Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. Xilinx Zynq MP First Stage Boot Loader Release 2019.1 May 25 2019 - 06:59:26 NOTICE: ATF running on XCZU9EG/silicon v4/RTL5.1 at 0xfffea000 NOTICE: BL31: Secure code at 0x0 NOTICE: BL31: Non secure code at 0x10080000 NOTICE: BL31: v2.0(release):xilinx-v2018.3-720-g80d1c790 NOTICE: BL31: Built : 07:08:32, May 25 2019 PMUFW: v1.1 U-Boot 2019.01 (May 25 2019 - 06:55:09 +0000) Model: ZynqMP ZCU102 Rev1.0 Board: Xilinx ZynqMP DRAM: 4 GiB EL Level: EL2 Chip ID: zu9eg MMC: mmc@ff170000: 0 Loading Environment from SPI Flash... SF: Detected n25q512a with page size 512 Bytes, erase size 128 KiB, total 128 MiB OK In: serial@ff000000 Out: serial@ff000000 Err: serial@ff000000 Model: ZynqMP ZCU102 Rev1.0 Board: Xilinx ZynqMP Net: ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id Warning: ethernet@ff0e0000 MAC addresses don't match: Address in ROM is 01:02:03:04:05:06 Address in environment is 12:6c:0e:30:34:fe eth0: ethernet@ff0e0000 Hit any key to stop autoboot: 4  0 ZynqMP> setenv autoload no setenv autoload no ZynqMP> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff ZynqMP> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff ZynqMP> dhcp dhcp ethernet@ff0e0000 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.11.7 (252 ms) ZynqMP> setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 ZynqMP> tftpboot 0x80000 1221789/tftp-deploy-vpsirgsl/kernel/Image tftpboot 0x80000 1221789/tftp-deploy-vpsirgsl/kernel/Image Using ethernet@ff0e0000 device TFTP from server 192.168.11.5; our IP address is 192.168.11.7 Filename '1221789/tftp-deploy-vpsirgsl/kernel/Image'. Load address: 0x80000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###############T ################################################## ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 5.6 MiB/s done Bytes transferred = 66982400 (3fe1200 hex) ZynqMP> tftpboot 0x10000000 1221789/tftp-deploy-vpsirgsl/ramdisk/ramdisk.cpio.gz.uboot tftpboot 0x10000000 1221789/tftp-deploy-vpsirgsl/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@ff0e0000 device TFTP from server 192.168.11.5; our IP address is 192.168.11.7 Filename '1221789/tftp-deploy-vpsirgsl/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################## 9.8 MiB/s done Bytes transferred = 33974102 (2066756 hex) ZynqMP> tftpboot 0x14000000 1221789/tftp-deploy-vpsirgsl/dtb/zynqmp-zcu102-rev1.0.dtb tftpboot 0x14000000 1221789/tftp-deploy-vpsirgsl/dtb/zynqmp-zcu102-rev1.0.dtb Using ethernet@ff0e0000 device TFTP from server 192.168.11.5; our IP address is 192.168.11.7 Filename '1221789/tftp-deploy-vpsirgsl/dtb/zynqmp-zcu102-rev1.0.dtb'. Load address: 0x14000000 Loading: *### 6.5 MiB/s done Bytes transferred = 40941 (9fed hex) ZynqMP> setenv bootargs 'console=ttyPS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyPS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' ZynqMP> booti 0x80000 0x10000000 0x14000000 booti 0x80000 0x10000000 0x14000000 ## Loading init Ramdisk from Legacy Image at 10000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 33974038 Bytes = 32.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 14000000 Booting using the fdt blob at 0x14000000 Loading Ramdisk to 7bd37000, end 7dd9d716 ... OK Loading Device Tree to 000000007bd2a000, end 000000007bd36fec ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.12.0-rc7-next-20241112 (KernelCI@build-j373651-arm64-gcc-12-defconfig-kselftest-24sqh) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Tue Nov 12 07:02:12 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: ZynqMP ZCU102 Rev1.0 [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [cdns0] enabled [ 0.000000] OF: reserved mem: 0x000000003ed00000..0x000000003ed3ffff (256 KiB) nomap non-reusable memory@3ed00000 [ 0.000000] OF: reserved mem: 0x000000003ef00000..0x000000003ef3ffff (256 KiB) nomap non-reusable memory@3ef00000 [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000087fffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x87f7c30c0-0x87f7c57ff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000087fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000003ecfffff] [ 0.000000] node 0: [mem 0x000000003ed00000-0x000000003ed3ffff] [ 0.000000] node 0: [mem 0x000000003ed40000-0x000000003eefffff] [ 0.000000] node 0: [mem 0x000000003ef00000-0x000000003ef3ffff] [ 0.000000] node 0: [mem 0x000000003ef40000-0x000000007fefffff] [ 0.000000] node 0: [mem 0x0000000800000000-0x000000087fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000087fffffff] [ 0.000000] On node 0, zone Normal: 256 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x000000007de00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 34 pages/cpu s100056 r8192 d31016 u139264 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyPS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1048320 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:on <6>[ 0.000000] mem auto-init: clearing system memory may take some time... <6>[ 0.000000] stackdepot: allocating hash table via alloc_large_system_hash <6>[ 0.000000] stackdepot hash table entries: 262144 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] software IO TLB: area num 4. <6>[ 0.000000] software IO TLB: mapped [mem 0x0000000077d2a000-0x000000007bd2a000] (64MB) <4>[ 0.000000] ********************************************************** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** This system shows unhashed kernel memory addresses ** <4>[ 0.000000] ** via the console, logs, and other interfaces. This ** <4>[ 0.000000] ** might reduce the security of your system. ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** If you see this message and you are not debugging ** <4>[ 0.000000] ** the kernel, report this immediately to your system ** <4>[ 0.000000] ** administrator! ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ********************************************************** <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 76788 entries in 300 pages <6>[ 0.000000] ftrace: allocated 300 pages with 4 groups <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <4>[ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0x1ffffffffffffff max_cycles: 0x170f8de2d3, max_idle_ns: 440795206112 ns <6>[ 0.000001] sched_clock: 57 bits at 100MHz, resolution 10ns, wraps every 4398046511101ns <6>[ 0.009626] Console: colour dummy device 80x25 <6>[ 0.013187] Calibrating delay loop (skipped), value calculated using timer frequency.. 199.98 BogoMIPS (lpj=99990) <6>[ 0.023547] pid_max: default: 32768 minimum: 301 <6>[ 0.028815] LSM: initializing lsm=capability,landlock,bpf,ima <6>[ 0.034623] landlock: Up and running. <6>[ 0.039129] LSM support for eBPF active <6>[ 0.042845] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.049940] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.067197] rcu: Hierarchical SRCU implementation. <6>[ 0.067263] rcu: Max phase no-delay instances is 400. <6>[ 0.072712] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.089835] EFI services will not be available. <6>[ 0.090715] smp: Bringing up secondary CPUs ... <6>[ 0.095519] Detected VIPT I-cache on CPU1 <6>[ 0.095613] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.098804] Detected VIPT I-cache on CPU2 <6>[ 0.098862] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] <6>[ 0.100486] Detected VIPT I-cache on CPU3 <6>[ 0.100542] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] <6>[ 0.100755] smp: Brought up 1 node, 4 CPUs <6>[ 0.132500] SMP: Total of 4 processors activated. <6>[ 0.137398] CPU: All CPU(s) started at EL2 <6>[ 0.141732] CPU features: detected: 32-bit EL0 Support <6>[ 0.147075] CPU features: detected: 32-bit EL1 Support <6>[ 0.152495] CPU features: detected: CRC32 instructions <6>[ 0.157879] alternatives: applying system-wide alternatives <6>[ 0.166428] Memory: 3900844K/4193280K available (24704K kernel code, 7876K rwdata, 14884K rodata, 17792K init, 868K bss, 252152K reserved, 32768K cma-reserved) <6>[ 0.179790] devtmpfs: initialized <6>[ 0.237465] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.241858] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.255002] 16176 pages in range for non-PLT usage <6>[ 0.255017] 507696 pages in range for PLT usage <6>[ 0.255784] pinctrl core: initialized pinctrl subsystem <6>[ 0.273343] DMI not present or invalid. <6>[ 0.278556] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.282361] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.286647] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.295021] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.302669] audit: initializing netlink subsys (disabled) <5>[ 0.308579] audit: type=2000 audit(0.139:1): state=initialized audit_enabled=0 res=1 <6>[ 0.314305] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.316055] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.322557] cpuidle: using governor menu <6>[ 0.334361] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.340348] ASID allocator initialised with 65536 entries <6>[ 0.358270] Serial: AMBA PL011 UART driver <6>[ 0.394276] /axi/interrupt-controller@f9010000: Fixed dependency cycle(s) with /axi/interrupt-controller@f9010000 <6>[ 0.400313] /axi/pcie@fd0e0000: Fixed dependency cycle(s) with /axi/pcie@fd0e0000 <6>[ 0.441360] /axi/pcie@fd0e0000: Fixed dependency cycle(s) with /axi/pcie@fd0e0000 <6>[ 0.443917] /axi/pcie@fd0e0000: Fixed dependency cycle(s) with /axi/pcie@fd0e0000/legacy-interrupt-controller <6>[ 0.511111] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.512549] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.519029] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.526034] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.532524] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.539530] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.546019] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.553024] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.568227] ACPI: Interpreter disabled. <6>[ 0.583328] iommu: Default domain type: Translated <6>[ 0.583387] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.594843] SCSI subsystem initialized <6>[ 0.596872] usbcore: registered new interface driver usbfs <6>[ 0.599100] usbcore: registered new interface driver hub <6>[ 0.604644] usbcore: registered new device driver usb <6>[ 0.614250] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.614950] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.624378] PTP clock support registered <6>[ 0.629088] EDAC MC: Ver: 3.0.0 <6>[ 0.633435] scmi_core: SCMI protocol bus registered <6>[ 0.639595] zynqmp-ipi-mbox mailbox@ff9905c0: Registered ZynqMP IPI mbox with TX/RX channels. <6>[ 0.649921] FPGA manager framework <6>[ 0.650627] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.658588] NET: Registered PF_ATMPVC protocol family <6>[ 0.660888] NET: Registered PF_ATMSVC protocol family <6>[ 0.667314] vgaarb: loaded <6>[ 0.670563] clocksource: Switched to clocksource arch_sys_counter <5>[ 1.474605] VFS: Disk quotas dquot_6.6.0 <6>[ 1.474738] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 1.482518] pnp: PnP ACPI: disabled <6>[ 1.512400] NET: Registered PF_INET protocol family <6>[ 