical SRCU implementation. <6>[ 0.134709] rcu: Max phase no-delay instances is 1000. <6>[ 0.140642] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.151758] EFI services will not be available. <6>[ 0.153977] smp: Bringing up secondary CPUs ... <6>[ 0.159608] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.159634] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.169912] smp: Brought up 1 node, 2 CPUs <6>[ 0.174063] SMP: Total of 2 processors activated (12.00 BogoMIPS). <6>[ 0.180529] CPU: All CPU(s) started in SVC mode. <6>[ 0.185954] Memory: 922100K/1048576K available (17408K kernel code, 2537K rwdata, 6740K rodata, 2048K init, 430K bss, 58044K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.201652] devtmpfs: initialized <6>[ 0.212255] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.217666] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.227488] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.237728] pinctrl core: initialized pinctrl subsystem <6>[ 0.243878] DMI not present or invalid. <6>[ 0.246172] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.253719] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.261740] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.261837] cpuidle: using governor menu <6>[ 0.269849] CPU identified as i.MX6DL, silicon rev 1.1 <6>[ 0.281337] /soc: Fixed dependency cycle(s) with /soc/bus@2000000/gpc@20dc000 <6>[ 0.285985] /soc/hdmi@120000: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.293371] /soc/interrupt-controller@a01000: Fixed dependency cycle(s) with /soc/interrupt-controller@a01000 <6>[ 0.303673] /soc/bus@2000000/clock-controller@20c4000: Fixed dependency cycle(s) with /soc/bus@2000000/gpc@20dc000 <6>[ 0.314203] /soc/bus@2000000/gpc@20dc000: Fixed dependency cycle(s) with /soc/bus@2000000/clock-controller@20c4000 <6>[ 0.324771] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.335044] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.345555] /soc/ipu@2400000: Fixed dependency cycle(s) with /soc/hdmi@120000 <6>[ 0.352645] /soc/ipu@2400000: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux <6>[ 0.362926] /soc/ipu@2400000: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux <6>[ 0.374017] /soc/hdmi@120000: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.382508] /soc/bus@2000000/clock-controller@20c4000: Fixed dependency cycle(s) with /soc/bus@2000000/gpc@20dc000 <6>[ 0.391299] /soc/bus@2000000/gpc@20dc000: Fixed dependency cycle(s) with /soc/bus@2000000/clock-controller@20c4000 <6>[ 0.401852] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.412108] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <4>[ 0.431072] mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator <4>[ 0.437005] mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator <6>[ 0.446140] /soc/bus@2000000/gpc@20dc000: Fixed dependency cycle(s) with /soc/bus@2000000/clock-controller@20c4000 <6>[ 0.455179] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.465019] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.475969] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.485847] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.502693] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.510284] /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.520525] /soc/hdmi@120000: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.527912] /soc/ipu@2400000: Fixed dependency cycle(s) with /soc/hdmi@120000 <6>[ 0.535285] /soc/ipu@2400000: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux <6>[ 0.545574] /soc/ipu@2400000: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux <6>[ 0.559275] No ATAGs? <6>[ 0.559440] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.567265] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.576324] imx6dl-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.588573] Serial: AMBA PL011 UART driver <4>[ 0.608836] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 0.617658] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 0.626400] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 0.635363] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 0.644666] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 0.653728] gpio gpiochip5: Static allocation of GPIO base is deprecated, use dynamic allocation. <4>[ 0.663014] gpio gpiochip6: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>[ 0.680641] iommu: Default domain type: Translated <6>[ 0.682851] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.699316] SCSI subsystem initialized <6>[ 0.701138] usbcore: registered new interface driver usbfs <6>[ 0.706319] usbcore: registered new interface driver hub <6>[ 0.711835] usbcore: registered new device driver usb <4>[ 0.717418] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests (id=vbus) <4>[ 0.726625] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests (id=vbus) <6>[ 0.737669] i2c i2c-1: IMX I2C adapter registered <6>[ 0.741377] i2c i2c-2: IMX I2C adapter registered <6>[ 0.747045] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.750853] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.760310] PTP clock support registered <6>[ 0.764664] EDAC MC: Ver: 3.0.0 <6>[ 0.775706] scmi_core: SCMI protocol bus registered <6>[ 0.781190] vgaarb: loaded <6>[ 