1.512767] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.523645] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 1.528392] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.536313] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.544598] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 1.552759] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.559420] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear) <6>[ 1.566508] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 1.573352] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 1.581305] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.588205] RPC: Registered named UNIX socket transport module. <6>[ 1.592640] RPC: Registered udp transport module. <6>[ 1.597568] RPC: Registered tcp transport module. <6>[ 1.602497] RPC: Registered tcp-with-tls transport module. <6>[ 1.608207] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.614904] NET: Registered PF_XDP protocol family <6>[ 1.619903] PCI: CLS 0 bytes, default 64 <6>[ 1.624828] Unpacking initramfs... <6>[ 1.648767] kvm [1]: nv: 557 coarse grained trap handlers <6>[ 1.649975] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.656436] kvm [1]: vgic interrupt IRQ9 <6>[ 1.657569] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 1.669992] Initialise system trusted keyrings <6>[ 1.670660] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.691876] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.693703] NFS: Registering the id_resolver key type <5>[ 1.697705] Key type id_resolver registered <5>[ 1.702043] Key type id_legacy registered <6>[ 1.706414] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.713212] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.721450] 9p: Installing v9fs 9p2000 file system support <6>[ 1.781743] NET: Registered PF_ALG protocol family <5>[ 1.781857] Key type asymmetric registered <5>[ 1.785534] Asymmetric key parser 'x509' registered <6>[ 1.790983] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) <6>[ 1.798245] io scheduler mq-deadline registered <6>[ 1.802994] io scheduler kyber registered <6>[ 1.807366] io scheduler bfq registered <4>[ 1.812226] test_firmware: interface ready <6>[ 1.884669] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.058966] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.077901] msm_serial: driver initialized <6>[ 2.079792] SuperH (H)SCI(F) driver initialized <6>[ 2.082019] STM32 USART driver initialized <6>[ 2.129363] loop: module loaded <6>[ 2.130014] lkdtm: No crash points registered, enable through debugfs <6>[ 2.140784] megasas: 07.727.03.00-rc1 <6>[ 2.187005] thunder_xcv, ver 1.0 <6>[ 2.187216] thunder_bgx, ver 1.0 <6>[ 2.188497] nicpf, ver 1.0 <6>[ 2.198098] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 2.199965] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 2.205730] hclge is initializing <6>[ 2.209239] e1000: Intel(R) PRO/1000 Network Driver <6>[ 2.214150] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 2.220328] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.225309] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.231692] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.237079] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.243082] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.249360] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.257674] sky2: driver version 1.30 <6>[ 2.266532] VFIO - User Level meta-driver version: 0.3 <6>[ 2.281859] usbcore: registered new interface driver usb-storage <6>[ 2.298730] i2c_dev: i2c /dev entries driver <6>[ 2.339295] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.340126] sdhci: Copyright(c) Pierre Ossman <6>[ 2.348393] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.355943] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.369738] zynqmp_firmware_probe Platform Management API v1.1 <6>[ 2.370226] zynqmp_firmware_probe Trustzone version v1.0 <6>[ 2.485139] hid: raw HID events driver (C) Jiri Kosina <6>[ 2.489048] usbcore: registered new interface driver usbhid <6>[ 2.490744] usbhid: USB HID core driver <6>[ 2.514355] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 (0,8000003f) counters available <6>[ 2.529468] optee: probing for conduit method. <4>[ 2.529579] optee: api uid mismatch <3>[ 2.532297] optee firmware:optee: probe with driver optee failed with error -22 <6>[ 2.557319] GACT probability on <6>[ 2.560111] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.562711] IPv4 over IPsec tunneling driver <6>[ 2.567010] IPsec XFRM device driver <6>[ 2.569501] NET: Registered PF_INET6 protocol family <6>[ 2.578744] Segment Routing with IPv6 <6>[ 2.579032] In-situ OAM (IOAM) with IPv6 <6>[ 2.584808] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.592369] NET: Registered PF_PACKET protocol family <6>[ 2.593915] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <6>[ 2.607969] 9pnet: Installing 9P2000 support <5>[ 2.611695] Key type dns_resolver registered <6>[ 2.616791] NET: Registered PF_VSOCK protocol family <6>[ 2.621213] mpls_gso: MPLS GSO support <6>[ 2.715988] registered taskstats version 1 <5>[ 2.728663] Loading compiled-in X.509 certificates <6>[ 3.649570] Freeing initrd memory: 33176K <5>[ 3.716578] Loaded X.509 cert 'Build time autogenerated kernel key: 2881f7bbbba7205897bdf74b87ee886de6e82b3c' <6>[ 3.782681] Demotion targets for Node 0: null <6>[ 3.783690] ima: No TPM chip found, activating TPM-bypass! <6>[ 3.787440] ima: Allocated hash algorithm: sha1 <6>[ 3.792270] ima: No architecture policies found <4>[ 3.884071] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 18 <4>[ 3.887961] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 19 <4>[ 3.897382] The requested pinctrl feature is not supported in the current firmware. <4>[ 3.897382] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 3.913189] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: ailed to set: pin 18 param 2 value 0 <6>[ 3.925412] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 19, base_baud = 6249999) is a xuartps <6>[ 3.937699] printk: legacy console [ttyPS0] enabled <6>[ 3.937699] printk: legacy console [ttyPS0] enabled <6>[ 3.942895] printk: legacy bootconsole [cdns0] disabled <6>[ 3.942895] printk: legacy bootconsole [cdns0] disabled <4>[ 3.960033] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 20 <4>[ 3.969603] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 21 <4>[ 3.979128] The requested pinctrl feature is not supported in the current firmware. <4>[ 3.979128] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 3.995060] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 21 param 2 value 0 <6>[ 4.006647] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 20, base_baud = 6249999) is a xuartps <4>[ 4.034377] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 64 <4>[ 4.043937] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 65 <4>[ 4.053482] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 66 <4>[ 4.063029] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 67 <4>[ 4.072591] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 68 <4>[ 4.082164] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 69 <4>[ 4.091702] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 70 <4>[ 4.101223] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 71 <4>[ 4.110762] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 72 <4>[ 4.120285] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 73 <4>[ 4.129808] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 74 <4>[ 4.139358] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 75 <4>[ 4.148879] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.148879] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.164796] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 70 param 2 value 0 <4>[ 4.174020] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.174020] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.189934] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 71 param 2 value 0 <4>[ 4.199160] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.199160] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.215075] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 72 param 2 value 0 <4>[ 4.224310] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.224310] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.240222] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 73 param 2 value 0 <4>[ 4.249448] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.249448] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.265363] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 74 param 2 value 0 <4>[ 4.274588] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.274588] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.290501] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 75 param 2 value 0 <4>[ 4.299862] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 76 <4>[ 4.309397] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 77 <4>[ 4.384193] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 39 <4>[ 4.393590] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 64 <4>[ 4.393758] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 40 <4>[ 4.403225] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 65 <4>[ 4.412715] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 41 <4>[ 4.422200] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 66 <4>[ 4.431691] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 42 <4>[ 4.441174] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 67 <4>[ 4.450667] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 46 <4>[ 4.460149] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 68 <4>[ 4.469644] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 47 <4>[ 4.479128] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 69 <4>[ 4.488620] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 48 <4>[ 4.498111] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 70 <4>[ 4.507614] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 49 <4>[ 4.517097] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 71 <4>[ 4.526616] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 50 <4>[ 4.536108] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 72 <4>[ 4.545613] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 51 <4>[ 4.555064] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 73 <4>[ 4.564527] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.564527] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.574023] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 74 <4>[ 4.589878] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 45 param 2 value 0 <4>[ 4.589928] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 45 <4>[ 4.608653] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 75 <4>[ 4.618097] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.618097] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.627585] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.627585] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.643474] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 44 param 2 value 0 <4>[ 4.659427] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 