0.790039] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.808178] NET: Registered PF_INET protocol family <6>[ 0.810750] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.820244] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.826762] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.834789] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.842849] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.850489] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.856955] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.863790] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.871263] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.877839] RPC: Registered named UNIX socket transport module. <6>[ 0.883167] RPC: Registered udp transport module. <6>[ 0.888099] RPC: Registered tcp transport module. <6>[ 0.893065] RPC: Registered tcp-with-tls transport module. <6>[ 0.898782] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.905527] PCI: CLS 0 bytes, default 64 <5>[ 0.911494] Initialise system trusted keyrings <6>[ 0.914990] Trying to unpack rootfs image as initramfs... <6>[ 0.940449] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.944751] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.960328] NFS: Registering the id_resolver key type <5>[ 0.962846] Key type id_resolver registered <5>[ 0.967245] Key type id_legacy registered <6>[ 0.971627] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.978469] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 0.986797] Key type asymmetric registered <5>[ 0.990518] Asymmetric key parser 'x509' registered <6>[ 0.995739] bounce: pool size: 64 pages <6>[ 0.999783] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.007414] io scheduler mq-deadline registered <6>[ 1.012186] io scheduler kyber registered <6>[ 1.016446] io scheduler bfq registered <6>[ 1.097429] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.147035] mxs-dma 110000.dma-controller: initialized <6>[ 1.309687] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.321462] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 267, base_baud = 5000000) is a IMX <6>[ 1.327650] printk: console [ttymxc1] enabled <6>[ 1.327650] printk: console [ttymxc1] enabled <6>[ 1.336915] printk: legacy bootconsole [ec_imx6q0] disabled <6>[ 1.336915] printk: legacy bootconsole [ec_imx6q0] disabled <6>[ 1.350461] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 268, base_baud = 5000000) is a IMX <6>[ 1.361764] msm_serial: driver initialized <6>[ 1.362493] SuperH (H)SCI(F) driver initialized <6>[ 1.363061] STMicroelectronics ASC driver initialized <6>[ 1.363274] STM32 USART driver initialized <6>[ 1.408182] brd: module loaded <6>[ 1.419454] loop: module loaded <6>[ 1.443431] CAN device driver interface <6>[ 1.445285] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.447420] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.447437] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.447490] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.447501] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.455329] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.455412] usbcore: registered new interface driver pegasus <6>[ 1.455461] usbcore: registered new interface driver asix <6>[ 1.455505] usbcore: registered new interface driver ax88179_178a <6>[ 1.455548] usbcore: registered new interface driver cdc_ether <6>[ 1.455591] usbcore: registered new interface driver smsc75xx <6>[ 1.455676] usbcore: registered new interface driver smsc95xx <6>[ 1.455723] usbcore: registered new interface driver net1080 <6>[ 1.455773] usbcore: registered new interface driver cdc_subset <6>[ 1.455817] usbcore: registered new interface driver zaurus <6>[ 1.455874] usbcore: registered new interface driver cdc_ncm <6>[ 1.463313] usbcore: registered new interface driver usb-storage <4>[ 1.465852] imx_usb 2184000.usb: No over current polarity defined <3>[ 2.476188] mxs_phy 20c9000.usbphy: Data pin can't make good contact. <4>[ 2.476986] imx_usb 2184200.usb: No over current polarity defined <6>[ 2.481471] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.481509] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.510306] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.516858] hub 1-0:1.0: USB hub found <6>[ 2.521120] hub 1-0:1.0: 1 port detected <6>[ 2.536420] i2c_dev: i2c /dev entries driver <6>[ 2.570301] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.570355] sdhci: Copyright(c) Pierre Ossman <6>[ 2.573910] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.576907] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.584772] usbcore: registered new interface driver usbhid <6>[ 2.584807] usbhid: USB HID core driver <4>[ 2.592452] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 2.617012] Freeing initrd memory: 18128K <6>[ 2.618199] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 2.620401] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 (8000003f) counters available <6>[ 2.622434] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 2.625115] NET: Registered PF_INET6 protocol family <6>[ 2.635381] Segment Routing with IPv6 <6>[ 2.635459] In-situ OAM (IOAM) with IPv6 <6>[ 2.635556] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.636301] NET: Registered PF_PACKET protocol family <6>[ 2.636315] can: controller area network core <6>[ 2.636368] NET: Registered PF_CAN protocol family <6>[ 2.636379] can: raw protocol <6>[ 2.636389] can: broadcast manager protocol <6>[ 2.636400] can: netlink gateway - max_hops=1 <5>[ 2.636928] Key type dns_resolver registered <6>[ 2.641540] ThumbEE CPU extension supported. <5>[ 2.641563] Registering SWP/SWPB emulation handler <5>[ 2.663785] Loading compiled-in X.509 certificates <6>[ 2.707369] pps pps0: new PPS source ptp0 <6>[ 2.763420] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 2.779178] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.782185] imx_thermal 20c8000.anatop:tempmon: Extended Commercial CPU temperature grade - max:105C critical:100C passive:95C <6>[ 2.810048] usb 1-1: new full-speed USB device number 2 using ci_hdrc <4>[ 2.828183] mmc2: host does not support reading read-only switch, assuming write-enable <6>[ 2.836814] mmc2: new high speed SDXC card at address 59b4 <6>[ 2.843203] mmcblk2: mmc2:59b4 SD128 119 GiB <6>[ 2.850605] mmcblk2: p1 p2 <6>[ 2.863404] Micrel KSZ9031 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <3>[ 3.070107] usb 1-1: device descriptor read/64, error -71 <3>[ 3.400156] usb 1-1: device descriptor read/64, error -71 <6>[ 3.640172] usb 1-1: new full-speed USB device number 3 using ci_hdrc <3>[ 3.870099] usb 1-1: device descriptor read/64, error -71 <3>[ 4.200145] usb 1-1: device descriptor read/64, error -71 <6>[ 4.310191] usb usb1-port1: attempt power cycle <6>[ 4.730099] usb 1-1: new full-speed USB device number 4 using ci_hdrc <3>[ 5.210129] usb 1-1: device not accepting address 4, error -71 <6>[ 5.340146] usb 1-1: new full-speed USB device number 5 using ci_hdrc <3>[ 5.820146] usb 1-1: device not accepting address 5, error -71 <3>[ 5.826441] usb usb1-port1: unable to enumerate USB device <6>[ 6.010816] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <5>[ 6.040054] Sending DHCP requests .., OK <6>[ 8.844489] IP-Config: Got DHCP answer from 192.168.6.1, my address is 192.168.6.14 <6>[ 8.844551] IP-Config: Complete: <6>[ 8.844567] device=eth0, hwaddr=00:c0:08:88:29:80, ipaddr=192.168.6.14, mask=255.255.255.0, gw=192.168.6.1 <6>[ 8.844604] host=192.168.6.14, domain=, nis-domain=(none) <6>[ 8.844624] bootserver=192.168.6.1, rootserver=192.168.6.1, rootpath= <6>[ 8.844646] nameserver0=10.255.253.1 <6>[ 8.845097] clk: Disabling unused clocks <6>[ 8.845570] PM: genpd: Disabling unused power domains <6>[ 8.869357] Freeing unused kernel image (initmem) memory: 2048K <6>[ 8.874715] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.030162] udevd[96]: starting version 3.2.9 <5>[ 14.570033] random: crng init done <27>[ 14.577865] udevd[96]: specified user 'tss' unknown <27>[ 14.578040] udevd[96]: specified group 'tss' unknown <30>[ 14.581355] udevd[97]: starting eudev-3.2.9 <6>[ 15.273946] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.278061] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 15.283383] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.286212] etnaviv-gpu 130000.gpu: model: GC880, revision: 5106 <6>[ 15.309526] caam 2100000.crypto: Entropy delay = 3200 <6>[ 15.310265] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 15.311559] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 <6>[ 15.316534] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.31a with HDCP (DWC HDMI 3D TX PHY) <6>[ 15.322084] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 15.334560] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.334589] caam 2100000.crypto: device ID = 0x0a16010000000100 (Era 4) <6>[ 15.334605] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 15.434067] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops cleanup_module [imxdrm]) <6>[ 15.434271] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops cleanup_module [imxdrm]) <6>[ 15.434342] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_ops [dw_hdmi_imx]) <6>[ 15.448175] [drm] Initialized imx-drm 1.0.0 for display-subsystem on minor 1 <6>[ 15.448266] imx-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 15.449312] imx-drm display-subsystem: [drm] Cannot find any crtc or sizes <4>[ 15.663032] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 15.678592] usbcore: registered new device driver onboard-usb-dev <4>[ 15.711326] onboard-usb-dev 2184200.usb:usb-port@1: supply vdd not found, using dummy regulator <6>[ 16.060211] usb 1-1: new high-speed USB device number 6 using ci_hdrc <6>[ 16.233800] hub 1-1:1.0: USB hub found <6>[ 16.240465] hub 1-1:1.0: 4 ports detected <6>[ 16.361137] caam algorithms registered in /proc/crypto <6>[ 16.361390] caam 2100000.crypto: registering rng-caam <6>[ 16.362395] caam 2100000.crypto: rng crypto API alg registered prng-caam done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK <6>[ 16.540322] usb 1-1.3: new high-speed USB device number 7 using ci_hdrc /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-978554/environment . /lava-978554/environment / # /lava-978554/bin/lava-test-runner /lava-978554/0 /lava-978554/bin/lava-test-runner /lava-978554/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-978554/0/tests/0_dmesg + cat uuid + UUID=978554_1.5.2.4.1<8>[ 17.130953] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.184022] <8>[ 17.217423] <8>[ 17.262649] + set +x <8>[ 17.273379] / #