70 param 2 value 0 <4>[ 4.668672] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 44 <4>[ 4.677838] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.677838] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.703262] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 71 param 2 value 0 <4>[ 4.712517] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.712517] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.728452] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 72 param 2 value 0 <6>[ 4.734312] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit <4>[ 4.737705] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.737705] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.761573] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 73 param 2 value 0 <4>[ 4.770824] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.770824] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 4.786754] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 74 param 2 value 0 <6>[ 4.788448] mmc0: new high speed SDHC card at address aaaa <4>[ 4.795996] The requested pinctrl feature is not supported in the current firmware. <4>[ 4.795996] Expected firmware version is 2023.1 and above for this feature to work. <6>[ 4.804867] mmcblk0: mmc0:aaaa SE16G 14.8 GiB <4>[ 4.817684] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 75 param 2 value 0 <6>[ 4.829750] mmcblk0: p1 p2 <4>[ 4.831701] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 76 <4>[ 4.844148] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 77 <4>[ 4.913666] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 64 <4>[ 4.923215] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 65 <4>[ 4.932739] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 66 <4>[ 4.942263] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 67 <4>[ 4.951785] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 68 <4>[ 4.961307] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 69 <4>[ 4.970829] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 70 <4>[ 4.980352] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 71 <4>[ 4.989876] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 72 <4>[ 4.999400] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 73 <4>[ 5.008932] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 74 <4>[ 5.018507] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 75 <4>[ 5.028013] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.028013] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.043924] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 70 param 2 value 0 <4>[ 5.053152] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.053152] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.069064] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 71 param 2 value 0 <4>[ 5.078290] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.078290] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.094203] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 72 param 2 value 0 <4>[ 5.103433] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.103433] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.119343] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 73 param 2 value 0 <4>[ 5.128570] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.128570] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.144494] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 74 param 2 value 0 <4>[ 5.153729] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.153729] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.169661] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 75 param 2 value 0 <4>[ 5.179068] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 76 <4>[ 5.188611] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 77 <4>[ 5.258459] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 64 <4>[ 5.268005] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 65 <4>[ 5.277566] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 66 <4>[ 5.287109] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 67 <4>[ 5.296632] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 68 <4>[ 5.306154] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 69 <4>[ 5.315678] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 70 <4>[ 5.325215] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 71 <4>[ 5.334740] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 72 <4>[ 5.344264] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 73 <4>[ 5.353786] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 74 <4>[ 5.363323] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 75 <4>[ 5.372833] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.372833] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.388745] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 70 param 2 value 0 <4>[ 5.397975] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.397975] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.413896] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 71 param 2 value 0 <4>[ 5.423130] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.423130] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.439043] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 72 param 2 value 0 <4>[ 5.448271] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.448271] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.464182] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 73 param 2 value 0 <4>[ 5.473409] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.473409] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.489322] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 74 param 2 value 0 <4>[ 5.498555] The requested pinctrl feature is not supported in the current firmware. <4>[ 5.498555] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 5.514470] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 75 param 2 value 0 <4>[ 5.523831] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 76 <4>[ 5.533375] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 77 <6>[ 25.583772] Waiting up to 100 more seconds for network. <6>[ 45.588767] Waiting up to 80 more seconds for network. <6>[ 65.593766] Waiting up to 60 more seconds for network. <4>[ 66.851010] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 53 <4>[ 66.860628] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 54 <4>[ 66.870208] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 55 <4>[ 66.879792] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 56 <4>[ 66.889373] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 57 <4>[ 66.898951] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 58 <4>[ 66.908571] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 59 <4>[ 66.918152] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 60 <4>[ 66.927734] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 61 <4>[ 66.937308] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 62 <4>[ 66.946883] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 63 <4>[ 66.956443] The requested pinctrl feature is not supported in the current firmware. <4>[ 66.956443] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 66.972423] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 52 param 2 value 0 <4>[ 66.981762] The requested pinctrl feature is not supported in the current firmware. <4>[ 66.981762] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 66.997745] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 53 param 2 value 0 <4>[ 67.007086] The requested pinctrl feature is not supported in the current firmware. <4>[ 67.007086] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 67.023066] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 55 param 2 value 0 <4>[ 67.059046] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regulator <4>[ 67.068018] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regulator <4>[ 67.093409] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 64 <4>[ 67.103404] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 65 <4>[ 67.113009] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 66 <4>[ 67.122622] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 67 <4>[ 67.132222] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 68 <4>[ 67.141821] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 69 <4>[ 67.151414] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 70 <4>[ 67.161007] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 71 <4>[ 67.170679] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 72 <4>[ 67.180280] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 73 <4>[ 67.189879] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 74 <4>[ 67.199471] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 75 <4>[ 67.209046] The requested pinctrl feature is not supported in the current firmware. <4>[ 67.209046] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 67.225029] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 70 param 2 value 0 <4>[ 67.234332] The requested pinctrl feature is not supported in the current firmware. <4>[ 67.234332] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 67.250314] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 71 param 2 value 0 <4>[ 67.259617] The requested pinctrl feature is not supported in the current firmware. <4>[ 67.259617] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 67.275616] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 72 param 2 value 0 <4>[ 67.284913] The requested pinctrl feature is not supported in the current firmware. <4>[ 67.284913] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 67.300904] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 73 param 2 value 0 <4>[ 67.310203] The requested pinctrl feature is not supported in the current firmware. <4>[ 67.310203] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 67.326187] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 74 param 2 value 0 <4>[ 67.335487] The requested pinctrl feature is not supported in the current firmware. <4>[ 67.335487] Expected firmware version is 2023.1 and above for this feature to work. <4>[ 67.351464] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin 75 param 2 value 0 <4>[ 67.360904] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 76 <4>[ 67.370520] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: Invalid IO Standard requested for pin 77 <4>[ 67.467365] platform ff9d0000.usb: deferred probe pending: dwc3-xilinx: failed to get USB3 PHY <4>[ 67.476391] platform leds: deferred probe pending: leds-gpio: Failed to get GPIO '/leds/heartbeat-led' <4>[ 67.486041] platform fd0c0000.ahci: deferred probe pending: (reason unknown) <4>[ 67.493413] platform ff0e0000.ethernet: deferred probe pending: (reason unknown) <4>[ 67.501221] platform gpio-keys: deferred probe pending: gpio-keys: failed to get gpio <6>[ 85.598770] Waiting up to 40 more seconds for network. <6>[ 105.603768] Waiting up to 20 more seconds for network. <5>[ 125.595814] Sending DHCP requests ...... timed out! <3>[ 212.875771] IP-Config: Reopening network devices... <6>[ 232.882770] Waiting up to 100 more seconds for network. <6>[ 252.887771] Waiting up to 80 more seconds for network.